The stereo install was finished, but the wires hung loose behind the dashboard. Every bump made them rattle, and one wire had already rubbed bare against a metal edge.
A wiring harness clip fixes that, because it anchors the loom to the car instead of letting it hang. The right clip holds for years, while a loose loom chafes, rattles and eventually shorts.
This guide compares four wiring harness clip packs, from a 160-piece push-mount set to a heat-rated engine-bay pack, so you can match mount, size and heat rating to your loom and your car.
The 30-second answer
Buy the Xislet 160pcs Push Mount Cable Zip Ties Check Price for most harness jobs. Buy the Funnymoom 200pcs Wire Loom Routing Clips, 15 Sizes Check Price for a workshop stock in fifteen sizes. Buy the EPFORGE 120pcs Push Mount Cable Zip Ties, Heat Resistant Check Price for hot engine bays. Buy the WZJST 150pcs Nylon Cable Tie Buckle Clips Check Price for buckle-style interior work.
How we researched this guide
We profiled four wiring harness clip packs, checked Amazon listing data for each one through the Creators API, and reviewed guides about push-mount ties, hole sizes, nylon grades and heat ratings. Where a listing does not publish a figure, we say so instead of guessing.
Our quick picks
Best Overall
Xislet 160pcs Push Mount Cable Zip Ties
Best for most harness jobs: 160 push-mount ties in heavy duty nylon, with a Christmas-tree head that locks into a panel hole without screws.
Best Value
Funnymoom 200pcs Wire Loom Routing Clips, 15 Sizes
Best for a workshop stock: 200 clips in 15 sizes with zip ties included, so the right size is in the box for almost any loom.
Best for Heat
EPFORGE 120pcs Push Mount Cable Zip Ties, Heat Resistant
Best for hot engine bays: 120 assorted push-mount ties rated from minus 40 to 130 degrees C, with stud, push-pin and screw mounts.
Best Buckle Style
WZJST 150pcs Nylon Cable Tie Buckle Clips
Best for a buckle-style clip: 150 nylon cable tie buckles that zip a loom tight and hold it, for interior and trim work.
Quick comparison
| Product | Mount | Use | Warranty | Check Price |
|---|---|---|---|---|
| Xislet 160pcs Push Mount Cable Zip Ties | Push-mount, 160pcs | Full harness jobs | Not published | Check Price |
| Funnymoom 200pcs Wire Loom Routing Clips, 15 Sizes | Push-mount, 200pcs, 15 sizes | Workshop stock | Not published | Check Price |
| EPFORGE 120pcs Push Mount Cable Zip Ties, Heat Resistant | Push-mount, 120pcs, heat rated | Hot engine bays | Not published | Check Price |
| WZJST 150pcs Nylon Cable Tie Buckle Clips | Buckle style, 150pcs | Interior and trim work | Not published | Check Price |
How to choose automotive wiring harness clips
Mount type: push, screw or adhesive
Mount type decides whether the clip can hold at all, and it is the first thing to check. A push-mount tie needs a pre-drilled round hole, a screw mount needs a stud or a tapped hole, and an adhesive clip needs a clean flat surface. The Xislet and Funnymoom ties are push-mount, while the EPFORGE pack offers push-pin, stud and screw mounts. Match the mount to the surface, because the wrong mount holds nothing. Best All-Season Tires Under 100
Hole size
Hole size decides whether a push-mount tie locks or falls out, and it is the most common mistake in clip buying. Too loose and the tie pulls out under vibration, too tight and the panel can crack. Common hole sizes run from about 4.8 mm for small ties to about 10 mm for large ones. Measure the hole, or pull one old clip and match it, before you order a pack. Best All-Season Tires Under 200
Heat rating
Heat rating decides whether the clip survives an engine bay, and standard nylon softens above about 85 degrees C. The EPFORGE pack is rated from minus 40 to 130 degrees C, which covers a hot bay, while the other packs here do not publish a rating. If your loom runs near an exhaust or a turbo, buy a rated pack, because an unrated tie will go soft and drop the loom. Best Garage Security Cameras Under 100
Bundle size
Bundle size decides which tie fits the loom, and a tie that is too small cannot close around the wires. The Funnymoom pack covers this with fifteen sizes, while the other packs are assorted without a published size list. Measure the loom diameter before you order, because a tie that cannot close is useless, and a tie that is far too large leaves a loose loop. Best Garage Storage
Single use or releasable
Every tie in this guide is single use, which means it must be cut off to remove it. That is normal for push-mount ties, and it is why bulk packs make sense: you will use several on one job and more on the next. If you need to move wires often, buy releasable ties separately, because cutting a single-use tie every time wastes money and time. Best Hard Tonneau Cover Under 500
OEM clip or universal tie
An OEM clip matches one car and one hole exactly, while a universal tie fits many cars well enough. The Auveco 50 wiring harness clips are the OEM-style choice, with a 9 mm by 37 mm head that fits a 6.3 mm hole on many GM vehicles. If your car needs that exact clip, buy it, because a universal tie cannot replace a factory clip that also holds a connector. Best Mud Flaps
Wiring harness clips by budget
| Tier | What you get | Example pick |
|---|---|---|
| Small pack | A 120-piece heat-rated pack for engine-bay work. | EPFORGE 120pcs |
| Mid-range pack | A 160-piece push-mount pack for most harness jobs. | Xislet 160pcs |
| Workshop pack | A 200-piece pack in fifteen sizes for several cars. | Funnymoom 200pcs |
Types of wiring harness clips compared
| Type | How it works | Best for | Watch out for |
|---|---|---|---|
| Push-mount tie | A zip tie with a barbed head that locks into a hole. | Chassis and firewall looms | Needs a pre-drilled hole |
| Buckle clip | A clip that zips around the bundle and holds it. | Interior and trim work | No panel anchor |
| Screw mount | A tie base fixed with a screw or a stud. | Engine bays and flat panels | Needs a stud or a tapped hole |
| OEM clip | A factory clip shaped for one car and one hole. | Exact factory replacement | Fits one make only |
Detailed reviews
Each clip pack below is checked against its listing and the guides. Read the mount type and the hole size before you buy, because those two decide whether the clip can hold your loom at all.
Best Overall: Xislet 160pcs Push Mount Cable Zip Ties
Best Overall
Why the Xislet 160pcs is our pick
The Xislet 160-piece pack is the overall pick because it is the most useful bulk buy for harness work. Each tie has a push-pin Christmas-tree head that pushes into a pre-drilled round hole, where angled barbs grip the inside of the hole and lock the tie without screws, adhesives or rivets. The ties are heavy duty nylon rated at 50 lb-plus per the listing, so they hold a real loom, not just a single wire. With 160 pieces in the pack, one order covers a full rewire, a stereo install and a few repairs afterwards. The Christmas-tree head suits the common hole sizes used in car panels, so one pack covers most anchor points on a car.
Xislet 160pcs key specs
- Type: Push-mount cable zip ties
- Count: 160 pieces
- Head: Push-pin Christmas tree
- Material: Heavy duty nylon
- Strength: 50 lb-plus per the listing
- Mount: Push into a panel hole
- Tools: None needed
- Use: Wiring harness routing
- Colours: Not published
- Sizes: Assorted per the listing
- Releasable: No, single use
- Listing: Verified
Xislet 160pcs: fits and best for
This pack fits a home mechanic or restorer who is routing a loom along a chassis, firewall or door panel. It suits engine bays, interiors and trailers, anywhere a panel hole is available. If you only need a few clips for one small job, a smaller pack costs less, and if your car needs a specific OEM clip, buy that clip instead.
Xislet 160pcs pros and watch-outs
- 160 pieces in one pack
- No screws or tools needed
- 50 lb-plus nylon per the listing
- Christmas-tree head locks tight
- Fits most panel holes
- Single use, not releasable
- Needs a pre-drilled hole
- Sizes are assorted, not chosen
- Heat rating not published
Xislet 160pcs: what owners report
Owner reports in retailer reviews commonly note the Xislet ties hold well once pushed in, and the 160-piece pack lasts through several jobs.
Owners also report the heads fit standard panel holes, though some note the assorted sizes mean not every tie suits every hole. Niuli Electric explains how push-mount ties lock into a panel hole.
Xislet 160pcs: who should not buy
Do not buy this pack if your panels have no holes to push into. These ties need a pre-drilled round hole, and they will not stick to a flat surface. Skip it too if you need a specific OEM clip, because a universal tie cannot replace a factory clip.
Xislet 160pcs: pair it with
Pair it with a step drill bit, so a hole can be drilled to the right size for the tie head without cracking the panel.
We may earn a commission at no cost to you.
Push each tie in by hand until the head clicks, then pull the tail tight and trim it flush. Best Performance Monitors Under 100
Best Value: Funnymoom 200pcs Wire Loom Routing Clips, 15 Sizes
Best Value
Why the Funnymoom 200pcs is our pick
The Funnymoom 200-piece pack is the value pick because it covers the size problem that trips up every other pack. Fifteen sizes are in the box, with cable zip ties included, so a thin sensor wire and a thick power loom can both be clipped from the same order. The clips are push-mount for car wiring, which means they press into a panel hole and hold the loom without extra hardware. For a workshop or a restorer who works on several cars, this is the pack that stops the mid-job trip to the parts store. Fifteen sizes in one box means a thin sensor wire and a thick power loom can both be clipped, and the 200-piece count covers several cars at once.
Funnymoom 200pcs key specs
- Type: Wire loom routing clips, push mount
- Count: 200 pieces
- Sizes: 15
- Extras: Cable zip ties included
- Mount: Push into a panel hole
- Material: Nylon per the listing
- Use: Car wiring looms
- Tools: None needed
- Colours: Not published
- Heat rating: Not published
- Releasable: No, single use
- Listing: Verified
Funnymoom 200pcs: fits and best for
This pack fits a workshop, a restorer or a fleet owner who clips looms on more than one vehicle. It suits any car where the loom runs along a panel with holes to push into. If you only need one size for one job, a single-size pack wastes less, and if you work in an engine bay, check the heat rating first.
Funnymoom 200pcs pros and watch-outs
- 200 pieces, 15 sizes
- Zip ties included
- One pack covers most looms
- No tools needed
- Low outlay for the count
- Heat rating not published
- Sizes are fixed, not chosen
- Single use, not releasable
- Nylon grade not published
Funnymoom 200pcs: what owners report
Owner reports in retailer reviews commonly note the 15 sizes mean the right clip is usually in the box, and the included zip ties finish the job.
Owners also report the clips hold well on interior panels, though some note the heat rating is not published, so engine-bay use needs care. Car Interior advises matching the clip base to the mounting hole.
Funnymoom 200pcs: who should not buy
Do not buy this pack for a hot engine bay without checking the heat rating, because it is not published. Skip it too if you need one exact size, because fifteen sizes means most of the pack will go unused.
Funnymoom 200pcs: pair it with
Pair it with a small parts box with dividers, so the fifteen sizes stay sorted instead of mixing into one pile.
We may earn a commission at no cost to you.
Sort the sizes before you start, so the right clip is in your hand when the loom is in place. Best Storage Bins
Best for Heat: EPFORGE 120pcs Push Mount Cable Zip Ties, Heat Resistant
Best for Heat
Why the EPFORGE 120pcs is our pick
The EPFORGE 120-piece pack is the heat pick because it is the only pack here that publishes a temperature rating. The ties are rated from minus 40 to 130 degrees C, which covers a hot engine bay where standard nylon softens above about 85 degrees C. The pack offers three mounts in one: an M5 stud mount, a push-pin mount and a screw mount, in assorted sizes, and the ties are self-locking and UV resistant. For a loom that runs near an exhaust manifold or a turbo, this is the pack to buy. The three mounts in one pack mean a stud, a push-pin hole or a screw point can all be used, and the UV resistance suits a loom that sees sunlight.
EPFORGE 120pcs key specs
- Type: Push-mount cable zip ties, assorted
- Count: 120 pieces
- Temperature: Minus 40 to 130 degrees C
- Mounts: M5 stud, push-pin, screw
- Material: Heavy duty nylon
- UV resistant: Yes
- Self-locking: Yes
- Use: Engine bay and interior wiring
- Colours: Black
- Sizes: Assorted
- Releasable: No, single use
- Listing: Verified
EPFORGE 120pcs: fits and best for
This pack fits a mechanic who routes looms in an engine bay, near an exhaust or a turbo, where heat kills standard ties. It suits any car with a hot bay and a mix of mounting points. If your loom stays inside the cabin, a cheaper pack does the same job, and if you need one mount type only, the assorted pack wastes pieces.
EPFORGE 120pcs pros and watch-outs
- Rated minus 40 to 130 degrees C
- Three mount types in one pack
- UV resistant
- Self-locking
- 120 pieces
- Sizes are assorted, not chosen
- Single use, not releasable
- Warranty not published
- Black only
EPFORGE 120pcs: what owners report
Owner reports in retailer reviews commonly note the EPFORGE ties hold up in engine bays where cheaper ties went soft, and the three mounts cover most jobs.
Owners also report the assorted sizes suit mixed work, though some note a single-size pack is better for one repeated job. Car Interior warns against standard nylon ties in high-heat zones.
EPFORGE 120pcs: who should not buy
Do not buy this pack if your loom never leaves the cabin. The heat rating costs more than a cabin job needs. Skip it too if you need one exact size, because the assorted sizes mean many pieces will not fit your hole.
EPFORGE 120pcs: pair it with
Pair it with a heat shield sleeve for the loom, so the wires themselves are protected as well as the clips.
We may earn a commission at no cost to you.
Test one tie in the hottest spot first, and check it after a long drive before you clip the whole loom. Best Tool Storage
Best Buckle Style: WZJST 150pcs Nylon Cable Tie Buckle Clips
Best Buckle Style
Why the WZJST 150pcs is our pick
The WZJST 150-piece pack is the buckle-style pick because its cable tie buckle holds a loom in a different way from a push-mount tie. The buckle zips the tie tight around the bundle and locks it, which suits interior trim and dashboard work where the loom runs along a surface rather than through a panel hole. The clips are nylon and universal for car use, and 150 pieces is enough for a full interior rewire. For a loom that needs a firm zip tie rather than a panel mount, this is the pack to buy. A buckle tie suits interior trim and dashboard work, where the loom runs along a surface, and 150 pieces cover a full interior rewire.
WZJST 150pcs key specs
- Type: Nylon cable tie buckle clips
- Count: 150 pieces
- Material: Nylon
- Style: Buckle, zipper type
- Mount: Surface and loom routing
- Use: Car interior and trim wiring
- Tools: None needed
- Colours: Not published
- Sizes: Not published
- Heat rating: Not published
- Releasable: No, single use
- Listing: Verified
WZJST 150pcs: fits and best for
This pack fits a driver or installer who is routing wires behind a dashboard, along a door panel or under a carpet, where a buckle clip holds the loom without a panel hole. It suits stereo installs and interior rewires. If your loom runs along a chassis with panel holes, buy a push-mount pack instead, because a buckle clip has nothing to lock into.
WZJST 150pcs pros and watch-outs
- 150 pieces in one pack
- Buckle zips the loom tight
- No panel hole needed
- Suits interior and trim work
- Low outlay
- No panel mount
- Heat rating not published
- Sizes not published
- Single use, not releasable
WZJST 150pcs: what owners report
Owner reports in retailer reviews commonly note the WZJST buckles hold a loom tight behind trim panels, and the 150-piece pack covers a full interior job.
Owners also report the clips suit stereo installs, though some note the sizes are not listed, so matching a thick loom needs care. Constructive IT explains how to match a fixing to the mounting surface.
WZJST 150pcs: who should not buy
Do not buy this pack for a chassis loom that needs a panel mount. A buckle clip has nothing to lock into on a bare panel. Skip it too if you need a published heat rating, because none is listed.
WZJST 150pcs: pair it with
Pair it with a trim removal tool set, so panels come off without breaking clips when the loom goes in.
We may earn a commission at no cost to you.
Zip the buckle snug but not crushing, so the wires are held without pinching the insulation. Best Tow Ropes Under 100
Spec comparison
| Spec | Xislet 160pcs | Funnymoom 200pcs | EPFORGE 120pcs | WZJST 150pcs |
|---|---|---|---|---|
| Clip type | Push-mount tie | Routing clip | Push-mount tie | Buckle clip |
| Count | 160 pieces | 200 pieces | 120 pieces | 150 pieces |
| Sizes | Assorted | 15 sizes | Assorted | Not published |
| Material | Heavy duty nylon | Nylon | Heavy duty nylon | Nylon |
| Mount | Push-pin | Push-mount | Stud, push-pin, screw | Buckle |
| Heat rating | Not published | Not published | Minus 40 to 130 C | Not published |
| Strength | 50 lb-plus | Not published | Not published | Not published |
| Extras | None | Zip ties included | UV resistant | None |
| Best for | Most harness jobs | Workshop stock | Hot engine bays | Interior trim |
| Listing | Verified | Verified | Verified | Verified |
| Check Price | Check Price | Check Price | Check Price | Check Price |
How to fit wiring harness clips
Plan the route first, then fit the clips. Lay the loom along its path, mark an anchor point every 150 to 300 mm, and drill each hole to the size the tie head needs. Push each tie in by hand until the head clicks, run the loom through the tie, pull it snug and trim the tail flush. Check the loom cannot touch hot or moving parts. Push Mount Cable Ties Guide
Work from one end of the loom to the other, and leave a little slack at each connector so the wires are not pulled tight. For an engine bay, use the heat-rated pack and keep the loom clear of the exhaust. For an interior, use the buckle clips behind trim panels, and refit the panels gently so no clip is crushed. Push the fir-tree head into a matched hole until the barbs click behind the panel, and check the tie cannot pull out before you bundle the wires. Match the hole to the tie head, because a loose hole lets the tie pull out under vibration and a tight hole can crack the panel. Cable Ties and Clips Guide
Safety essentials
- Never route a loom over a sharp edge
- Keep wires clear of hot exhaust parts
- Do not over-tighten a tie on a thin wire
- Trim tails flush so they cannot cut hands
- Check the loom after the first drive
- Stop and seek a professional if a wire is bare
A clipped loom is safe only when it stays clear of heat and sharp edges. These rules keep the fitting safe, and the quiet cabin is a separate reward.
Anker 320 24W Dual-USB Mini Car Charger, to keep a phone charged while you work.
LISEN 48W USB C Car Charger Adapter 2 Pack, so a phone and a second device stay charged.
UGREEN 130W USB C Car Charger with Cable, for fast charging on long days away from home.
Troubleshooting
If a clip pulls out, check the hole size before assuming the clip is faulty. ABS Scan Tools vs OBDII
| Symptom | Likely cause | Fix |
|---|---|---|
| Clip pulls out | Hole too large, or wrong head | Measure the hole and match the head |
| Tie will not close | Loom too thick for the tie | Use a larger tie or split the loom |
| Loom rattles | Clips too far apart | Add clips every 150 to 300 mm |
| Wire chafes | Loom touches a sharp edge | Reroute the loom and fit a grommet |
| Tie goes soft | Heat above the nylon rating | Use a heat-rated pack |
| Clip breaks on fitting | Hole too small, or old nylon | Drill the hole to size |
Who should NOT buy these
Do not buy push-mount ties for a flat surface. They need a pre-drilled round hole, and they will not stick to a flat panel. Use a screw mount or an adhesive clip instead. AGM Batteries Review for Cars
Do not use unrated nylon in a hot engine bay. Standard nylon softens above about 85 degrees C, and a soft tie drops the loom onto hot parts. Buy the heat-rated pack for the bay. AGM Batteries Cost
Do not over-tighten a tie on thin wires. A crushed wire breaks inside its insulation, and the fault shows up weeks later. Pull the tie snug, not crushing. AGM Batteries vs Flooded
Do not buy a universal tie when you need an OEM clip. A factory clip that holds a connector cannot be replaced by a universal tie. Match the old clip first. AGM Batteries vs Lead-Acid
Final verdict
Best Overall: Xislet 160pcs Check Price — The most useful bulk pack in this guide.
Best Value: Funnymoom 200pcs Check Price — The best-stocked pack in this guide.
Best for Heat: EPFORGE 120pcs Check Price — The heat-rated choice in this guide.
Best Buckle Style: WZJST 150pcs Check Price — The best buckle clip in this guide.
FAQ
What is a wiring harness clip?
A wiring harness clip is a small fastener that anchors a bundle of wires along a chassis, firewall or interior panel. Push-mount clips press into a pre-drilled hole and lock with barbs, while buckle clips zip around the bundle. Clips stop wires rattling, chafing and drifting into hot or moving parts. Clips also stop a loose loom rubbing through insulation and shorting.
Are push-mount zip ties better than normal zip ties?
Push-mount ties do a different job from normal zip ties. A normal tie only bundles wires together, while a push-mount tie also anchors the bundle to a panel through its head. If the loom must stay in one place, a push-mount tie is better. If the loom only needs bundling, a normal tie is enough. Push-mount heads also suit a firewall or chassis rail where a normal tie has nothing to hold.
What hole size do push-mount ties need?
It depends on the tie. Small ties need a hole of about 4.8 to 5 mm, mid-size ties need about 6 to 6.3 mm, and large ties need about 7.8 to 10 mm. Too loose and the tie pulls out, too tight and the panel can crack. Measure the hole or match one old clip before ordering. If the hole is worn or oversize, use the next size up or a screw-mount clip instead.
Can I use nylon clips in an engine bay?
Yes, if the nylon is rated for the heat. Standard nylon softens above about 85 degrees C, which is not enough near an exhaust or a turbo. The EPFORGE pack in this guide is rated to 130 degrees C. If a pack does not publish a rating, keep it out of the hot bay. Route the loom away from the exhaust and the turbo where you can, even with a rated tie.
How do I remove a push-mount clip?
Push-mount clips are single use, so they are cut off rather than removed. Cut the tie tail with flush cutters, then push the head out from behind the panel or pry it out gently. Do not yank the loom, because that can break the panel or pull the wires. Keep a few spares in the toolbox, because a cut clip cannot be reused.
Do I need an OEM clip or a universal tie?
Buy the OEM clip when the factory clip also holds a connector or fits a shaped hole that a universal tie cannot match. The Auveco 50 clips fit a 6.3 mm hole on many GM vehicles. For general loom routing, a universal push-mount tie is cheaper and works well. A universal tie is also easier to find in a parts store than a dealer-only clip.
How many clips do I need for a full rewire?
A full engine-bay and interior rewire can use 100 or more clips, which is why the packs in this guide hold 120 to 200 pieces. Count the anchor points along the loom route before you order, then add a few spares. One small pack is enough for a single repair. Buy the larger pack when the price gap is small, because spares are always useful.
Will clips stop wires rattling?
Yes, if the loom is anchored at regular intervals and the ties are snug. Space clips every 150 to 300 mm along the run, and keep the loom clear of sharp edges and hot parts. A loose loom rattles and chafes, while a clipped loom stays quiet and lasts longer. A clipped loom also lasts longer because it does not flex at the same spot every bump.
What is the difference between a fir-tree and an arrowhead clip?
Both are push-mount heads. A fir-tree head has several barbs stacked like a Christmas tree and grips a range of hole sizes, while an arrowhead head has two barbs and suits lighter work. The Xislet ties in this guide use a Christmas-tree head, which is the most common type in car wiring. An arrowhead head suits a lighter loom, while a fir-tree head suits a heavier bundle.
Sources
- Amazon listing, Xislet 160pcs
- Amazon listing, Funnymoom 200pcs
- Amazon listing, EPFORGE 120pcs
- Amazon listing, WZJST 150pcs
- How to choose car wire clips, Car Interior
- Wiring Harness Clips Guide, Car Interior
- Push Mount Cable Ties Guide, Niuli Electric
- Cable Ties Clips Pro Guide, Constructive IT
- Auveco 14547 Wire Loom Routing Clip, Auto Fasteners and Clips
- Best 9mm Clips, University of Guns
By Leo, Founder, WinchInsider
Leo researches winches and automotive accessories from maker documents, listing evidence and owner reports, and writes every guide so a first-time buyer can choose with confidence.
Related guides
- 12V Car Heaters Reviews Best Models
- 12V Car Heaters vs AC
- 12V Car Heaters vs Electric Heaters
- 12V Heater Review
- Best Car Buffer for Scratches
- Best Car Buffer for Home Use
Xislet 160pcs Push Mount Cable Zip Ties