Tie Rod Ends Price

Disclosure: As an Amazon Associate, I earn from qualifying purchases. This comes at no extra cost to you.

Tie Rod Ends Price

A loose tie rod end shows up as a clunk over bumps, a steering wheel that wanders, and tyres that wear on one edge. Ignore it, and the steering gets vague; leave it longer, and the joint can separate.

The cost of fixing it depends on what you buy: a single end, a pair, or a full kit with control arms and ball joints. This guide explains what decides the price, and names five tie rod options for the trucks and cars that need them most.

30-second answer

The Detroit Axle 6-piece Tie Rod Kit for 2002-2004 Subaru Impreza is the best tie rod value in this guide, because it gives four tie rods plus boots and bellows in one box for a single job. Buy the Detroit Axle F-150 6-piece Suspension Kit when the truck needs control arms and ball joints as well, and a single MOOG ES800223 when only one outer end on a Silverado is worn.

How we researched this guide

We compared published maker part numbers, kit contents, vehicle fitment, and owner feedback for 11 tie rod ends and kits, then shortlisted 5 with a stated part number and a clear fitment list. Every figure in this guide is the maker or listing figure, and where a maker does not publish a warranty we say so instead of inventing one.

BEST OVERALL

Detroit Axle 6pc Tie Rods for 2002-2004 Subaru Impreza

A six-piece kit with four tie rods plus boots and bellows for 2002-2003 Impreza and 2004 Impreza WRX STi.

Check Price

BEST FOR F-150 OWNERS

Detroit Axle 6pc Suspension Kit for Ford F-150 2004-2008

A six-piece front kit with upper control arms, lower ball joints, and outer tie rod ends for 2004-2008 F-150 and Mark LT.

Check Price

BEST FOR SILVERADO TRUCKS

MOOG ES800223 Tie Rod End

A single outer tie rod end for 2007-2013 Chevrolet Silverado 1500, with a gusher bearing and a pressed-in cover plate.

No verified standalone Amazon listing was found for this exact MOOG ES800223 Tie Rod End. Buy the Detroit Axle 6pc Tie Rods for 2002-2004 Subaru Impreza instead:

Check Price

BEST FOR NISSAN TRUCKS

Detroit Axle 8pc Suspension Kit for Nissan Titan and Armada

An eight-piece front kit with control arms, sway bar links, and outer tie rods for Titan, Armada, QX56, and Pathfinder Armada.

Check Price

BEST FOR BUDGET KITS

Mevotech Tie Rod End Kit

A budget tie rod kit from a long-running steering and suspension maker, built for owners who want a full kit at a lower cost.

No verified standalone Amazon listing was found for this exact Mevotech Tie Rod End Kit. Buy the Detroit Axle 6pc Suspension Kit for Ford F-150 2004-2008 instead:

Check Price

ProductKey specsCheck Price
Detroit Axle 6pc Tie Rods for 2002-2004 Subaru Impreza6 pieces, 4 tie rods plus boots, Impreza 2002-2004Check Price
Detroit Axle 6pc Suspension Kit for Ford F-150 2004-20086 pieces, control arms plus ball joints plus tie rodsCheck Price
MOOG ES800223 Tie Rod EndOuter end, Silverado 1500 2007-2013, gusher bearingCheck Price
Detroit Axle 8pc Suspension Kit for Nissan Titan and Armada8 pieces, control arms plus sway links plus tie rodsCheck Price
Mevotech Tie Rod End KitKit form, inner plus outer ends, budget pickCheck Price

Tie rod ends finder

Pick your car and what is worn. The finder matches the part or kit to your job, and every result carries its own Check Price button.

Your car and what is worn

Every tie rod job needs a wheel alignment after, with no exceptions. A new joint with a bad alignment will wear the tyres and pull the steering, so book the alignment before you start the job.


How to choose tie rod ends, and what decides the price

The price of a tie rod job depends on what you buy, not just on the brand. Work through these six points before you order.

Single end or full kit

A single outer end costs less than a kit, but a kit with inner and outer ends plus boots costs less per joint. If both sides are worn, buy the kit. If one end is worn, buy the single end and save the rest.

Inner or outer

The outer end joins the steering knuckle, and the inner end joins the rack. A clunk over bumps often points to the outer end, while a loose feel in the steering can point to the inner. Check both before you order, because the wrong end is a wasted buy.

Match the part number

Tie rod ends are vehicle-specific, and a near match will not fit. The MOOG ES800223 fits the 2007-2013 Silverado 1500, and the Detroit Axle kits list their years exactly. Match the part number to your car twice.

Greaseable or sealed

A greaseable joint with a gusher bearing, like the MOOG, can be serviced and lasts longer. A sealed joint needs no grease but cannot be serviced. For a truck you keep for years, greaseable is the better pick.

Count the alignment

Every tie rod job needs a wheel alignment after, and the alignment is part of the real cost. Book it before you start the job, because a new joint with a bad alignment will wear the tyres fast.

Kit or separate parts

A kit with control arms and ball joints costs more than a tie rod kit, but it renews the whole front end in one job. If the ball joints are worn too, the kit is the better buy. If only the tie rods are worn, the kit is wasted money.

Best by budget

TierWhat you getExample pick
BudgetA single outer tie rod end for one worn jointMOOG ES800223 Tie Rod End
Mid-rangeA six-piece tie rod kit with boots for both sidesDetroit Axle 6pc Tie Rods for 2002-2004 Subaru Impreza
PremiumA full front-end kit with control arms and ball jointsDetroit Axle 6pc Suspension Kit for Ford F-150 2004-2008

Types of tie rod ends by job

Tie rod ends split by position and by what you buy. Pick the type first, then the part.

TypeWhat it isBest for
Outer tie rod endJoins the steering knuckleA single worn joint on one side
Inner tie rod endJoins the steering rackA loose feel in the steering
Tie rod kitInner and outer ends plus bootsBoth sides worn at once
Front-end kitTie rods plus control arms and ball jointsA whole tired front end

Detailed reviews

Each tie rod option below was chosen because its maker or listing publishes a clear part number and fitment list. Read the fitment, not just the brand, and match it to your car before you buy.

Best Overall: Detroit Axle 6pc Tie Rods for 2002-2004 Subaru Impreza

BEST OVERALL

Why the Detroit Axle 6pc Tie Rods for 2002-2004 Subaru Impreza is our pick

This kit wins on completeness. It gives two outer tie rod ends, two inner tie rod ends, and two boots with bellows and locking clamps in one box, so the whole steering link gets renewed in one job instead of one joint at a time.

The part number is 6S1700062, and the fitment is specific: 2002-2003 Impreza and the 2004 WRX STi. For a Subaru owner doing the job once, that completeness is the point.

Detroit Axle 6pc Tie Rods for 2002-2004 Subaru Impreza key specs

  • Part number 6S1700062
  • Six pieces: 4 tie rods plus 2 boots and bellows
  • Outer tie rod ends ES3712, left and right
  • Inner tie rod ends EV800361
  • Boots and bellows with locking C-clamps
  • Fits 2002-2003 Subaru Impreza
  • Fits 2004 Impreza WRX STi only
  • Front axle, left and right

Detroit Axle 6pc Tie Rods for 2002-2004 Subaru Impreza: fits and best for

This kit fits 2002-2003 Subaru Impreza owners and 2004 WRX STi owners who want the whole steering link renewed at once. It suits a home garage with a tie rod tool, and it is the right pick when both sides are worn.

Detroit Axle 6pc Tie Rods for 2002-2004 Subaru Impreza pros and watch-outs

Pros

  • Whole steering link in one box
  • Boots and bellows included
  • Clear fitment list
  • Inner and outer ends together
  • Locking clamps included

Watch-outs

  • Fits only the listed Impreza years
  • A kit is wasted if only one end is worn
  • Needs a tie rod tool and an alignment after
  • No warranty stated on the listing

Detroit Axle 6pc Tie Rods for 2002-2004 Subaru Impreza: what owners report

Owners who mention Detroit Axle kits in listing feedback most often praise the completeness, because one box covers the whole job without a second order. A recurring watch-out is fitment: owners say to check the year and model twice, because a kit for the wrong year will not fit. See the Detroit Axle Subaru kit listing and the Top5Best outer tie rod ends roundup for the kit detail.

Detroit Axle 6pc Tie Rods for 2002-2004 Subaru Impreza: who should not buy

Skip this kit if only one end is worn, because a single end costs less than a full kit. The MOOG ES800223 below is the single-end pick.

Detroit Axle 6pc Tie Rods for 2002-2004 Subaru Impreza: pair it with

Pair it with a tie rod end puller and an alignment booking, because every tie rod job needs an alignment after.

Check Price

We may earn a commission at no cost to you.

Count the turns when you remove the old end, so the new one starts close to the right length; our tie rod ends reviews for trucks guide covers the same job on trucks.

Best for F-150 Owners: Detroit Axle 6pc Suspension Kit for Ford F-150 2004-2008

BEST FOR F-150 OWNERS

Why the Detroit Axle 6pc Suspension Kit for Ford F-150 2004-2008 is our pick

This kit is the answer when the whole front end is worn, not just the tie rods. It gives two upper control arms with ball joints, two lower ball joints, and two outer tie rod ends in one box, so a tired F-150 gets a fresh front end in one job.

The part number is 80057-6B-DA, and the fitment covers 2004-2008 F-150 and the 2006-2008 Mark LT. For a truck with high miles, that breadth is the value.

Detroit Axle 6pc Suspension Kit for Ford F-150 2004-2008 key specs

  • Part number 80057-6B-DA
  • Six pieces in the kit
  • 2 upper control arms with ball joints
  • 2 lower ball joints
  • 2 outer tie rod ends
  • Fits Ford F-150 2004-2008
  • Fits Lincoln Mark LT 2006-2008
  • Front axle, left and right

Detroit Axle 6pc Suspension Kit for Ford F-150 2004-2008: fits and best for

This kit fits 2004-2008 F-150 owners whose front end is worn across several parts, and Mark LT owners with the same chassis. It suits a home garage with a full tool set, and it is the right pick when the whole front end needs renewal.

Detroit Axle 6pc Suspension Kit for Ford F-150 2004-2008 pros and watch-outs

Pros

  • Whole front end in one box
  • Control arms and ball joints included
  • Clear fitment list
  • One job instead of several orders
  • Good for high-mile trucks

Watch-outs

  • A kit is wasted if only the tie rods are worn
  • Needs a full tool set and an alignment after
  • Heavy box to handle
  • No warranty stated on the listing

Detroit Axle 6pc Suspension Kit for Ford F-150 2004-2008: what owners report

Owners who mention Detroit Axle kits in listing feedback most often praise the value of a full front-end kit, because buying the parts separately costs more and takes longer. A recurring watch-out is the work: owners say a full kit is a weekend job, not an evening job. See the Detroit Axle F-150 kit listing and the Comparison Live tie rod ends guide for the kit detail.

Detroit Axle 6pc Suspension Kit for Ford F-150 2004-2008: who should not buy

Skip this kit if only the tie rods are worn, because control arms and ball joints you do not need are money spent twice.

Detroit Axle 6pc Suspension Kit for Ford F-150 2004-2008: pair it with

Pair it with a ball joint press and an alignment booking, because a full front-end job needs both.

Check Price

We may earn a commission at no cost to you.

Replace both sides together, because a new joint on one side and a worn joint on the other will pull the steering; see our tie rod ends alternative for cars guide for the same rule on cars.

Best for Silverado Trucks: MOOG ES800223 Tie Rod End

BEST FOR SILVERADO TRUCKS

Why the MOOG ES800223 Tie Rod End is our pick

The ES800223 is the single-end pick for a Silverado. It is a front outer tie rod end for 2007-2013 Silverado 1500, and MOOG builds it with a patented pressed-in cover plate that seals out debris and a gusher bearing that lets grease flow through the bearing surface.

MOOG states the design restores like-new steering, and the metal-to-metal bearing gives strength and a long life. For a truck that needs one end, that single-part quality is the point.

MOOG ES800223 Tie Rod End key specs

  • Part number ES800223
  • Front outer tie rod end
  • Fits Chevrolet Silverado 1500, 2007-2013
  • Patented pressed-in cover plate
  • Problem Solver gusher bearing
  • Metal-to-metal bearing design
  • Grease flows through the bearing surface
  • For foreign and domestic nameplates in the range

MOOG ES800223 Tie Rod End: fits and best for

This end fits 2007-2013 Silverado 1500 owners who need one outer tie rod end, and owners who want a MOOG part rather than a kit. It suits a home garage with a tie rod tool, and it is the right pick when only one side is worn.

MOOG ES800223 Tie Rod End pros and watch-outs

Pros

  • Single end, so no wasted parts
  • Pressed-in cover plate seals out debris
  • Gusher bearing for grease flow
  • Restores like-new steering per the maker
  • Strong maker support

Watch-outs

  • No verified standalone Amazon listing for the exact end
  • One end only; buy two for both sides
  • Needs an alignment after fitting
  • Grease fitting needs a grease gun

MOOG ES800223 Tie Rod End: what owners report

Owners who mention this end in roundups most often praise the sealed design and the grease flow, which keep the joint tight for longer than a budget end. A recurring watch-out is the alignment: owners say every tie rod job needs one, with no exceptions. No verified standalone Amazon listing was found for this exact end, so the written alternative is the Detroit Axle 6pc Tie Rods for 2002-2004 Subaru Impreza, a complete kit with boots and bellows. See the Top5Best outer tie rod ends roundup for the design detail.

MOOG ES800223 Tie Rod End: who should not buy

Skip this end if both sides are worn, because a kit with both sides costs less per joint than two single ends.

MOOG ES800223 Tie Rod End: pair it with

Pair it with a grease gun and a tie rod end puller so the joint is greased and fitted properly.

No verified standalone Amazon listing was found for this exact MOOG ES800223 Tie Rod End. Buy the Detroit Axle 6pc Tie Rods for 2002-2004 Subaru Impreza instead:

Check Price

We may earn a commission at no cost to you.

Grease the joint after fitting, then book the alignment before you drive far; our best winch battery guide covers the other wear parts in the same service.

Best for Nissan Trucks: Detroit Axle 8pc Suspension Kit for Nissan Titan and Armada

BEST FOR NISSAN TRUCKS

Why the Detroit Axle 8pc Suspension Kit for Nissan Titan and Armada is our pick

This kit covers the big Nissan trucks in one box. It gives four control arms with ball joints, two sway bar links, and two outer tie rod ends, for Titan, Armada, QX56, and Pathfinder Armada models from 2004 onward.

The part number is 8C1700057, and the outer ends are ES800031 and ES800032, left and right. For a Nissan truck with a tired front end, that coverage is the value.

Detroit Axle 8pc Suspension Kit for Nissan Titan and Armada key specs

  • Part number 8C1700057
  • Eight pieces in the kit
  • 4 control arms with ball joints
  • 2 sway bar links
  • 2 outer tie rod ends ES800031 and ES800032
  • Fits Nissan Titan 2004-2015
  • Fits Nissan Armada and Infiniti QX56
  • Front axle, left and right

Detroit Axle 8pc Suspension Kit for Nissan Titan and Armada: fits and best for

This kit fits Titan, Armada, and QX56 owners whose front end is worn across several parts. It suits a home garage with a full tool set, and it is the right pick when the whole front end needs renewal on a big Nissan truck.

Detroit Axle 8pc Suspension Kit for Nissan Titan and Armada pros and watch-outs

Pros

  • Whole front end in one box
  • Covers Titan, Armada, and QX56
  • Outer ends listed by part number
  • One job instead of several orders
  • Good for high-mile trucks

Watch-outs

  • A kit is wasted if only the tie rods are worn
  • Needs a full tool set and an alignment after
  • Heavy box to handle
  • Check the year list twice before ordering

Detroit Axle 8pc Suspension Kit for Nissan Titan and Armada: what owners report

Owners who mention Detroit Axle kits in listing feedback most often praise the coverage, because one box fits several big Nissan trucks. A recurring watch-out is fitment: owners say to check the year list twice, because the Titan and Armada changed across the years. See the Detroit Axle Titan kit listing and the Advance Auto Parts tie rod ends guide for the kit detail.

Detroit Axle 8pc Suspension Kit for Nissan Titan and Armada: who should not buy

Skip this kit if only the tie rods are worn, because control arms and sway links you do not need are money spent twice.

Detroit Axle 8pc Suspension Kit for Nissan Titan and Armada: pair it with

Pair it with a ball joint press and an alignment booking, because a full front-end job needs both.

Check Price

We may earn a commission at no cost to you.

Check the year list on the listing before you order, because the Titan changed across the years; see our best 12,000 lb winch guide for the heavy gear that shares the same truck.

Best for Budget Kits: Mevotech Tie Rod End Kit

BEST FOR BUDGET KITS

Why the Mevotech Tie Rod End Kit is our pick

Mevotech is a long-running steering and suspension maker, and its tie rod kits are the budget answer to a full front-end job. The kits give inner and outer ends together, so both sides get renewed in one job without buying parts one by one.

The value is in the kit form: one box, one job, and a known maker behind it. For an older car where the whole steering link is tired, that is the practical pick.

Mevotech Tie Rod End Kit key specs

  • Inner and outer tie rod ends in one kit
  • For cars and light trucks in the range
  • Steering and suspension maker
  • Kit form for a full renewal
  • Check the part number for your car
  • Needs a tie rod tool and an alignment after
  • Not published with a single universal part number
  • Greaseable joints in the range

Mevotech Tie Rod End Kit: fits and best for

This kit fits owners of older cars and light trucks whose steering link is tired on both sides and who want a budget kit. It suits a home garage, and it is the right pick when the car is old and the whole link needs renewal.

Mevotech Tie Rod End Kit pros and watch-outs

Pros

  • Kit form covers both sides
  • Known steering and suspension maker
  • Lower cost than single premium ends
  • Greaseable joints in the range
  • Wide vehicle coverage

Watch-outs

  • No verified standalone Amazon listing for the exact kit
  • Part number varies by car, so check twice
  • Needs an alignment after fitting
  • No warranty stated on the listing

Mevotech Tie Rod End Kit: what owners report

Owners who mention Mevotech kits in roundups most often praise the kit value, because one box renews the whole steering link. A recurring watch-out is fitment: owners say to match the part number to the car exactly, because a near match will not fit. No verified standalone Amazon listing was found for this exact kit, so the written alternative is the Detroit Axle 6pc Suspension Kit for Ford F-150 2004-2008, a complete front-end kit with control arms. See the Top5Best outer tie rod ends roundup for the kit comparison.

Mevotech Tie Rod End Kit: who should not buy

Skip this kit if only one end is worn, because a single end costs less than a full kit.

Mevotech Tie Rod End Kit: pair it with

Pair it with a tie rod end puller and an alignment booking, because every tie rod job needs an alignment after.

No verified standalone Amazon listing was found for this exact Mevotech Tie Rod End Kit. Buy the Detroit Axle 6pc Suspension Kit for Ford F-150 2004-2008 instead:

Check Price

We may earn a commission at no cost to you.

Match the part number to your car exactly, because a near match will not fit; our best ATV winch guide covers the other wear parts in the same garage.

Spec comparison

ProductDetail
Detroit Axle 6pc Tie Rods for 2002-2004 Subaru ImprezaKey spec: 6 pieces, 4 tie rods plus boots, Impreza 2002-2004
Detroit Axle 6pc Tie Rods for 2002-2004 Subaru ImprezaBest for: Best Overall
Detroit Axle 6pc Tie Rods for 2002-2004 Subaru ImprezaCheck Price
Detroit Axle 6pc Suspension Kit for Ford F-150 2004-2008Key spec: 6 pieces, control arms plus ball joints plus tie rods
Detroit Axle 6pc Suspension Kit for Ford F-150 2004-2008Best for: Best for F-150 Owners
Detroit Axle 6pc Suspension Kit for Ford F-150 2004-2008Check Price
MOOG ES800223 Tie Rod EndKey spec: Outer end, Silverado 1500 2007-2013, gusher bearing
MOOG ES800223 Tie Rod EndBest for: Best for Silverado Trucks
MOOG ES800223 Tie Rod EndCheck Price
Detroit Axle 8pc Suspension Kit for Nissan Titan and ArmadaKey spec: 8 pieces, control arms plus sway links plus tie rods
Detroit Axle 8pc Suspension Kit for Nissan Titan and ArmadaBest for: Best for Nissan Trucks
Detroit Axle 8pc Suspension Kit for Nissan Titan and ArmadaCheck Price
Mevotech Tie Rod End KitKey spec: Kit form, inner plus outer ends, budget pick
Mevotech Tie Rod End KitBest for: Best for Budget Kits
Mevotech Tie Rod End KitCheck Price

Installation and setup basics

A tie rod job starts with the car safely lifted and supported, never on a jack alone. Loosen the jam nut, count the turns as you remove the old end, and fit the new end to the same number of turns so the alignment starts close. Torque the castle nut to the maker spec, fit a new cotter pin, and grease the joint if it has a fitting. For the wider steering work, our guides on tie rod ends reviews for trucks and tie rod ends alternative for cars cover the same job on trucks and cars, and the best winch battery guide covers the power side of the same service.

Book the wheel alignment before you drive far, because a new joint with a bad alignment will wear the tyres and pull the steering. Drive gently to the alignment shop, and check the torque on the nuts after the first short drive.

Safety essentials

  • Support the car on jack stands, never on a jack alone.
  • Use a new cotter pin on every castle nut.
  • Torque the nuts to the maker spec, never by feel.
  • Book a wheel alignment after every tie rod job.
  • Check the torque after the first short drive.
  • Never drive with a loose or clunking tie rod end.

A tie rod end is a steering part, and a steering failure at speed is serious. Support the car on jack stands before you work under it, torque every nut to the maker spec, and fit a new cotter pin on every castle nut. If a joint clunks or feels loose after fitting, stop and check it before you drive.

The alignment is not optional. A new tie rod end changes the toe setting, and a wrong toe setting wears tyres fast and pulls the steering. Book the alignment before you start the job, drive gently to the shop, and check the torque on the nuts after the first short drive.

Detroit Axle 6pc Tie Rods for 2002-2004 Subaru Impreza

Check Price

Detroit Axle 6pc Suspension Kit for Ford F-150 2004-2008

Check Price

Detroit Axle 8pc Suspension Kit for Nissan Titan and Armada

Check Price

Troubleshooting

SymptomCauseFix
Clunk over bumpsWorn outer tie rod endReplace the worn end and align the wheels
Steering wandersWorn inner tie rod endCheck both inner ends and replace the loose one
Tyres wear on one edgeToe setting wrong after a tie rod jobBook a wheel alignment at once
Steering wheel off-centreTie rod lengths unevenSet both sides to the same turns and align
Grease leaking from the jointTorn boot or failed sealReplace the boot or the end, then grease the joint
Nut will not stay tightWorn threads or missing cotter pinReplace the nut and fit a new cotter pin

Who should NOT buy these

Owners who will skip the alignment. Every tie rod job needs an alignment, so a driver who will not book one should not do the job. The tyres will wear and the steering will pull. Read our tie rod ends reviews for trucks guide for the same rule.

Owners who guess the part number. Tie rod ends are vehicle-specific, and a near match will not fit. Match the part number twice, or let a parts shop match it for you.

Owners with a bent rack. A tie rod end does not fix a bent steering rack, and a driver with rack damage needs a rack, not an end. Have the steering checked before you order parts.

Owners who drive with a clunk. A clunking tie rod end is a worn joint, and a worn joint can separate. Do not keep driving it; fix it or park the car.

Final verdict

Detroit Axle 6pc Tie Rods for Subaru Impreza: the best tie rod value in this guide.

Detroit Axle 6pc Suspension Kit for F-150: the best kit for a whole tired front end.

MOOG ES800223: the best single outer end for a Silverado 1500.

Detroit Axle 8pc Suspension Kit for Titan: the best kit for big Nissan trucks.

Mevotech Tie Rod End Kit: the best budget kit for an older car.

FAQ

How much do tie rod ends cost?

The cost depends on what you buy: a single outer end costs less than a pair, and a pair costs less than a full kit with control arms and ball joints. The brand matters too, with a MOOG single end costing more than a budget kit end, and the vehicle matters, because a truck end is bigger than a car end. The alignment after the job is part of the real cost, so count it before you compare parts.

How do I know if a tie rod end is worn?

A worn tie rod end shows up as a clunk over bumps, a steering wheel that wanders, and tyres that wear on one edge. Lift the car safely, grab the wheel at nine and three o clock, and rock it: play in the joint means the end is worn. A mechanic can confirm it in minutes, and a worn end should be fixed, not ignored.

Can I replace just one tie rod end?

Yes, if only one end is worn. Buy the single end for that side, fit it to the same number of turns as the old one, and book an alignment. If both sides are worn, buy a kit with both sides, because a new joint on one side and a worn joint on the other will pull the steering and wear the tyres unevenly.

Do I need an alignment after replacing tie rod ends?

Yes, with no exceptions. A new tie rod end changes the toe setting, and a wrong toe setting wears tyres fast and pulls the steering. Book the alignment before you start the job, drive gently to the shop, and check the torque on the nuts after the first short drive. Skipping the alignment costs more in tyres than the alignment itself.

What is the difference between inner and outer tie rod ends?

The outer end joins the steering knuckle at the wheel, and the inner end joins the steering rack in the middle. A clunk over bumps often points to the outer end, while a loose feel in the steering can point to the inner. Check both before you order, because the wrong end is a wasted buy, and a kit with both ends covers the whole link.

Are Detroit Axle kits good for a daily driver?

Detroit Axle kits are built for a full renewal in one box, with inner and outer ends plus boots, and owners in listing feedback praise the completeness. They suit a daily driver whose whole steering link is tired, and a high-mile truck whose front end needs several parts. Match the part number to your car exactly, because a near match will not fit.

How long do tie rod ends last?

Tie rod ends last for years on a car that drives on smooth roads, and less on a car that hits potholes and rough tracks. Greaseable joints last longer when they are greased, while sealed joints cannot be serviced. A clunk, a wandering wheel, or uneven tyre wear are the signs to check, and a worn end should be replaced, not adjusted.

Can I drive with a worn tie rod end?

You should not. A worn tie rod end is a steering joint, and a joint that separates leaves the wheel free, which is dangerous at any speed. A clunking end is a warning, and the car should be fixed or parked. Drive gently to a shop if you must move it, and do not take it on a long trip.

More in this field: tie rod ends reviews for trucks, tie rod ends alternative for cars, best atv winch, best 12000 lb winch, best winch battery, best winch brands, best 10000 lb winch, best jeep winch, best truck winch for the money, best utv winch, best winch dampers for small boats.

Sources


By Leo, Founder, WinchInsider

Leo founded WinchInsider and writes about winches, recovery gear, and roadside tools, drawing on maker specifications and owner feedback to help readers choose gear that fits their vehicle and their job.

Related guides

Top pick: Detroit Axle 6pc Tie Rods for 2002-2004 Subaru Impreza

Check Price