The car pulled left on the motorway, and the front tyres wore on the inside edge while the outside looked new. The wheels had just been balanced, and the shake was gone, but the pull was still there.
Balancing fixed the shake, but it could not fix the angles. The wheels were balanced and still pointing the wrong way, and only an alignment check would show it.
This guide compares five alignment tools for work on jack stands, from toe plates that cost little to a kit that reads all three angles, so you can check the alignment with the same tool types a shop uses, after suspension work with the car already on stands.
The 30-second answer
Buy the Tenhulzen Automotive 2-Wheel Alignment Tool – All-in-one (Camber/Caster/Toe Plates) – Made in USA 3300 Check Price to check all three angles in one tool. Buy the QuickTrick Portable Wheel Alignment Kit (13-18″ Wheels), DIY 4 Wheel Alignment Kit, Automotive Check Price for a complete kit on all four wheels. Buy the Longacre Toe-In Plates 52-79501, Black Anodized Aluminum, 2 Pack Check Price for a quick toe check. Buy the Specialty Products Company Fastrax Camber/Caster Gauge – 91000 Check Price for camber and caster numbers. Buy the Trackace Laser Wheel Alignment Gauge (written alternative — see below) for a laser toe reading.
How we researched this guide
We profiled five alignment tools, checked Amazon listing data for each verified pick through the Creators API, and reviewed maker instructions and owner reports in retailer reviews about accuracy, wheel fit and setup on jack stands. Where a listing does not publish a figure, we say so instead of guessing.
Our quick picks
Best Overall
Tenhulzen Automotive 2-Wheel Alignment Tool – All-in-one (Camber/Caster/Toe Plates) – Made in USA 3300
Best for checking all three angles at home: a 2-wheel alignment tool with a camber gauge that reads to a tenth of a degree, rim-referenced toe plates and a built-in caster turn-plate function.
Best Complete Kit
QuickTrick Portable Wheel Alignment Kit (13-18″ Wheels), DIY 4 Wheel Alignment Kit, Automotive
Best for a full home alignment kit: frames, a digital gauge, tapes, bungees and pins for 13 to 18 inch wheels, with a lifetime parts warranty.
Best Toe Plates
Longacre Toe-In Plates 52-79501, Black Anodized Aluminum, 2 Pack
Best for a quick toe check: a pair of black anodized aluminium toe plates with magnets and two tape measures, 23.5 inches long.
Best Camber/Caster Gauge
Specialty Products Company Fastrax Camber/Caster Gauge – 91000
Best for camber and caster numbers: a gauge that reads camber over 4 degrees either way and caster from minus 4 to plus 12 degrees, for most 13 to 18 inch wheels.
Best Laser Toe Check
Trackace Laser Wheel Alignment Gauge
Best for a laser toe reading: a self-calibrating laser gauge that reads total toe to one minute of arc, for rims from 10 to 22 inches.
We could not verify a live Amazon listing for the Trackace laser wheel alignment gauge at the time of writing. The button below goes to the closest verified Amazon option in this guide, the QuickTrick 4th Gen alignment kit.
Closest verified Amazon option in this guide:
Quick comparison
| Product | Angles read | Use | Warranty | Check Price |
|---|---|---|---|---|
| Tenhulzen Automotive 2-Wheel Alignment Tool – All-in-one (Camber/Caster/Toe Plates) – Made in USA 3300 | Camber to 0.1 degrees, caster and toe | All three angles in one tool | Not published | Check Price |
| QuickTrick Portable Wheel Alignment Kit (13-18″ Wheels), DIY 4 Wheel Alignment Kit, Automotive | 13-18 inch wheels, full kit | Full kit for all four wheels | Lifetime parts warranty | Check Price |
| Longacre Toe-In Plates 52-79501, Black Anodized Aluminum, 2 Pack | 23.5 inch plates, magnets, 2 tapes | Quick toe check, no gauge to learn | Not published | Check Price |
| Specialty Products Company Fastrax Camber/Caster Gauge – 91000 | Camber over 4 degrees, caster -4 to +12 | Camber and caster numbers, no kit needed | 1 year | Check Price |
| Trackace Laser Wheel Alignment Gauge | Laser toe to 1 minute of arc | Laser toe reading, no tapes | Not published | We could not verify a live Amazon listing for the Trackace laser wheel alignment gauge at the time of writing. The button below goes to the closest verified Amazon option in this guide, the QuickTrick 4th Gen alignment kit. Check Price |
How to choose an alignment tool for jack stands
Toe, camber and caster, know the angles
Toe is whether the front of the wheels points in or out, camber is whether the top of the wheel leans in or out, and caster is the angle of the steering axis. Toe wears tyres fast when it is wrong, camber wears one edge, and caster affects how the steering centres. A tool that reads one angle is a toe check, while a tool that reads all three is a full alignment check. Best Tow Ropes Under 100
Accuracy you can trust
Accuracy decides whether the number is useful, and every pick here publishes one. The Tenhulzen reads camber to a tenth of a degree, the Trackace reads toe to one minute of arc, and the SPC lists its camber and caster ranges plainly. A tool with no published accuracy is a guess. Check the published number before you buy, and measure twice to see if it repeats. Battery Tender Junior vs NOCO Genius1
Balancing is not alignment
Wheel balancing and wheel alignment fix different problems, and this guide is about alignment. Balancing spreads the weight evenly around the wheel so it does not shake, while alignment sets the angles so the car tracks straight and the tyres wear evenly. If the car vibrates at speed, balance the wheels. If it pulls or the tyres wear on one edge, check the alignment. Warning Lights Reviews
Wheel size and rim fit
Every alignment tool fits a range of wheel sizes, and the wrong range is a return. The QuickTrick and the SPC fit most 13 to 18 inch wheels, the Trackace fits rims from 10 to 22 inches, and the Longacre plates suit most cars and light trucks. Measure your wheel size before you order, and check the rim type, because some gauges need a clean hub face. Best First Aid Kit Under 50
Plates, gauges or lasers
Toe plates are the fastest check and the cheapest, a gauge on the wheel gives camber and caster numbers, and a laser gives a toe reading without tapes. Plates suit a quick check after suspension work, gauges suit a camber check after a lowering kit, and lasers suit anyone who wants a published accuracy number. Pick the tool type that matches the angle you need to check. ABS Scan Tools vs OBDII
One axle or four wheels
Some tools check one axle at a time and some check all four wheels at once. The Tenhulzen is a 2-wheel tool, so it works one axle at a time, while the QuickTrick frames all four wheels. A one-axle tool is fine for a front-end check, while a four-wheel kit suits a full alignment. Know which one you are buying before you order, because the setup time is very different. AGM Batteries Review for Cars
Alignment tools by budget
| Tier | What you get | Example pick |
|---|---|---|
| Toe plates | A pair of plates and tapes for a quick toe check after suspension work. | Longacre 79501 |
| Camber and caster gauge | A gauge that reads camber and caster numbers on one wheel. | SPC FasTrax 91000 |
| Laser toe check | A laser gauge that reads total toe to one minute of arc. | Trackace |
| Complete kit | Frames, a digital gauge and tapes for all four wheels. | QuickTrick 4th Gen |
Types of alignment tools compared
| Type | How it works | Best for | Watch out for |
|---|---|---|---|
| Toe plates | Two plates rest against the tyres and tapes read toe directly. | Quick toe checks | Toe only, no camber or caster |
| Camber and caster gauge | A gauge mounts on the wheel hub and reads camber and caster. | Camber checks after suspension work | No toe without an extra kit |
| Full alignment kit | Frames on all four wheels with a gauge and tapes. | Full home alignment | Costs more and takes longer to set up |
| Laser toe gauge | A laser reads total toe to a published accuracy. | Toe checks without tapes | Toe only, needs a clear line of sight |
| Static bubble balancer | A bubble level shows whether the wheel is balanced. | Balancing wheels at home | Checks balance, not alignment angles |
Detailed reviews
Each tool below is checked against its listing and the maker documents. Read the wheel size and the angles it reads before you buy, because those two decide whether the tool fits your car and your job.
Best Overall: Tenhulzen Automotive 2-Wheel Alignment Tool – All-in-one (Camber/Caster/Toe Plates) – Made in USA 3300
Best Overall
Why the Tenhulzen 3300 Alignment Tool is our pick
The Tenhulzen 3300 is the overall pick because it is the only tool in this guide that reads camber, caster and toe in one box, with a camber gauge that reads to a tenth of a degree. The listing describes a 2-wheel alignment tool with one plate carrying a camber gauge, one standard plate, two tape measures and a digital readout, all made in the USA. The toe reading is rim-referenced through stand-offs, so the tyre sidewall does not throw the number off, and the built-in turn-plate function checks caster without a separate plate.
Tenhulzen 3300 Alignment Tool key specs
- Type: 2-wheel alignment tool, camber, caster and toe
- Model: 3300
- Camber accuracy: To a tenth of a degree
- Toe: Rim-referenced via stand-offs
- Caster: Built-in turn-plate function
- Kit: 1 plate with camber gauge, 1 standard plate, 2 tapes, digital readout
- Use: One axle at a time
- Made in: USA
- Power: Digital readout, battery
- Warranty: Not published
- Fits: Most cars and light trucks
- Use: Home alignment checks
Tenhulzen 3300 Alignment Tool: fits and best for
The Tenhulzen 3300 fits home mechanics who want to check camber, caster and toe on one axle without booking a shop visit. It suits anyone who swaps wheels for balancing and wants the alignment checked while the car is already in the air. Work on a level floor and check that your wheels clear the stand-offs before you order.
Tenhulzen 3300 Alignment Tool pros and watch-outs
- Reads camber, caster and toe in one tool
- Camber gauge reads to a tenth of a degree
- Rim-referenced toe, not tyre sidewall
- Made in the USA
- Built-in caster turn-plate function
- One axle at a time, not four wheels
- Needs a level floor for good readings
- No published warranty
- Takes practice to read consistently
Tenhulzen 3300 Alignment Tool: what owners report
Owner reports in forum threads commonly note the Tenhulzen 3300 reads camber to a tenth of a degree, and the rim stand-offs are the feature owners mention for repeatable toe readings.
Owners also report the caster function works on a level floor, though a few note the plates take a run to learn, so expect a practice session first.
Tenhulzen 3300 Alignment Tool: who should not buy
Do not buy the Tenhulzen 3300 if you need a four-wheel alignment in one pass, because this is a 2-wheel tool that works one axle at a time. Skip it too if your floor is not level, because the readings depend on it.
Tenhulzen 3300 Alignment Tool: pair it with
Pair it with a set of jack stands and a level floor, so the car sits safely while you measure.
We may earn a commission at no cost to you.
Measure toe twice, once each way, and average the readings. AGM Batteries Cost
Best Complete Kit: QuickTrick Portable Wheel Alignment Kit (13-18″ Wheels), DIY 4 Wheel Alignment Kit, Automotive
Best Complete Kit
Why the QuickTrick 4th Gen Alignment Kit is our pick
The QuickTrick 4th Gen is the complete-kit pick because it is the only kit in this guide that brings frames, a digital gauge, tapes, bungees and pins in one case, so you can check toe, camber and caster on all four wheels without buying anything else. The listing describes a portable kit for 13 to 18 inch wheels, with a digital gauge and a lifetime parts warranty, made in the USA. For a home garage that aligns more than one car, this is the kit to buy.
QuickTrick 4th Gen Alignment Kit key specs
- Type: Portable 4-wheel alignment kit
- Generation: 4th Gen
- Wheels: 13 to 18 inch
- Tyres: Up to 30 inch
- Kit: Frames, digital gauge, tapes, bungees, pins
- Gauge: Digital camber and caster
- Toe: Tape measures on the frames
- Made in: USA
- Warranty: Lifetime parts warranty
- Award: SEMA Global Media Award per maker
- Use: All four wheels
- Power: Digital gauge, battery
QuickTrick 4th Gen Alignment Kit: fits and best for
The QuickTrick 4th Gen fits home mechanics who align more than one car and want a complete kit in one case. It suits anyone who wants frames on all four wheels at once, so the front and rear can be compared without moving plates. Check that your wheels are 13 to 18 inches before you order.
QuickTrick 4th Gen Alignment Kit pros and watch-outs
- Complete kit, nothing else to buy
- Frames on all four wheels at once
- Digital gauge for camber and caster
- Lifetime parts warranty
- Made in the USA
- Costs more than toe plates alone
- Frames take time to fit on all four wheels
- 13 to 18 inch wheels only in this listing
- Needs a level floor for good readings
QuickTrick 4th Gen Alignment Kit: what owners report
Owner reports in retailer reviews commonly note the QuickTrick 4th Gen fits all four wheels at once, and the digital gauge is the feature owners mention for clear camber and caster readings.
Owners also report the kit travels well in its case, though a few note fitting four frames takes time, so allow an hour for the first setup.
QuickTrick 4th Gen Alignment Kit: who should not buy
Do not buy the QuickTrick 4th Gen if you only need a quick toe check, because toe plates cost far less and set up faster. Skip it too if your wheels are outside 13 to 18 inches, because the frames in this listing will not fit.
QuickTrick 4th Gen Alignment Kit: pair it with
Pair it with a level floor and a tape measure you trust, so the toe readings repeat.
We may earn a commission at no cost to you.
Fit all four frames before you read anything. 12V Car Heaters Reviews Best Models
Best Toe Plates: Longacre Toe-In Plates 52-79501, Black Anodized Aluminum, 2 Pack
Best Toe Plates
Why the Longacre 79501 Toe Plates is our pick
The Longacre 79501 is the toe-plate pick because it is the simplest tool in this guide and the fastest to set up, and its numbers are published plainly. The listing describes a pair of black anodized aluminium toe-in plates, 23.5 inches long, with magnets and two tape measures in the box. The plates rest against the tyres and the tapes read toe directly, front and rear, with no gauge to learn. Maker instructions say to set caster and camber first, because toe is the last angle to set. For a quick check after suspension work, before a shop visit, this is the tool to buy.
Longacre 79501 Toe Plates key specs
- Type: Toe-in plates, pair
- Model: 52-79501
- Material: Black anodized aluminum
- Length: 23.5 inches
- Kit: 2 plates, 2 tape measures
- Magnets: Yes, hold plates to the wheels
- Measures: Toe only
- Use: Quick toe check
- Power: None, manual
- Warranty: Not published
- Fits: Most cars and light trucks
- Instructions: Maker PDF per roundups
Longacre 79501 Toe Plates: fits and best for
The Longacre 79501 fits anyone who needs a quick toe check after suspension work or a tyre change. It suits a home mechanic who wants a number before deciding whether a shop alignment is needed, and the magnets suit anyone working alone, because the plates stay put while you read the tapes. Check that your tyres are even and your floor is level before you measure.
Longacre 79501 Toe Plates pros and watch-outs
- Fastest setup in this guide
- No gauge to learn, tapes read toe directly
- Magnets hold the plates while you work
- Black anodized aluminium lasts
- Lowest outlay of any pick here
- Toe only, no camber or caster
- Tyre runout affects the reading
- Needs a level floor
- No published warranty
Longacre 79501 Toe Plates: what owners report
Owner reports in forum threads commonly note the Longacre plates are the fastest way to check toe, and the magnets are the feature owners mention for working alone.
Owners also report the plates repeat well on a level floor, though a few note tyre runout can move the reading, so measure twice and average.
Longacre 79501 Toe Plates: who should not buy
Do not buy the Longacre 79501 if you need camber or caster numbers, because these plates read toe only. The Tenhulzen 3300 or the SPC gauge are the picks for camber and caster. Skip it too if your tyres have uneven runout, because the reading will move.
Longacre 79501 Toe Plates: pair it with
Pair it with a level floor and a second tape measure, so you can cross-check the reading.
We may earn a commission at no cost to you.
Set camber and caster first, then read toe. 12V Car Heaters vs AC
Best Camber/Caster Gauge: Specialty Products Company Fastrax Camber/Caster Gauge – 91000
Best Camber/Caster Gauge
Why the SPC FasTrax 91000 Gauge is our pick
The SPC FasTrax 91000 is the camber and caster pick because it is a dedicated gauge with published ranges, and it mounts on the wheel in seconds. The listing describes a gauge that reads camber over 4 degrees either way and caster from minus 4 to plus 12 degrees, for most 13 to 18 inch wheels, with a 1-year warranty. Maker documents note an optional toe kit, part 91100, for buyers who also want toe. For a home garage that needs camber and caster numbers without a full kit, this is the gauge to buy.
SPC FasTrax 91000 Gauge key specs
- Type: Camber and caster gauge
- Model: 91000
- Camber range: Over 4 degrees either way
- Caster range: Minus 4 to plus 12 degrees
- Wheels: Most 13 to 18 inch
- Mounting: Magnetic, on the wheel hub
- Optional toe kit: Part 91100
- Larger sibling: 91010 for 17 to 22 inch wheels
- Power: None, manual
- Warranty: 1 year
- Use: Camber and caster checks
- Made for: Home and shop use
SPC FasTrax 91000 Gauge: fits and best for
The SPC FasTrax 91000 fits home mechanics who need camber and caster numbers after suspension work or a lowering kit. It suits anyone who wants a gauge that mounts on the wheel hub in seconds. Check that your wheels are 13 to 18 inches and the hub face is clean before you measure.
SPC FasTrax 91000 Gauge pros and watch-outs
- Published camber and caster ranges
- Mounts on the wheel hub in seconds
- Optional toe kit for buyers who want toe too
- 1-year warranty
- No batteries and no power needed
- Camber and caster only, no toe without the kit
- 13 to 18 inch wheels only in this listing
- Needs a clean hub face
- No digital readout
SPC FasTrax 91000 Gauge: what owners report
Owner reports in retailer reviews commonly note the SPC 91000 mounts on the hub in seconds, and the camber scale is the feature owners mention for easy reading.
Owners also report the gauge repeats well between checks, though a few note a dirty hub face throws the reading off, so clean the hub first. SPC maker site, spcalignment.com.
SPC FasTrax 91000 Gauge: who should not buy
Do not buy the SPC FasTrax 91000 if you need toe readings too, because this gauge reads camber and caster only unless you add the optional 91100 toe kit. Skip it too if your wheels are outside 13 to 18 inches, because this listing will not fit.
SPC FasTrax 91000 Gauge: pair it with
Pair it with the optional 91100 toe kit if you want toe as well, so one gauge covers more angles.
We may earn a commission at no cost to you.
Clean the hub face before you mount the gauge. 12V Car Heaters vs Electric Heaters
Best Laser Toe Check: Trackace Laser Wheel Alignment Gauge
Best Laser Toe Check
Why the Trackace Laser Alignment Gauge is our pick
The Trackace is the laser pick because it is the only tool in this guide that reads toe with a laser, and its accuracy is published plainly. Maker documents describe a self-calibrating laser gauge that reads total toe to one minute of arc, which is 0.0166 degrees, for rims from 10 to 22 inches, with a Class 2 laser at 650nm and two AAA batteries. It is listed here as a written alternative because we could not verify a live Amazon listing for the Trackace, so the button below goes to the closest verified option, the QuickTrick 4th Gen kit.
Trackace Laser Alignment Gauge key specs
- Type: Laser wheel alignment gauge
- Laser: Class 2, 650nm, under 1mW
- Accuracy: One minute of arc, 0.0166 degrees
- Rims: 10 to 22 inches
- Calibration: Self-calibrating
- Power: 2 AAA batteries, not supplied
- Maker: Trackace, UK
- Patent: GB2477147 per maker
- Clearance: From 100mm
- Use: Total toe checks
- Warranty: Not published
- Mounting: On the wheel rim
Trackace Laser Alignment Gauge: fits and best for
The Trackace fits anyone who wants a laser toe reading rather than tape measures. It suits a home mechanic who values a published accuracy number, because one minute of arc is a real figure to judge by. Check the maker store for the current model before you order, because sizes and stock change.
Trackace Laser Alignment Gauge pros and watch-outs
- Laser reading, no tapes to read
- Published accuracy to one minute of arc
- Fits rims from 10 to 22 inches
- Self-calibrating
- UK maker with a published patent
- No verified Amazon listing found
- Needs 2 AAA batteries, not supplied
- Toe only, no camber or caster
- Laser needs a clear line of sight
Trackace Laser Alignment Gauge: what owners report
Owner reports in roundups commonly note the Trackace reads toe with a laser, and the self-calibration is the feature owners mention for quick setup.
Owners also report the laser dot is easy to read, though a few note the rim range must be checked first.Manualzilla hosts the Trackace manual.
Trackace Laser Alignment Gauge: who should not buy
Do not buy the Trackace through Amazon if you need a one-click verified purchase, because we could not verify a live listing for it. Buy the QuickTrick 4th Gen kit, or check the maker store for the Trackace. Skip it too if you need camber or caster, because this gauge reads toe only.
Trackace Laser Alignment Gauge: pair it with
Pair it with a level floor and two AAA batteries.
We could not verify a live Amazon listing for the Trackace laser wheel alignment gauge at the time of writing. The button below goes to the closest verified Amazon option in this guide, the QuickTrick 4th Gen alignment kit.
We may earn a commission at no cost to you.
Never look into the laser beam. 12V Heater Review
Spec comparison
| Spec | Tenhulzen 3300 Alignment Tool | QuickTrick 4th Gen Alignment Kit | Longacre 79501 Toe Plates | SPC FasTrax 91000 Gauge | Trackace Laser Alignment Gauge |
|---|---|---|---|---|---|
| Angles read | Camber, caster, toe | Toe, camber, caster | Toe only | Camber, caster | Toe only |
| Camber accuracy | To a tenth of a degree | Digital gauge | Not read | Over 4 degrees either way | Not read |
| Toe reading | Rim-referenced tapes | Tape measures on frames | Tape measures | Optional 91100 kit | Laser, 1 minute of arc |
| Wheels fit | Most cars and light trucks | 13 to 18 inch | Most cars and light trucks | Most 13 to 18 inch | Rims 10 to 22 inch |
| Axles at once | One axle | Four wheels | One axle | One wheel | One wheel |
| Power | Digital readout, battery | Digital gauge, battery | None, manual | None, manual | 2 AAA batteries |
| Kit contents | 2 plates, 2 tapes, readout | Frames, gauge, tapes, pins | 2 plates, 2 tapes | Gauge only | Laser gauge |
| Made in | USA | USA | Not published | Not published | UK |
| Use | Home alignment checks | Full home alignment | Quick toe check | Camber and caster checks | Total toe checks |
| Warranty | Not published | Lifetime parts warranty | Not published | 1 year | Not published |
| Check Price | Check Price | Check Price | Check Price | Check Price | We could not verify a live Amazon listing for the Trackace laser wheel alignment gauge at the time of writing. The button below goes to the closest verified Amazon option in this guide, the QuickTrick 4th Gen alignment kit. Check Price |
How to use an alignment tool
Work on a level floor, chock the wheels you are not measuring, and set the car on jack stands before you fit any tool. Fit the plates or gauge on one axle, take the toe or camber reading, and write it down before you change anything. Adjust a tie rod a little at a time, re-measure after each change, and roll the car forward and back so the suspension settles. The maker instructions for the Longacre plates walk through the full toe check step by step. Longacre toe plate instructions
Check camber with the gauge on the hub, then caster with the turn-plate function if your tool has one, and compare both sides before you decide anything is wrong. A reading that differs side to side points to a bent part or a worn bush, not to a bad tool. The Tenhulzen assembly instructions show how the plates, the gauge and the tapes fit together. Tenhulzen 3300 assembly instructions
After the alignment reads true, check the tyres for uneven wear, because alignment shows up first in the tread: our Best All-Season Tires Under 100 guide covers the tyres that reward a straight car. For the tie-rod and lock-nut adjustments themselves, our Best Adjustable Wrenches Home Use guide covers the wrenches that fit the job.
Safety essentials
- Chock the wheels and use jack stands, never a jack alone
- Work on a level floor, or the readings will lie
- Never look into a laser beam
- Keep fingers clear of the wheels and the steering
- Check the car is stable before you measure
- Stop and seek a professional if parts look bent
An alignment check puts you under and around a car on stands, and a laser gauge adds a beam to watch. These rules keep the job safe, and the numbers are a separate reward.
Anker 320 24W Dual-USB Mini Car Charger, to keep a phone charged while you work.
LISEN 48W USB C Car Charger Adapter 2 Pack, so a phone and a second device stay charged.
UGREEN 130W USB C Car Charger with Cable, for fast charging on long days away from home.
Troubleshooting
If the readings do not repeat, check the floor and the tool before changing anything. 12V Adapters Reviews for Cars
| Symptom | Likely cause | Fix |
|---|---|---|
| Toe readings differ left and right | Tyre runout, or the car has not settled | Roll the car and re-measure, then average the readings |
| Camber gauge will not zero | Dirty hub face, or the gauge is not seated | Clean the hub face and remount the gauge |
| Plates slide on the floor | Floor is not level, or the tyres are wet | Move to a level dry floor and chock the wheels |
| Laser dot jumps around | Rim is dirty, or the gauge is loose | Clean the rim and remount the gauge firmly |
| Readings change after rolling the car | Suspension has not settled | Roll forward and back, then re-measure |
| Tape measures disagree | Tapes are not level, or read at different points | Read both tapes at the same height and re-check |
Who should NOT buy these
Do not buy an alignment tool if your car has been in a crash. Bent parts need a shop, and no home tool can straighten bent metal. Check the car first, then buy the tool. 12V Adapters Reviews Best
Do not buy toe plates if you need camber numbers. Plates read toe only, and camber needs a gauge. Buy the gauge or the kit instead. 12V Adapters for Beginners Guide
Do not measure on a slope. Alignment readings depend on a level floor, and a slope lies to every tool. Find a flat bay first. 12V Adapters Review Amazon
Do not trust a single reading. Measure twice, roll the car, and measure again, because one reading can be a fluke. A reading that repeats is a real number. 12V Adapters Alternative for LED Lights
Final verdict
Best Overall: Tenhulzen 3300 Alignment Tool Check Price — All three angles in one tool, built in the USA.
Best Complete Kit: QuickTrick 4th Gen Alignment Kit Check Price — The complete kit, frames and digital gauge included.
Best Toe Plates: Longacre 79501 Toe Plates Check Price — The fastest toe check, at the lowest outlay.
Best Camber/Caster Gauge: SPC FasTrax 91000 Gauge Check Price — Camber and caster numbers in seconds, on the hub.
Best Laser Toe Check: Trackace Laser Alignment Gauge We could not verify a live Amazon listing for the Trackace laser wheel alignment gauge at the time of writing. The button below goes to the closest verified Amazon option in this guide, the QuickTrick 4th Gen alignment kit. Check Price — The laser toe check, accurate to a minute of arc.
FAQ
Can I align my car at home?
Yes, you can check and adjust toe, camber and caster at home with the tools in this guide, provided you work on a level floor and follow the maker instructions. A home check suits a car that pulls slightly or wears tyres unevenly. A car that has been in a crash or has bent parts needs a shop, because no home tool can straighten bent metal.
What is the difference between wheel balancing and wheel alignment?
Balancing spreads the weight evenly around the wheel so it does not shake at speed, while alignment sets the wheel angles so the car tracks straight and the tyres wear evenly. A vibration at speed points to balancing, while a pull to one side or wear on one tyre edge points to alignment. The tools in this guide check alignment angles, not balance.
What alignment tools do professional shops use?
Professional shops use laser or camera 4-wheel alignment rigs that read all four wheels at once, which is a different machine from the hand tools in this guide. Toe plates, camber and caster gauges and laser toe gauges cover home checks and quick toe readings after suspension work. Use the hand tools to check and adjust at home, and book a shop rig for a full four-wheel laser alignment.
How accurate is a home alignment tool?
Accurate enough to catch a real problem, if you work on a level floor and measure twice. The Tenhulzen reads camber to a tenth of a degree, the Trackace reads toe to one minute of arc, and the SPC lists its ranges plainly. A shop laser rig is more precise, but a home tool that repeats its own reading is good enough to decide whether a shop visit is needed.
What wheel sizes do these tools fit?
It depends on the tool. The QuickTrick and the SPC fit most 13 to 18 inch wheels, the Trackace fits rims from 10 to 22 inches, and the Longacre plates suit most cars and light trucks. Measure your wheel size and check the rim type before you order, because a gauge that will not mount on your wheel is a return.
Can I check caster at home?
Yes, with a tool that has a caster function. The Tenhulzen has a built-in turn-plate function for caster, and the QuickTrick and the SPC gauge read caster as well. Caster is checked by turning the wheel through a set angle and reading the change, so a level floor and a turn plate matter. Toe plates alone cannot check caster.
Why do my toe readings change after I roll the car?
Rolling the car settles the suspension and the tyres, so the reading moves. Always roll the car forward and back after an adjustment, then re-measure, because a reading taken before the car settles is not the real number. Tyre runout also moves the reading, so measure twice and average the two readings for a stable figure.
Is the Trackace available on Amazon?
We could not verify a live Amazon listing for the Trackace laser wheel alignment gauge at the time of writing. The button in its card goes to the closest verified Amazon option in this guide, the QuickTrick 4th Gen alignment kit. Check the maker store for the current Trackace model and stock before you order, because sizes and stock change.
Do I still need a shop alignment?
Yes, sometimes. A home check suits a car that pulls slightly or wears tyres unevenly, and it tells you whether a shop visit is needed. A car that has been in a crash, has bent parts, or needs a four-wheel laser alignment should go to a shop. Use the home tools to check, and the shop to fix what you cannot.
Sources
- Amazon listing, Tenhulzen 3300 alignment tool, ASIN B00PKI0YSU
- Amazon listing, QuickTrick 4th Gen alignment kit, ASIN B07WJTJBY7
- Amazon listing, Longacre 79501 toe plates, ASIN B000VAOHB2
- Amazon listing, SPC FasTrax 91000 gauge, ASIN B000PG6OW2
- Amazon listing, QuickTrick 4th Gen kit, closest verified option for the Trackace pick
- Tenhulzen 3300 assembly instructions, Summit Racing
- Tenhulzen maker store, wheelalignmenttools.com
- Longacre toe plate instructions, Longacre Racing
- Best wheel alignment tools, Motor Advises
- SPC maker site, alignment tools
By Leo, Founder, WinchInsider
Leo researches winches and automotive accessories from maker documents, listing evidence and owner reports, and writes every guide so a first-time buyer can choose with confidence.
Related guides
- 12V Adapters Alternative to USB
- Best ATV Winch
- Best Jump Starter
- Best Engine Oil
- Best Automotive Multimeters vs Watts
- Best Automotive Borescope for Mechanics
Tenhulzen Automotive 2-Wheel Alignment Tool – All-in-one (Camber/Caster/Toe Plates) – Made in USA 3300