Your steering feels loose, the front tyres wear on the inside edge, and every bump sends a clunk through the wheel. Worn tie rod ends cause all three, and they are one of the most common reasons a car fails an alignment check.
The dealer part costs a lot, so most owners look for an alternative. This guide compares four tie rod end alternatives for cars, from single MOOG ends to full Detroit Axle kits, so you can match the part to your car and your budget without guessing at fitment.
The 30-second answer
The best tie rod end alternative for most cars is the MOOG ES800223 outer tie rod end. It is a greasable, problem-solver design with a strong aftermarket record on GM trucks and SUVs. For a full front-end refresh, the Detroit Axle 6-piece kit covers both sides in one box. The MOOG EV800085 is the inner end for the Camry, and the Detroit Axle Camry kit covers the most common sedan in the same way.
How we researched this guide
For this guide we compared 4 tie rod end alternatives against the manufacturers’ own part numbers and fitment data (MOOG and Detroit Axle). We then read owner reports on the Amazon listings for each part, plus fitment guides, to check which vehicles each part actually fits. Every spec below comes from a published source, and every source is listed at the bottom of this page.
Where a manufacturer does not publish a spec, we say so instead of guessing.
BEST OVERALL
MOOG ES800223 Outer Tie Rod End
A greasable outer tie rod end for 2007-2013 Silverado 1500 and related GM trucks and SUVs. The problem-solver pick.
BEST FULL KIT
Detroit Axle 6-Piece Front Tie Rods Kit 1999-2006 Silverado 1500
A 6-piece front tie rod kit for 1999-2006 Silverado 1500 trucks. Both sides, inner and outer, in one box.
BEST INNER END
MOOG EV800085 Inner Tie Rod End for Toyota Camry
A MOOG inner tie rod end for the Toyota Camry. The rack-side part for Camry steering refreshes.
BEST FOR SEDANS
Detroit Axle 8-Piece Front Suspension Kit for 1992-1996 Camry
An 8-piece front suspension kit for 1992-1996 Toyota Camry, 1995-1996 Avalon and 1992-1996 Lexus ES300. The sedan alternative to the truck kits.
| Product | Type | Fits | Warranty | |
|---|---|---|---|---|
| MOOG ES800223 Outer Tie Rod End | Greasable | GM 2007-2013 | Single end | |
| Detroit Axle 6-Piece Front Tie Rods Kit 1999-2006 Silverado 1500 | Full kit | Silverado 1999-2006 | 6 pieces | |
| MOOG EV800085 Inner Tie Rod End for Toyota Camry | Inner end | Inner, rack side | Not published | |
| Detroit Axle 8-Piece Front Suspension Kit for 1992-1996 Camry | Full kit | Camry 1992-1996 | 8-piece set |
Tie rod end chooser
Enter your vehicle weight in lb as a rough guide to the class of part you need, then confirm fitment by year, make and model before ordering.
How to choose tie rod ends for your car
Start with fitment, then look at design, warranty and whether you need one end or a kit. These six points decide whether the part fits and lasts.
Fitment first, always
Tie rod ends are vehicle-specific: thread size, taper and length change between models and even between model years. The MOOG ES800223 fits 2007-2013 GM trucks, the Detroit Axle kits fit their listed years, and the MOOG EV800085 is an inner end for the Camry. Check year, make, model and side against the listing before you order anything.
Inner or outer
Outer tie rod ends connect to the steering knuckle and wear first, because they move the most. Inner ends connect to the steering rack and last longer. If only the outer end is loose, buy the single end. If both are worn, a kit that covers inner and outer ends on both sides is the better buy.
Greasable or sealed
Greasable ends, like the MOOG pick, have a grease fitting you service at every oil change. Sealed ends need no maintenance but cannot be serviced once the grease inside wears out. Greasable ends last longer in the hands of an owner who maintains them; sealed ends suit owners who never touch the car.
Single end or full kit
A single end is the cheapest fix for one worn joint. A kit is the better buy when both sides are worn, which is common on high-mileage cars. Our guide to the alternatives to the best wrench sets for mechanics covers the tools for either job.
Warranty
None of the four picks publishes warranty terms on its listing, so compare them on fitment and design instead of cover. That does not mean the parts fail, but it does mean you have less to fall back on if one does, so check the listing for the current terms before you order.
Alignment after fitting
Every tie rod end change needs a wheel alignment afterwards. The new end will not sit in exactly the same place as the old one, and even a small difference wears tyres unevenly. Budget for the alignment as part of the job, not as an optional extra.
Tie rod ends by budget
| Budget tier | What you get | Example pick |
|---|---|---|
| Budget | Single aftermarket end for one side | MOOG ES800223 |
| Mid-range | Full front kit for both sides | Detroit Axle Camry kit |
| Premium | Inner end for the Camry | MOOG EV800085 |
Types of tie rod ends
| Choice | Pros | Cons | Best for |
|---|---|---|---|
| Outer tie rod end | Wears first, easy to reach, cheap to replace | Needs alignment after fitting | Most tie rod jobs |
| Inner tie rod end | Lasts longer, fewer replacements | Harder to reach, needs a special tool | Full front-end refreshes |
| Full tie rod kit | Both sides in one box, one job | Overkill for a single worn end | High-mileage cars |
| OE-brand end | Exact fit, longest warranty | Sold singly, costs more per end | Owners who want OE quality |
Detailed reviews of the best tie rod ends alternatives for cars
Each pick below follows the same format: verified specs first, then owner reports with sources. If you also need the tools for the job, see our guide to the adjustable wrenches reviews and best brands.
Best Overall: MOOG ES800223 Outer Tie Rod End
Best Overall
For owners who want the strongest aftermarket tie rod end for a GM truck or SUV.
Why the MOOG ES800223 Outer Tie Rod End is our pick
The MOOG ES800223 is the reference aftermarket outer tie rod end for 2007-2013 Silverado 1500, Escalade, Avalanche, Sierra 1500, Suburban, Tahoe and Yukon models. It is greasable, with a design MOOG calls its problem-solver line, and it replaces ACDelco 45A1092 and GM part 15254061.
Check fitment by year, make and model before ordering, because this part number covers a specific GM range and nothing else.
MOOG ES800223 Outer Tie Rod End key specs
- Part number: ES800223
- Position: front outer, driver or passenger side
- Fits: 2007-2013 Silverado 1500, Escalade, Avalanche, Sierra 1500, Suburban 1500, Tahoe, Yukon
- Design: greasable, problem-solver line per MOOG
- Replaces: ACDelco 45A1092, GM 15254061
- Interchange: Mevotech MES800223, Dorman 534-835
- Thread: matches the original outer tie rod thread for the listed vehicles
- Grease fitting: included per the maker design
- Sold as: single outer tie rod end
- Use: steering, front outer position
- Warranty: not published on the listing
- Best for: GM trucks and SUVs
MOOG ES800223 Outer Tie Rod End: fits and best for
2007-2013 GM full-size trucks and SUVs: Silverado 1500, Sierra 1500, Tahoe, Suburban 1500, Yukon, Escalade and Avalanche. Confirm your exact year and trim before ordering.
MOOG ES800223 Outer Tie Rod End pros and watch-outs
Pros
- Greasable design you can service at every oil change
- Direct replacement for ACDelco 45A1092 and GM 15254061
- Strong aftermarket record on GM trucks and SUVs
- Fits both driver and passenger sides
- Problem-solver design per MOOG
Watch-outs
- Covers one GM range only; check fitment carefully
- Sold singly, so a pair costs double
- Needs an alignment after fitting
MOOG ES800223 Outer Tie Rod End: what owners report
- Owner reviews on the Amazon listing praise the tight fit and the grease fitting, and note the steering feels tighter after the swap.
- The recurring owner note is fitment: buyers who skip the year and model check sometimes order the wrong side or the wrong generation, so confirm the application first.
MOOG ES800223 Outer Tie Rod End: who should not buy
Skip it if your car is not a 2007-2013 GM truck or SUV. This part number fits that range only, and forcing it onto another vehicle is not an alternative, it is a mistake. Use the Detroit Axle kits below for other cars.
MOOG ES800223 Outer Tie Rod End: pair it with
A pair, one for each side, plus a fresh alignment. Our guide to the MOOG tie rod ends review covers the brand in more depth.
We may earn a commission at no cost to you.
Tip: Count the turns when you unscrew the old end. Fitting the new end to the same number of turns gets the alignment close enough to drive to the alignment shop safely.
Best Full Kit: Detroit Axle 6-Piece Front Tie Rods Kit 1999-2006 Silverado 1500
Best Full Kit
For owners refreshing the whole front steering on an older Silverado in one job.
Why the Detroit Axle 6-Piece Front Tie Rods Kit 1999-2006 Silverado 1500 is our pick
The Detroit Axle 6-piece kit covers the full front tie rod set for 1999-2006 Silverado 1500 trucks: inner and outer ends for both sides, plus the parts that connect them. Buying the kit beats buying ends one at a time when the whole front end is worn.
As with every tie rod part, confirm the year range matches your truck before ordering.
Detroit Axle 6-Piece Front Tie Rods Kit 1999-2006 Silverado 1500 key specs
- Part number: 80416-6A
- Fits: 1999-2006 Silverado 1500
- Kit contents: 6-piece front tie rod set, both sides
- Positions: inner and outer, driver and passenger
- Design: direct replacement for the original parts
- Sold as: complete 6-piece kit
- Use: steering, full front tie rod refresh
- Install: alignment required after fitting
- Grease fittings: per the kit design
- Warranty: not published on the listing
- Best for: older Silverado trucks
- Note: confirm your exact year and model before ordering
Detroit Axle 6-Piece Front Tie Rods Kit 1999-2006 Silverado 1500: fits and best for
1999-2006 Chevrolet Silverado 1500 trucks. It suits owners doing a full front-end refresh rather than a single worn end.
Detroit Axle 6-Piece Front Tie Rods Kit 1999-2006 Silverado 1500 pros and watch-outs
Pros
- Full front set in one box, both sides
- Cheaper than buying ends one at a time
- Direct replacement for the original parts
- One job covers the whole front steering
- Suits high-mileage trucks with wear on both sides
Watch-outs
- Fits one truck range only
- A full kit is overkill if only one end is worn
- Needs an alignment after fitting
Detroit Axle 6-Piece Front Tie Rods Kit 1999-2006 Silverado 1500: what owners report
- Owner reviews on the Amazon listing describe the kit as a complete fix for loose steering on older Silverados, with the inner and outer ends fitting as expected.
- The recurring owner note is to replace both sides together: doing one side and leaving a worn end on the other side leaves the steering loose.
Detroit Axle 6-Piece Front Tie Rods Kit 1999-2006 Silverado 1500: who should not buy
Skip it if only one tie rod end is worn and the rest of the front end is tight. Buy the single end you need instead, and save the kit for a full refresh.
Detroit Axle 6-Piece Front Tie Rods Kit 1999-2006 Silverado 1500: pair it with
A fresh alignment and a check of the ball joints while the front end is apart. Our guide to the Mevotech tie rod ends review covers another aftermarket option for the same trucks.
We may earn a commission at no cost to you.
Tip: Replace the inner and outer ends on both sides at the same time. Mixed old and new ends wear unevenly and pull the alignment out faster.
Best Inner End: MOOG EV800085 Inner Tie Rod End for Toyota Camry
Best Inner End
For Camry owners who need the inner end, not the outer one.
Why the MOOG EV800085 Inner Tie Rod End for Toyota Camry is our pick
The MOOG EV800085 is the inner tie rod end for the Toyota Camry, and it fills the gap the outer ends leave: when the inner joint wears, the steering goes loose even with new outer ends fitted. It is the MOOG part for the rack side of the job rather than the knuckle side.
The trade-off is the fitting: an inner end sits on the steering rack, and you need a special tool to reach it. For a Camry with play at the rack, though, it is the right part.
MOOG EV800085 Inner Tie Rod End for Toyota Camry key specs
- Part number: EV800085
- Position: front inner, rack side
- Fits: Toyota Camry per the listing
- Brand: MOOG Chassis Products
- Design: inner tie rod end, direct replacement
- Sold as: single inner tie rod end
- Use: steering, front inner position
- Install: alignment required after fitting
- Warranty: not published on the listing
- Best for: Camry steering refreshes
MOOG EV800085 Inner Tie Rod End for Toyota Camry: fits and best for
Toyota Camry owners whose steering play comes from the rack side, not the outer joint. Confirm your exact year, make and model against the part listing before ordering.
MOOG EV800085 Inner Tie Rod End for Toyota Camry pros and watch-outs
Pros
- MOOG aftermarket part for Camry steering
- Fixes play that new outer ends cannot fix
- Direct replacement for the original inner end
- Single part, so you buy exactly what you need
- MOOG chassis range, widely stocked
Watch-outs
- Harder to fit than an outer end
- Needs a special inner tie rod tool
- Needs an alignment after fitting
MOOG EV800085 Inner Tie Rod End for Toyota Camry: what owners report
- Owner reviews on the Amazon listing describe the EV800085 as a direct-fit inner end for the Camry, with the steering tightening up once the rack-side play is gone.
- The recurring owner note is the tool: buyers who fit it with an inner tie rod tool finish the job cleanly, and buyers who improvise struggle to reach it.
MOOG EV800085 Inner Tie Rod End for Toyota Camry: who should not buy
Skip it if only the outer end is loose. The inner end sits on the rack, and replacing it will not fix play at the knuckle. Check which joint is worn before you order.
MOOG EV800085 Inner Tie Rod End for Toyota Camry: pair it with
An inner tie rod tool and a fresh alignment. Our guide to the adjustable wrenches reviews and best brands covers the tools for the job.
We may earn a commission at no cost to you.
Tip: Check the inner joint for play before you order outer ends. Hold the rack end still and rock the wheel: movement at the rack means the inner end is the worn one.
Best for Sedans: Detroit Axle 8-Piece Front Suspension Kit for 1992-1996 Camry
Best for Sedans
For older Camry owners who want the full front set in one box.
Why the Detroit Axle 8-Piece Front Suspension Kit for 1992-1996 Camry is our pick
The Detroit Axle 8-piece kit covers the front suspension for 1992-1996 Toyota Camry, 1995-1996 Avalon and 1992-1996 Lexus ES300 models: 2 lower ball joints, 2 sway bar end links and 4 inner and outer tie rod ends.
Sedans wear tie rod ends just like trucks do, and the symptoms are the same: loose steering, uneven tyre wear and a clunk over bumps. A kit that fits your exact model year takes the guesswork out of ordering.
Detroit Axle 8-Piece Front Suspension Kit for 1992-1996 Camry key specs
- Part number: 80004-8A
- Fits: 1992-1996 Toyota Camry, 1995-1996 Avalon, 1992-1996 Lexus ES300
- Kit contents: 8-piece front suspension set
- Includes: 2 lower ball joints, 2 sway bar end links, 4 inner and outer tie rod ends
- Positions: front, driver and passenger
- Design: direct replacement for the original parts
- Sold as: complete kit
- Use: steering, front suspension refresh
- Install: alignment required after fitting
- Warranty: not published on the listing
- Best for: older Camry, Avalon and ES300 sedans
- Note: confirm your exact year and model before ordering
Detroit Axle 8-Piece Front Suspension Kit for 1992-1996 Camry: fits and best for
1992-1996 Toyota Camry, 1995-1996 Avalon and 1992-1996 Lexus ES300 sedans. It suits high-mileage sedans with loose steering.
Detroit Axle 8-Piece Front Suspension Kit for 1992-1996 Camry pros and watch-outs
Pros
- Fits the most common sedans of its era
- Full front set in one box
- Direct replacement for the original parts
- One job covers both sides
- Cheaper than buying ends one at a time
Watch-outs
- Fits a narrow year range only
- A full kit is overkill for a single worn end
- Needs an alignment after fitting
Detroit Axle 8-Piece Front Suspension Kit for 1992-1996 Camry: what owners report
- Owner reviews on the Amazon listing describe the kit as a straightforward fix for loose steering on older Camrys, with the parts fitting as listed.
- The recurring owner note is the alignment: owners who skip it after fitting report the car pulling to one side until the alignment is done.
Detroit Axle 8-Piece Front Suspension Kit for 1992-1996 Camry: who should not buy
Skip it if your Camry is not a 1992 to 1996 model. Tie rod ends change between generations, and a close fit is not a fit.
Detroit Axle 8-Piece Front Suspension Kit for 1992-1996 Camry: pair it with
A fresh alignment and a tyre rotation while the car is on the lift. Our guide to the best adjustable torque wrench covers the torque tool for the job.
We may earn a commission at no cost to you.
Tip: Get the alignment done the same day you fit the kit. Driving even a week on a bad alignment wears the new ends unevenly.
Spec comparison
| Spec | MOOG ES800223 | Detroit Axle Silverado Kit | MOOG EV800085 | Detroit Axle Camry Kit |
|---|---|---|---|---|
| Type | Outer tie rod | Full front kit | Inner tie rod | Front tie rod kit |
| Fits | GM 2007-2013 | Silverado 1999-2006 | Camry, inner end | Camry 1992-1996, Avalon, ES300 |
| Material | Steel, greasable | Steel, direct replacement | Steel, direct replacement | Steel, direct replacement |
| Install | Threaded, alignment after | Full refresh, alignment after | Threaded, alignment after | Full refresh, alignment after |
| Grease fitting | Grease fitting included | Kit includes inner and outer | No grease fitting; inner end | Kit includes front set |
| Range | MOOG chassis range | Detroit Axle steering range | MOOG chassis range | Detroit Axle steering range |
| Position | GM trucks and SUVs | Silverado 1500 trucks | Camry, rack side | Camry, Avalon and ES300 |
| Warranty | Not published | Not published | Not published | Not published |
| Best for | GM trucks and SUVs | Full front refresh | Camry steering refresh | Sedans |
| Check Price |
How to read this table: the rows below are the makers' published figures and our editorial judgement, not test results. Where a maker does not publish a figure, the cell says Not published rather than guessing.
Compare the rows above on the makers' published figures, and confirm fitment for your exact vehicle before ordering.
Installation & wiring basics
Every tie rod end here follows the same basic install. Loosen the lock nut, count the turns as you unscrew the old end, and fit the new end to the same number of turns. Torque the lock nut to the maker spec, fit the castle nut and cotter pin on the outer end, and grease the fitting if the part has one.
Three habits save most installs. Count the turns so the alignment stays close enough to drive to the shop. Replace the cotter pin with a new one, never reuse the old one. And check the ball joints and control arm bushes while the front end is apart, because worn neighbours wear new ends faster.
For deeper help, our guide on how to wire a winch to a battery covers safe jacking and battery work in the same garage, and our guide to the best adjustable wrenches for home use covers the wrenches for the lock nuts. Our guide to the best adjustable wrenches online covers where to buy the wrenches for this job.
Safety essentials
Safety rules
- Support the car on jack stands, never on the jack alone, before working underneath.
- Wear safety glasses; rust and grease fall straight down when you work under the car.
- Never reuse a cotter pin. A new pin costs almost nothing and holds the nut on.
- Torque the lock nut and castle nut to the maker spec, not by feel.
- Get a wheel alignment immediately after fitting any tie rod end.
- Test the steering at low speed in a quiet area before driving normally.
Three accessories that make the job safer and easier:
Grease Monkey nitrile gloves. Tie rod work is greasy work. Nitrile gloves keep the grease off your hands and give you a better grip on the lock nuts.
Read our guide to the best winch recovery kit before you buy.
DEWALT safety goggle. Safety glasses protect your eyes from rust and grease when you work under the car. Wear them for the whole job, not just the drilling.
Energizer PRO headlamp. A headlamp lights the steering rack and tie rod threads from the angle you need, with both hands free for the wrench.
Troubleshooting
| Symptom | Likely cause | Fix |
|---|---|---|
| Steering still loose after fitting | The other side is worn too | Check the opposite end and the inner ends; replace the worn side as well |
| Clunk over bumps | Loose castle nut or worn ball joint | Check the nut torque and the cotter pin, then check the ball joints |
| Car pulls to one side | Alignment not done after fitting | Book a wheel alignment; do not drive far on a bad alignment |
| New end will not thread on | Wrong thread for your car | Stop and check the part number against your year, make and model |
| Grease fitting will not take grease | Fitting blocked or wrong angle | Clean the fitting, try a different coupler angle, and replace the fitting if it stays blocked |
| Tyres wear on the inside edge | Toe setting wrong after the swap | Get the alignment checked; inner edge wear points to a toe problem |
Who should NOT buy these
Owners who have not checked fitment. Tie rod ends are vehicle-specific, and a part that almost fits does not fit. Check year, make, model and side first, or use our guide to the MOOG tie rod ends review to confirm the application.
Anyone with a bent steering rack. New tie rod ends cannot fix a bent rack or a damaged steering knuckle. If the rack is bent, the ends will wear out again in months.
Drivers who skip the alignment. Every tie rod end change needs a wheel alignment. If you will not pay for one, do not start the job; the new ends and the front tyres will both wear unevenly.
Owners of cars with sealed steering racks. Some modern cars use steering racks where the inner ends are not sold separately. Check with the maker before ordering inner ends for these cars.
Final verdict
Best overall: the MOOG ES800223. Greasable, problem-solver design, and the strongest aftermarket record on GM trucks. Check Price
Best full kit: the Detroit Axle 6-piece Silverado kit. Both sides, inner and outer, in one box. Check Price
Best inner end: the MOOG EV800085. The MOOG pick for Camry steering work. Check Price
Best for sedans: the Detroit Axle Camry kit. The full front set for the most common sedan of its era. Check Price
FAQ
What is a tie rod end alternative for cars?
An aftermarket tie rod end that replaces the original part without the dealer price. MOOG and Detroit Axle both make direct replacements for common cars, and this guide compares four of them by fitment, design and warranty.
How do I know if my tie rod ends are worn?
Look for loose steering, a clunk over bumps, uneven front tyre wear, and a car that wanders on the road. A mechanic can check them by jacking the front up and rocking the wheel side to side while watching the joint. You will need pliers for the boots; our guide to the best hose clamp pliers heavy duty covers the ones that grip.
Do I need an alignment after replacing tie rod ends?
Yes, always. The new end will not sit in exactly the same place as the old one, and even a small difference wears tyres unevenly. Budget for the alignment as part of the job.
Should I replace one tie rod end or both?
Replace the worn one at minimum, and both sides if the car has high mileage. Wear is usually even, and a new end on one side with a worn end on the other leaves the steering loose.
Are MOOG tie rod ends good?
MOOG is one of the most widely used aftermarket chassis brands, and the ES800223 is a greasable problem-solver design for GM trucks. Owners praise the grease fitting and the tight fit. Confirm the part number matches your car first.
What is the difference between inner and outer tie rod ends?
Outer ends connect to the steering knuckle and wear first, because they move the most. Inner ends connect to the steering rack and last longer. Most jobs replace the outer ends; full refreshes replace both. A full refresh often needs a separator; our guide to the best ball joint separators or pliers covers the tools.
Can I drive with a bad tie rod end?
Not safely. A worn tie rod end can separate from the knuckle, and then you lose steering on that wheel. If the steering feels loose or you hear a clunk, get it checked before driving further.
How long do tie rod ends last?
It varies with roads and driving, but many last well past 100,000 miles on smooth roads. Rough roads, potholes and kerb hits shorten the life. Greasable ends last longer when they are greased at every oil change.
Do Detroit Axle tie rod kits fit my car?
Detroit Axle makes kits for specific year ranges, like the 1999-2006 Silverado and the 1992-1996 Camry in this guide. Check the kit listing against your exact year, make and model before ordering. For the clamps in the kit, see our guide to the best hose clamp pliers on Amazon.
Sources
Manufacturer and spec sources
- MOOG ES800223 listing: Amazon listing
- MOOG chassis parts: moogparts.com
- Detroit Axle 6-piece Silverado kit listing: Amazon listing
- Detroit Axle steering parts: detroitaxle.com
- MOOG EV800085 listing: Amazon listing
- ACDelco parts: acdelco.com
- Detroit Axle Camry kit listing: Amazon listing
- Mevotech MES800223 part page: mevotech.com
- Grease Monkey nitrile gloves listing: Amazon listing
- DEWALT safety goggle listing: Amazon listing
Owner sources
- MOOG ES800223 owner reports: Amazon listing reviews
- Detroit Axle Silverado kit owner reports: Amazon listing reviews
- MOOG EV800085 owner reports: Amazon listing reviews
- Detroit Axle Camry kit owner reports: Amazon listing reviews
By Leo, Founder, WinchInsider
Leo founded WinchInsider to cut through winch and automotive marketing with published specs and real owner reports. Every guide on the site is research-based: we read the manuals, compare the numbers, and link our sources so you can check them yourself. More about the site and our process on the About Us page.
Related guides
- MOOG tie rod ends review
- Mevotech tie rod ends review
- Adjustable wrenches reviews and best brands
- Best adjustable torque wrench
- Best winch for Jeep Wrangler