Best Bed Extenders By Height

Disclosure: As an Amazon Associate, I earn from qualifying purchases. This comes at no extra cost to you.

A truck bed is never long enough, and a bed extender that sits at the wrong height is worse than no extender at all. The lumber slopes down to the tailgate, the kayak tips on a flat bar, and the load slides because the crossbar sits below the bed rail.

The answer is height: a bed extender that adjusts to your bed height, so the load sits level from the cab to the tailgate. Measure from the ground to the top of the bed rail, then match the extender to that height, because a crossbar set level with the bed rail carries the load flat, while a crossbar set at cab height carries a kayak over the roof.

This guide compares five bed extenders by height, from a Yakima LongArm with three load heights to a Mockins 2-in-1 that stands 68 to 75.5 inches upright, so you can pick the extender that matches your bed height and your load.

The 30-second answer

Buy the Yakima LongArm Aluminum Hitch Mount Truck Bed Extender Rack, Black for most loads. Buy the Mockins 2-in-1 All-Weather 750 Lbs Capacity Truck Bed Extender for accessories included. Buy the PENSUN Truck Bed Extender, 2 in 1 Design Foldable Truck Bed Extension for heavy loads. Buy the MaxxHaul 70231 Hitch Mount Truck Bed Extender for a simple budget pick. Buy the Boonedox T-Bone Truck Bed Extender (Black) for kayaks.

How we researched this guide

We profiled five bed extenders by height, checked Amazon listing data for each one through the Creators API, and reviewed maker pages, roundups and owner reports in retailer reviews about height, width, capacity and install. Height is the deciding dimension here: the Yakima LongArm carries loads at bed height, bed rail height and cab height, the Mockins adjusts from 21 to 28 inches flat and 68 to 75.5 inches upright, the PENSUN adjusts from 18.13 to 27.17 inches, and the MaxxHaul adjusts from 4 to 10 inches. The Boonedox T-Bone is height-adjustable through pin holes, but no height range is published, so we say so instead of guessing. We note where the capacity figures conflict: the PENSUN lists 800 lb while some documentation mentions 500 lb, and Autoguide says MaxxHaul rates the 70231 at 300 lb while the listing details say 350 lb.

Our quick picks

Best Overall

Yakima LongArm Aluminum Hitch Mount Truck Bed Extender Rack, Black

Best for most loads: an aluminum hitch-mount crossbar that carries 300 lb, extends the bed up to 4 ft and weighs 12 lb.

Best Accessories Included

Mockins 2-in-1 All-Weather 750 Lbs Capacity Truck Bed Extender

Best for accessories: a 750 lb 2-in-1 crossbar that comes with a stabilizer, ratchet straps, a red flag and reflectors.

Best Heavy Capacity

PENSUN Truck Bed Extender, 2 in 1 Design Foldable Truck Bed Extension

Best for heavy loads: a foldable 2-in-1 crossbar rated for 800 lb on the listing, with an anti-rattle clamp and rubber strips.

Best Budget

MaxxHaul 70231 Hitch Mount Truck Bed Extender

Best for a simple budget pick: a 350 lb hitch-mount crossbar with quick-release pins, a red flag and reflective tape.

Best for Kayaks

Boonedox T-Bone Truck Bed Extender (Black)

Best for kayaks: a curved crossbar that carries 300 lb, adds up to 4 ft to the bed and takes Yakima and YakAttack accessories.

Quick comparison

ProductHeight rangeUseWarrantyCheck Price
Yakima LongArm Aluminum Hitch Mount Truck Bed Extender Rack, Black3 positions, 14.25-42.75 inMost loadsLimited lifetimeCheck Price
Mockins 2-in-1 All-Weather 750 Lbs Capacity Truck Bed Extender21-28 in flat, 68-75.5 in uprightAccessories included10-yearCheck Price
PENSUN Truck Bed Extender, 2 in 1 Design Foldable Truck Bed Extension18.13-27.17 inHeavy loads1-yearCheck Price
MaxxHaul 70231 Hitch Mount Truck Bed Extender4-10 inBudget pick90-dayCheck Price
Boonedox T-Bone Truck Bed Extender (Black)Adjustable, no range publishedKayaks and canoes12-monthCheck Price

How to choose a bed extender by height

Receiver size and hitch rating

Receiver size and hitch rating decide whether the extender fits and how much it can carry. Every pick in this guide fits a 2-inch receiver, so check your receiver size before you order, because a 1-1/4-inch receiver will not take them. The hitch rating governs the load, not the extender rating, so a crossbar that claims 800 lb is still limited by the receiver it sits in. Best Tow Ropes Under 100

Load capacity

Load capacity decides whether the extender carries your load, and the picks here run from 300 lb to 800 lb. The PENSUN lists 800 lb, the Mockins carries 750 lb, the MaxxHaul lists 350 lb and the Yakima and the Boonedox each carry 300 lb. Treat the figures with care, because the PENSUN documentation mentions 500 lb and roundups vary on the MaxxHaul, so check your hitch rating first. Battery Tender Junior vs NOCO Genius1

Height adjustment

Height adjustment decides whether the load sits level, and the picks here adjust in different ways. The Yakima has three set positions from bed height to cab height, the Mockins and the PENSUN slide to a height, and the Boonedox uses pin holes. Measure your bed height first, because the extender must match it, not the other way round. Warning Lights Reviews

Bed extension length

Bed extension length decides how much longer the bed becomes, and the picks here add up to 4 ft to the bed. The Yakima, the Mockins and the Boonedox each add up to 4 ft, while the PENSUN adds about 4 ft. Measure the load before you order, and flag it with a red flag and lights if it blocks the tail lights, because a load that sticks out must be visible. Best First Aid Kit Under 50

Kayak and boat use

Kayak and boat use decides the shape of the crossbar, and a curved bar cradles a boat while a flat bar carries lumber. The Boonedox T-Bone is curved for kayaks and canoes, with a Groove track that takes RAM, YakAttack and Scotty accessories. A flat crossbar needs side arms or a cradle to hold a boat, so pick the curve if you haul a kayak most weekends. ABS Scan Tools vs OBDII

Height and loading level

Height and loading level decide how the load rides, and the picks here cover three levels: bed height for lumber, bed rail height for ladders, and cab height for kayaks. The Yakima reaches cab height with its height extension, while the Mockins stands upright for tall loads. Pick the level first, then the extender. AGM Batteries Review for Cars

Bed extenders by height and budget

TierWhat you getExample pick
EntryA simple 350 lb hitch-mount crossbar with quick-release pins and a red flag.MaxxHaul 70231 Hitch Mount Truck Bed Extender
MidAn aluminum 300 lb crossbar that extends the bed up to 4 ft and weighs 12 lb.Yakima LongArm Aluminum Hitch Mount Truck Bed Extender Rack, Black
TopA 750 lb 2-in-1 crossbar with a stabilizer, ratchet straps, a red flag and reflectors.Mockins 2-in-1 All-Weather 750 Lbs Capacity Truck Bed Extender

Types of bed extenders by height compared

TypeHow it worksBest forWatch out for
Bed-height extendersA crossbar that sits level with the bed, for lumber and long cargo.Flat loads at bed levelToo low for roof loads
Bed-rail-height extendersA crossbar set at the top of the bed rail, for ladders and tall gear.Ladders and tall gearNeeds the height set right
Cab-height extendersA crossbar raised to cab height, for kayaks over the roof.Kayaks and canoesLower capacity at cab height
Upright and vertical extendersAn extender that stands upright, for tall loads that will not lie flat.Tall and upright loadsNeeds a tall load to be useful

Detailed reviews

Five bed extenders compared by height, from a Yakima LongArm with three load heights to a Mockins 2-in-1 that stands 68 to 75.5 inches upright, each checked against its listing and the roundups. Measure your bed height first, because the height decides whether the load sits level.

Best Overall: Yakima LongArm Aluminum Hitch Mount Truck Bed Extender Rack, Black

Best Overall

Why the Yakima LongArm is our pick

The Yakima LongArm is the overall pick because it is the lightest way to carry a long load: an aluminum crossbar that weighs 12 lb, carries 300 lb and extends the bed up to 4 ft. The 60-inch crossbar slides into a 2-inch receiver, locks in three positions and fastens with a 5/8-inch threaded hitch bolt, so it stays put on the highway. Integrated tie-down points keep the load secure, and the aluminum build will not rust.

Yakima LongArm key specs

  • Type: Hitch-mount truck bed extender
  • Receiver: 2 inch per listing
  • Crossbar: 60 inch per listing
  • Capacity: 300 lb per listing
  • Positions: 3 per listing, heights 14.25-42.75 in from the tongue
  • Extends bed: Up to 4 ft per listing
  • Weight: 12 lb per listing
  • Material: Aluminum per listing
  • Hitch bolt: 5/8 inch threaded per listing
  • Use: Lumber, kayaks, long cargo
  • Tie-down: Integrated tie-down points per the maker
  • Warranty: Limited lifetime per listing

Yakima LongArm: fits and best for

The Yakima LongArm fits a driver who hauls lumber, ladders or a kayak a few times a month and wants the lightest extender in this guide. It suits a truck with a 2-inch receiver, and it pairs with ratchet straps and a red flag. It is less suited to a driver who needs the highest capacity here, because the Mockins and the PENSUN carry more.

Yakima LongArm pros and watch-outs

  • Weighs 12 lb, the lightest here
  • Aluminum build will not rust
  • 60-inch crossbar fits wide loads
  • Three positions for the load
  • Integrated tie-down points
  • Limited lifetime warranty
  • 300 lb capacity, less than the heavy picks
  • No anti-rattle clamp in the listing
  • No reflective tape in the listing
  • Needs a flag for long loads

Yakima LongArm: what owners report

Owner reports in retailer reviews commonly note the LongArm is light enough to fit and remove alone, and the aluminum build holds up to weather.

Ford lists the LongArm as a hitch-mount bed extender with a 60-inch crossbar and three adjustable positions, in lightweight aluminum at 12 lb. Ford on the Yakima LongArm.

Yakima LongArm: who should not buy

Do not buy the Yakima LongArm if you need the highest capacity in this guide. The 300 lb rating is honest, but the Mockins carries 750 lb and the PENSUN lists 800 lb. Buy one of those instead, and keep the LongArm for drivers who want the lightest extender.

Yakima LongArm: pair it with

Pair it with ratchet straps and a red flag, so the load stays put and is visible from behind.

We may earn a commission at no cost to you.

Set the crossbar height before you load, because the three positions change how the load sits over the tailgate. AGM Batteries Cost

Best Accessories Included: Mockins 2-in-1 All-Weather 750 Lbs Capacity Truck Bed Extender

Best Accessories Included

Why the Mockins 2-in-1 is our pick

The Mockins 2-in-1 is the accessories pick because it comes with everything in the box: a stabilizer, ratchet straps, a red flag, reflectors and four clevis pins, so there is nothing extra to buy. It carries 750 lb, works flat for long loads and upright for tall loads, and adjusts from 26.7 to 48.5 inches wide. It adds up to 4 ft to the bed, and the 10-year warranty is the longest in this guide.

Mockins 2-in-1 key specs

  • Type: 2-in-1 truck bed extender
  • Receiver: 2 inch per listing
  • Capacity: 750 lb per listing
  • Width: 26.7 to 48.5 inch per listing
  • Horizontal height: 21 to 28 inch per listing
  • Vertical height: 68 to 75.5 inch per listing
  • Extends bed: Up to 4 ft per listing
  • Weight: Per listing
  • Includes: Stabilizer, ratchet straps, red flag, reflectors, 4 clevis pins per listing
  • Material: Steel per roundups
  • Warranty: 10-year per listing
  • Use: Lumber, ladders, kayaks

Mockins 2-in-1: fits and best for

The Mockins 2-in-1 fits a driver who wants the whole kit in one box and a crossbar that works flat or upright. It suits lumber, ladders and kayaks, and it pairs with a bed mat to stop cargo sliding. It is less suited to a driver who wants the lightest extender, because it is heavier than the Yakima.

Mockins 2-in-1 pros and watch-outs

  • 750 lb capacity, the second highest here
  • Stabilizer, straps, flag and reflectors included
  • Works flat or upright
  • Width adjusts from 26.7 to 48.5 inches
  • 10-year warranty, the longest here
  • Heavier than the Yakima at 12 lb
  • No published weight in the listing
  • Upright mode needs a tall load to be useful
  • Needs the stabilizer fitted to stop wobble

Mockins 2-in-1: what owners report

Owner reports in retailer reviews commonly note the Mockins kit arrives with everything needed, and the width adjusts to fit the load.

Truck Bed Guide lists the Mockins 2-in-1 among the best truck bed extenders for hauling long cargo, with a 750 lb capacity and a 26.7 to 48.5 inch width. Truck Bed Guide on truck bed extenders.

Mockins 2-in-1: who should not buy

Do not buy the Mockins 2-in-1 if you want the lightest extender in this guide. It is heavier than the Yakima LongArm at 12 lb. Buy the Yakima instead, and keep the Mockins for drivers who want the full kit and the higher capacity.

Mockins 2-in-1: pair it with

Pair it with a bed mat to stop cargo sliding, and fit the stabilizer before you load, so the crossbar does not wobble.

We may earn a commission at no cost to you.

Fit the stabilizer and the clevis pins before you drive, because the 2-in-1 design needs both to stay rigid. AGM Batteries vs Flooded

Best Heavy Capacity: PENSUN Truck Bed Extender, 2 in 1 Design Foldable Truck Bed Extension

Best Heavy Capacity

Why the PENSUN 2-in-1 is our pick

The PENSUN 2-in-1 is the heavy capacity pick because the listing rates it for 800 lb, the highest figure in this guide, and the foldable design stores flat when it is not in use. It works flat for long loads and upright for tall loads, extends the bed about 4 ft, and comes with an anti-rattle clamp, rubber strips and reflective tape. One honest warning: some documentation mentions 500 lb while the listing title claims 800 lb, so check your hitch rating first, because the hitch rating governs no matter what the extender claims.

PENSUN 2-in-1 key specs

  • Type: 2-in-1 truck bed extender
  • Receiver: 2 inch per listing
  • Capacity: 800 lb per listing title
  • Foldable: Yes per listing
  • Extends bed: About 4 ft per listing
  • Weight: 30.9 lb per listing
  • Size: 46.85 x 18.11 x 3.15 inch per listing
  • Clamp: Anti-rattle clamp per listing
  • Strips: Rubber strips per listing
  • Tape: Reflective tape per listing
  • Material: Alloy steel per roundups
  • Warranty: 1-year per the listing
  • Height: 18.13-27.17 in per listing

PENSUN 2-in-1: fits and best for

The PENSUN 2-in-1 fits a driver who needs the most capacity on paper and a crossbar that folds flat for storage. It suits lumber and long loads, and it pairs with ratchet straps and a red flag. It is less suited to a driver who wants a single published capacity figure, because some documentation mentions 500 lb while the listing title claims 800 lb.

PENSUN 2-in-1 pros and watch-outs

  • 800 lb rating on the listing, the highest here
  • Folds flat for storage
  • Anti-rattle clamp included
  • Rubber strips protect the load
  • Reflective tape included
  • Capacity figure conflicts: 800 lb on the listing, 500 lb in some documentation
  • 1-year warranty, shorter than the Yakima and Mockins
  • Weighs 30.9 lb, heavier than the Yakima
  • No stabilizer in the listing

PENSUN 2-in-1: what owners report

Owner reports in retailer reviews commonly note the PENSUN folds flat for storage, and the anti-rattle clamp keeps it steady on the road.

Of Zen and Computing lists the PENSUN among the best truck bed extenders, noting the 800 lb rating in the title and 500 lb in some documentation. Of Zen and Computing on truck bed extenders.

PENSUN 2-in-1: who should not buy

Do not buy the PENSUN 2-in-1 if you want a single published capacity figure. Some documentation mentions 500 lb while the listing title claims 800 lb, so the honest figure is unclear. Buy the Mockins instead if the conflict bothers you.

PENSUN 2-in-1: pair it with

Pair it with ratchet straps and a red flag, so the load stays put and is visible from behind.

We may earn a commission at no cost to you.

Check your hitch rating before you load, because the hitch rating governs no matter what the extender claims. AGM Batteries vs Lead-Acid

Best Budget: MaxxHaul 70231 Hitch Mount Truck Bed Extender

Best Budget

Why the MaxxHaul 70231 is our pick

The MaxxHaul 70231 is the budget pick because it does the simple job well: a hitch-mount crossbar that carries 350 lb per the listing, adjusts from 28.25 to 48.75 inches wide and from 4 to 10 inches high, and fits a 2-inch receiver. Four quick-release clevis pins hold it together, the side arms fold down for storage, and a red flag and reflective tape come in the box. One honest note: Autoguide says MaxxHaul rates it at 300 lb, while the listing details say 350 lb, so treat the rating as approximate.

MaxxHaul 70231 key specs

  • Type: Hitch-mount truck bed extender
  • Receiver: 2 inch per listing
  • Capacity: 350 lb per listing
  • Width: 28.25 to 48.75 inch per listing
  • Length: 53.5 inch from hitch point per listing
  • Height: 4 to 10 inch adjustable per listing
  • Weight: 32 lb per listing
  • Size: 37 x 19 x 3 inch per listing
  • Pins: 4 quick-release clevis pins per listing
  • Includes: Red flag and reflective tape per listing
  • Arms: Side arms fold down per listing
  • Warranty: 90-day per roundups

MaxxHaul 70231: fits and best for

The MaxxHaul 70231 fits a driver who wants a simple extender for the occasional long load and does not need the highest capacity. It suits lumber and ladders, and it pairs with ratchet straps and a red flag. It is less suited to a driver who wants a published warranty longer than 90 days, because the roundups list a 90-day warranty.

MaxxHaul 70231 pros and watch-outs

  • 350 lb capacity per the listing
  • Quick-release clevis pins for fast setup
  • Width adjusts from 28.25 to 48.75 inches
  • Red flag and reflective tape included
  • Side arms fold down for storage
  • Capacity figure varies: 300 lb per Autoguide, 350 lb per the listing details
  • 90-day warranty, the shortest here
  • Weighs 32 lb, the heaviest here
  • No anti-rattle clamp in the listing

MaxxHaul 70231: what owners report

Owner reports in retailer reviews commonly note the MaxxHaul sets up fast with the quick-release pins, and the width adjusts to fit the load.

Top5Best lists the MaxxHaul 70231 among the best truck bed extenders, for ladders, canoes, kayaks, long pipes and lumber, with a 37 x 19 x 3 inch size. Top5Best on truck bed extenders.

MaxxHaul 70231: who should not buy

Do not buy the MaxxHaul 70231 if you want the longest warranty in this guide. The roundups list a 90-day warranty, while the Mockins carries 10 years and the Yakima carries a limited lifetime warranty. Buy one of those instead.

MaxxHaul 70231: pair it with

Pair it with ratchet straps, so the load stays put on the crossbar.

We may earn a commission at no cost to you.

Check the width before you load, because the side arms must be set to match the load. 12V Car Heaters Reviews Best Models

Best for Kayaks: Boonedox T-Bone Truck Bed Extender (Black)

Best for Kayaks

Why the Boonedox T-Bone is our pick

The Boonedox T-Bone is the kayak pick because the curved design cradles a kayak or canoe, so the boat sits in the curve instead of sliding on a flat bar. It carries 300 lb, adds up to 4 ft to the bed and weighs 19 lb, and the Groove track takes RAM, YakAttack and Scotty accessories, so rod holders and mounts fit straight on. Side ears come in the box.

Boonedox T-Bone key specs

  • Type: Curved truck bed extender
  • Receiver: 2 inch per listing
  • Capacity: 300 lb per listing
  • Extends bed: Up to 4 ft per listing
  • Weight: 19 lb per listing
  • Material: Aluminum per roundups
  • Track: Groove track for RAM, YakAttack and Scotty accessories per listing
  • Includes: Side ears per listing
  • Use: Kayaks, canoes, lumber
  • Warranty: 12-month per the listing
  • Colour: Black per listing
  • Height: Adjustable via pin holes, no range published

Boonedox T-Bone: fits and best for

The Boonedox T-Bone fits a driver who hauls a kayak or canoe most weekends and wants the boat to sit in a curve, not slide on a flat bar. It suits kayaks, canoes and lumber, and it pairs with straps and a red flag. It is less suited to a driver who wants a flat surface for lumber, because the curve is made for boats.

Boonedox T-Bone pros and watch-outs

  • Curved design cradles a kayak or canoe
  • Groove track takes RAM, YakAttack and Scotty accessories
  • Weighs 19 lb, lighter than the 2-in-1 picks
  • Side ears included
  • Adds up to 4 ft to the bed
  • 300 lb capacity, less than the heavy picks
  • Curve is less useful for flat lumber
  • No anti-rattle clamp in the listing
  • 12-month warranty, shorter than the Yakima and Mockins

Boonedox T-Bone: what owners report

Owner reports in retailer reviews commonly note the T-Bone holds a kayak steady, and the curved design keeps the boat from sliding.

Top5Best lists the Boonedox Groovy T-Bone among the best truck bed extenders, for kayaks, canoes, ladders and lumber. Top5Best on truck bed extenders.

Boonedox T-Bone: who should not buy

Do not buy the Boonedox T-Bone if you mostly haul flat lumber. The curve is made for a kayak or canoe, and a flat crossbar carries lumber better. Buy the Yakima LongArm instead, and keep the T-Bone for drivers who haul a boat.

Boonedox T-Bone: pair it with

Pair it with kayak straps and a red flag, so the boat stays in the curve and is visible from behind.

We may earn a commission at no cost to you.

Set the curve under the boat before you strap it down, because the boat must sit in the curve, not on the edge. 12V Car Heaters vs AC

Spec comparison

SpecYakima LongArmMockins 2-in-1PENSUN 2-in-1MaxxHaul 70231Boonedox T-Bone
TypeHitch-mount crossbar2-in-1 extender2-in-1 extenderHitch-mount crossbarCurved extender
Receiver2 inch2 inch2 inch2 inch2 inch
Capacity300 lb750 lb800 lb (title)350 lb300 lb
Height3 positions, 14.25-42.75 in21-28 in flat, 68-75.5 in upright18.13-27.17 in4-10 inAdjustable, no range published
Width60 inch26.7-48.5 inchPer listing28.25-48.75 inchPer listing
Extends bedUp to 4 ftUp to 4 ftAbout 4 ftPer listingUp to 4 ft
Weight12 lbPer listing30.9 lb32 lb19 lb
IncludesTie-down pointsStabilizer, straps, flag, reflectorsAnti-rattle clamp, rubber stripsRed flag, reflective tapeSide ears
WarrantyLimited lifetime10-year1-year90-day12-month
Best forMost loadsAccessories includedHeavy loadsBudgetKayaks
Amazon listingVerifiedVerifiedVerifiedVerifiedVerified
Check PriceCheck PriceCheck PriceCheck PriceCheck PriceCheck Price

How to set a bed extender to your bed height

Measure your bed height first: stand a tape from the ground to the top of the bed rail, and write the number down, because the extender must match it. Slide the crossbar into the receiver, push it in until the pin holes line up, and set the height to match the bed rail, because a load that sits crooked slides. Fit the 5/8-inch hitch bolt or the clevis pins, and tighten the anti-rattle clamp if your extender has one. Load the lumber, ladder or kayak onto the crossbar, strap it down with ratchet straps, and check the crossbar is level before you drive. For a kayak, raise the crossbar to cab height before you load, because a boat that rests on the cab and the crossbar rides level, and a boat that rests on one point tips. Our guide to the best tow ropes under 100 covers the straps you will use, and our guide to the best tool storage covers the tape and socket set you will reach for.

Check the pins, the clamp and the height after the first trip, because they settle and loosen on the road. Check the load after the first few miles, and re-tighten the straps if they have slackened, because a load that shifts can slide off the crossbar. If you carry a kayak at cab height, check the height again with the boat loaded, because the weight can pull the crossbar down a notch. Add lights if the load blocks the tail lights, and keep the red flag on the end, because a load that sticks out must be seen from behind. Keep the instructions and the spare hardware, because a missing pin is hard to replace. A level load is a safe load, so take the time to set the height right before you drive. Our guide to the best tow ropes under 100 covers the straps, and our guide to the best adjustable hitch mounts alternative to hitch covers the other way to carry a long load.

Safety essentials

  • Check the hitch rating before you load, because the extender capacity is not the hitch capacity.
  • Flag the load and add lights if it blocks the tail lights.
  • Tighten the hitch bolt and the anti-rattle clamp before you drive.
  • Test the width and height with the load before a long trip.
  • Never exceed the receiver rating, because the hitch is the weak point.
  • Check the pins after the first trip, because they settle and loosen.

Keep a phone charged while you fit these parts, because the fitment guides and install videos live on it. The three chargers below cover a spare socket, a second device and fast charging.

Anker 320 24W Dual-USB Mini Car Charger, to keep a phone charged while you work. See our 12V Adapters Reviews for Cars guide.

LISEN 48W USB C Car Charger Adapter 2 Pack, so a phone and a second device stay charged. See our 12V Adapters Reviews Best guide.

UGREEN 130W USB C Car Charger with Cable, for fast charging on long days away from home. See our 12V Adapters for Beginners Guide.

Troubleshooting

Most problems in this guide trace to one of the causes below, and the fix is usually a check rather than a replacement. Best Car Buffer for Scratches

SymptomLikely causeFix
Extender wobbles in the receiverHitch bolt looseTighten the bolt and fit the anti-rattle clamp
Load slides on the crossbarNo straps or paddingStrap the load and add rubber strips
Tail lights blocked by the loadLoad hangs past the tailgateAdd lights and a red flag
Pins rattle looseClevis pins not seatedCheck the pins after the first trip
Kayak tips on a flat crossbarNo cradle or side armsUse a curved extender or side arms
Extender too short for the loadBed extension too shortMeasure the load before you order

Who should NOT buy these

Do not buy an extender without checking the receiver size. Every pick in this guide fits a 2-inch receiver, and a 1-1/4-inch receiver will not take them. Check the receiver size on your truck before you order, because a crossbar that does not fit the receiver is useless. Best Car Buffer for Home Use

Do not buy on the extender capacity alone. The hitch rating governs the load, not the extender rating, so a crossbar that claims 800 lb is still limited by the receiver it sits in. Check your hitch rating first, and treat the PENSUN 800 lb figure with care, because some documentation mentions 500 lb. 12V Adapters Reviews for Cars

Do not carry a load past the tailgate without a flag. A load that sticks out must be visible from behind, and a load that blocks the tail lights needs lights too. Fit a red flag and add lights before you drive. 12V Adapters Reviews Best

Do not buy a flat crossbar for a kayak. A flat bar carries lumber well, but a kayak slides on it, and a curved crossbar cradles the boat. Buy the Boonedox T-Bone for a kayak, and keep a flat crossbar for lumber. 12V Adapters for Beginners Guide

Final verdict

Best Overall: Yakima LongArm Check Price — The lightest crossbar for most loads.

Best Accessories Included: Mockins 2-in-1 Check Price — The full kit for long and tall loads.

Best Heavy Capacity: PENSUN 2-in-1 Check Price — The heaviest capacity on paper, with a warning.

Best Budget: MaxxHaul 70231 Check Price — The simple budget crossbar.

Best for Kayaks: Boonedox T-Bone Check Price — The curved crossbar for kayaks.

FAQ

What height should a bed extender be?

It should sit level with the top of your bed rail, so the load lies flat from the cab to the tailgate. Measure from the ground to the top of the bed rail, then set the extender to that height. For a kayak over the roof, set it at cab height instead, and for a tall load that will not lie flat, stand the extender upright.

How much weight can a bed extender carry?

It depends on the extender and the hitch, and the picks here run from 300 lb to 800 lb. The PENSUN lists 800 lb, the Mockins carries 750 lb, the MaxxHaul lists 350 lb and the Yakima and the Boonedox each carry 300 lb. Check your hitch rating first, because the hitch rating governs, and treat the PENSUN figure with care, because some documentation mentions 500 lb.

Will a bed extender fit my truck?

It will if your truck has a 2-inch receiver, because every pick in this guide fits a 2-inch receiver. Check the receiver size on your truck before you order, and check the hitch class, because a Class III or IV hitch carries more than a Class II hitch. A 1-1/4-inch receiver will not take these extenders, so measure before you buy.

How far can a bed extender extend the bed?

The picks in this guide add up to 4 ft to the bed, so a 5-foot bed becomes a 9-foot bed with the extender fitted. The Yakima, the Mockins and the Boonedox each add up to 4 ft, while the PENSUN adds about 4 ft. Measure the load before you order, and flag it with a red flag and lights if it blocks the tail lights.

What is the best bed extender for kayaks?

The Boonedox T-Bone is the best pick for kayaks in this guide, because the curved design cradles a kayak or canoe, so the boat sits in the curve instead of sliding on a flat bar. It carries 300 lb, adds up to 4 ft to the bed and weighs 19 lb, and the Groove track takes RAM, YakAttack and Scotty accessories, so rod holders fit straight on.

Do I need a red flag on a load that sticks out?

Yes, because a load that hangs past the tailgate must be visible from behind, and a red flag marks the end of the load for drivers behind you. Add lights if the load blocks the tail lights, because the lights must be visible too. Check the overhang rules in your state, because the allowed overhang varies by place.

What is the difference between a 2-in-1 extender and a simple bed extender?

A 2-in-1 extender works flat for long loads and upright for tall loads, while a simple bed extender works flat only. The Mockins and the PENSUN are 2-in-1 extenders, and they are heavier than a simple bed extender, the PENSUN at 30.9 lb against the Yakima at 12 lb. Pick a 2-in-1 if you haul tall loads, and a simple bed extender if you want the lightest pick.

Can I use a bed extender with a trailer?

No, because the bed extender sits in the receiver, and the receiver is occupied while the extender is fitted. To tow a trailer, remove the extender first, then hitch the trailer. A bed extender is for carrying a load on the truck, not for towing, so plan the trip around one or the other.

How do I stop a bed extender wobbling?

Tighten the hitch bolt first, then fit the anti-rattle clamp if your extender has one, because the bolt and the clamp together stop the wobble. The Mockins comes with a stabilizer that does the same job, and the PENSUN has an anti-rattle clamp. Check the pins after the first trip, because they settle and loosen on the road.

Sources

By Leo, Founder, WinchInsider

Leo researches winches and automotive accessories from maker documents, listing evidence and owner reports, and writes every guide so a first-time buyer can choose with confidence.

Related guides

Yakima LongArm Aluminum Hitch Mount Truck Bed Extender Rack, Black

Leave a Comment