Awnings Do It Yourself Guide

Disclosure: As an Amazon Associate, I earn from qualifying purchases. This comes at no extra cost to you.

You pull into camp late, the sun is still hard on the windscreen, and the only shade is the shadow of the car itself. An hour later the same sun has moved, the shadow has gone, and dinner is cooked in full glare.

A car camping awning fixes that by giving you a roof that travels with the car. It bolts to the roof rack, rolls out in minutes, and turns the side of the vehicle into a shaded room for cooking, eating and sitting out a shower.

This guide walks through the whole do-it-yourself job: choosing the size and type, mounting it on a roof rack, setting it up at camp, and keeping it alive through wind, rain and storage. No prior awning experience is assumed, and every step names the tool or check it needs.

The 30-second answer

Pick a pull-out awning as wide as your roof rack for a first setup, or a 270-degree awning if you want shade around the back as well. Mount it to the roof rack with the maker brackets, spaced as far apart as practical, torqued to the maker figures. Set it up with a downward pitch, guy ropes on every leg and pegs in the ground, and pack it away dry. Never leave any awning up in strong wind.

How we researched this guide

We checked maker fitting instructions from ARB and Overland Vehicle Systems, step-by-step installs of the ARB touring awning and the Rhino-Rack Batwing 270, the SunSetter owner manual, and measuring and sizing guides from 1800 Awnings, MyAwnings, Shelter Lane and NRTechStudio, plus owner install reports. Where a maker does not publish a figure, we say so instead of guessing.

What a car camping awning is

A car camping awning is a fabric shelter that lives on the side of a vehicle, usually bolted to a roof rack or roof bars, and rolls or folds out to make shade. The common pull-out type is a rectangle of fabric on a roller, with two legs that drop down and guy ropes that peg it to the ground. A 270-degree awning swings around the side and the back of the vehicle on hinged arms, so it shades the rear as well as the side, which suits a tailgate kitchen. A fixed awning, the kind on the side of a house, is a different product: it mounts to a wall, not a roof rack, and this guide covers vehicle awnings, with house-awning mounting principles noted only where they overlap.

The fabric is usually a coated polyester or canvas, and the frame is aluminium poles and arms. The whole unit packs into a bag or a hard case on the roof rack, so it travels with the car and is ready at every stop. That is the point of it: shade that is already there, with no separate tent to pitch and no poles to find in the dark.

An awning is shade and light rain shelter, not a storm shelter. Every maker says the same thing in different words: guy ropes must be anchored, legs must be set, and the awning must come down in strong wind. Treat it as a fair-weather shelter and it will last for years; treat it as a storm tent and the fabric or the arms will fail.

Types of car camping awnings compared

TypeHow it worksBest forWatch out for
Pull-out side awningRolls out from the roof rack on one side, with two legs and guy ropes.A first awning, side shade for cooking and eatingCovers one side only
270-degree awningSwings around the side and back on hinged arms, with legs and guy ropes.Shade around the back and tailgate kitchenHeavier, needs a strong rack and more setup time
Rear awningMounts on the back of the vehicle and shades the tailgate area.Tailgate cooking and rear accessSmall shade area, limited use
Fixed house awningMounts to a house wall and extends on lateral arms, manual or motorised.A patio or deck at home, not a vehicleCannot mount to a roof rack

Start with a pull-out side awning if this is your first one. It is the simplest to mount, the quickest to set up, and the easiest to pack away, and it teaches the habits, pitch, guy ropes and wind sense, that every other type needs. Move to a 270-degree awning when the tailgate kitchen matters enough to carry the extra weight and setup time.

How to choose the right size

An awning is sold by two numbers: width and projection. Width is the span along the vehicle, from bracket to bracket, and projection is how far the fabric reaches out from the vehicle when it is fully extended. On a pull-out awning the first number is the width and the second is the projection, so a 6.5 by 8.2 foot awning is 6.5 feet wide along the car and reaches 8.2 feet out. Write width first, then projection, and never flip them, because an awning ordered the wrong way round will not fit.

Match the width to the roof rack, not to the car. Measure the clear run of rack where the awning will sit, and order a width equal to or just under it. Awnings come in set widths, so note the figure you need and be ready to round down rather than up. The projection decides how much shade you get: a short projection shades a chair, a long one shades a table and a kitchen, and the longest projections need the most headroom, because the fabric slopes down as it reaches out.

Leave headroom under the front edge. The fabric pitches down from the rack, so the front bar sits lower than the mounting line, and the drop grows with projection. Aim for about 7 feet of clearance under the front bar when the awning is fully out, and raise the mount or steepen the pitch if the front bar would hang lower. For a home awning the same rule applies: SunSetter recommends mounting as high on the wall as possible, with a recommended mounting height of 9 feet, and a minimum pitch that sheds rain instead of ponding it.

Think about the sun, not just the size. Awnings shade best when the sun is high, and the shade moves as the sun moves, so a 10 foot projection can still leave the table in sun at evening. Size for the worst hour you actually use the camp, usually late afternoon, not for noon. If the camp faces west, a deeper projection earns its keep; if the camp faces north, a shorter one is enough.

Measure twice, and write the figures down. Measure the rack run in two places, because racks taper, and measure the height from the rack to the ground, because that decides the leg length and the pitch. If the awning will also shade a patio at home, the measuring principle is the same one 1800 Awnings uses for house awnings: measure the area, then add about 8 inches on either side for width and at least 24 inches to the depth for projection, so the fabric covers the whole area with room to spare.

Tools and materials you need

Most pull-out awnings ship with the brackets, bolts, guy ropes and pegs in the box, and the fitting instructions list the tools. The usual kit is a 10mm socket or spanner for the mounting bolts, a 6mm Allen key, a tape measure, a level, a marker, and a second person, because lifting an awning onto a roof rack alone is how racks get scratched and fingers get trapped. ARB fitting instructions list a 10mm spanner and a 6mm Allen key for its touring awning kit, and its heavy-duty mount adds a 13mm spanner and a 4mm hex key. The TrailTacoma install of the ARB touring awning used a 10mm socket and an Allen key.

Before you start, check the roof rack itself. The rack must be rated for the awning weight plus the load it already carries, and the brackets must suit the rack: basket racks, flat racks and roof bars take different brackets, and some racks need adapter plates from the rack maker. Check the rack maker guidance before ordering brackets, because a bracket that does not fit the rack is the most common reason a DIY install stalls. An adjustable wrench works in place of a spanner for the mounting bolts; see our guide to the Best Adjustable Wrench for what to look for in one.

Keep the small extras in the camp kit: spare pegs, a mallet, a short length of cord, a soft brush for the fabric, and a dry bag for the guy ropes. A portable air compressor in the camp kit keeps tyres right after a rough track, and a jump starter covers a flat battery at a remote camp. See our guides to the Best Garage Storage and the Best Tool Storage for the rest of the camp kit.

How to mount an awning on a roof rack

Read the maker instructions for your awning before you touch a bolt, because brackets, torque figures and spacing differ between makers. The steps below follow the common pattern in the ARB and Overland Vehicle Systems instructions, and they assume a pull-out awning on a roof rack. Work with a second person throughout, and do the whole job on level ground with the car parked and the handbrake on.

First, choose the side and the position. Most campers mount on the side away from the exhaust and the fuel filler, usually the passenger side, where the kitchen sits. Slide the mounting bolts into the channels on the back of the awning and space the brackets in pairs, front, middle and rear, so they line up with the rack slots. ARB mount guidance says to position the brackets as far apart as practical, and its quick-release mounts use M6 bolts at 9Nm and M8 bolts at 22Nm. Overland Vehicle Systems lists 200 inch-pounds, or 17 foot-pounds, for its 270-degree awning brackets.

Next, fit the brackets to the rack. On a basket rack the brackets clamp around the bars, and ARB instructions wrap adhesive strip around the bars first to protect them. On a flat rack the brackets bolt to the dovetail or the cross beams. Tighten to the maker torque figure with a torque wrench, not by feel, because an over-tightened bolt strips the channel and an under-tightened one works loose on corrugated roads. Check the door and window clearance before you tighten fully, because an awning that blocks a door is a fault you find too late. If the brackets have already marked the rack bars, see our guide to Best Car Buffer for Scratches for how to deal with the marks.

Then lift the awning onto the brackets. With a helper, lift it level, pass the nuts through the keyholes or slots on the mounts, and slide it down into place. Position it so it will not interfere with doors, then adjust the brackets so they are evenly spaced from the rack and tighten all bolts. Check the whole unit by pulling it firmly by hand: it should not shift on the rack at all. If it moves, loosen, reposition and tighten again.

Finally, test the deployment before the first trip. Unzip the cover, release the straps, roll the awning out, drop the legs and set the pitch, then peg the guy ropes and leave it up for an hour. Check the brackets again after the test, and again after the first rough road, because fasteners and fixing connections should be checked regularly on both the awning and the roof rack. The Rhino-Rack Batwing install report notes the whole mounting job took about 30 minutes, and it recommends a second pair of hands.

Choosing where to park and set up

Where the car parks decides how well the awning works. Park on level ground if you can, because a car parked on a slope makes the awning pitch uneven and the legs different lengths, and a slope also sends rainwater toward the low side. Face the awning side away from the prevailing wind, so the fabric is sheltered by the vehicle itself, and away from the afternoon sun if the camp will be used in the evening. Check the ground under the awning before you set up: flat, firm ground takes pegs well, while soft sand or loose gravel needs longer pegs or sand bags to hold the guy ropes.

Think about what goes under the awning before you roll it out. The kitchen usually sits closest to the vehicle, where the shade is deepest and the tailgate is in reach, and the chairs go further out, where the breeze is. Keep the cooking area clear of the fabric and the guy ropes, because a stove under low fabric is a fire risk and a guy rope across a walkway is a trip hazard at night. Mark the guy rope lines with a light or a bright peg at dusk, so nobody walks into them in the dark.

Finally, check what is above and around the awning. Low branches can tear the fabric when the wind moves them, and a branch that drips sap or bird mess will stain it. Park clear of dead branches, and leave room for the awning to swing out fully without hitting a fence, a wall or another vehicle. A minute spent choosing the spot saves an hour of fighting a badly placed awning.

Setting up and packing away

Setting up a pull-out awning takes a few minutes once the routine is learned. Unzip the cover and fold it over the awning body, release the straps and let the fabric drape, then roll it out to full extension and drop the legs. Set the legs so the fabric pitches down away from the vehicle, roughly 15 to 20 degrees, because a shallow pitch ponds rainwater instead of shedding it. Peg the guy ropes at about 45 degrees from the legs, pull them taut, and check the fabric is tight with no sag in the middle.

A 270-degree awning takes longer and follows its own order. Release the straps, swing the arms out one at a time, attach the tension straps to the roof rack, then set the support legs on the rafters and peg every guy rope. The Overland Vehicle Systems instructions are clear that the awning self-supports only during setup, and every rafter must be supported by a pole and anchored with guy ropes before the awning is left up. Do not skip a leg because the fabric looks tight: the wind will find the unsupported corner.

Packing away is the reverse, and the one rule is to pack it dry. Shake the fabric, brush off dirt, and let it air before rolling, because a damp awning packed away grows mould and smells. If rain forces a wet pack, unroll and dry it at home as soon as you can. Roll the fabric evenly, fold the legs in, strap it down and zip the cover, then check the brackets are still tight before driving off. If the vehicle is parked on a slope, level it before rolling the awning, because a tilted car makes the fabric roll unevenly and creases it.

Wind, rain and sun

Wind is the awning killer. Awnings are designed for general camping use under normal conditions, and every maker warns against erecting them in windy weather. The practical rule is simple: if the fabric flaps hard or the legs lift, pack the awning away. Guy ropes help, but they do not turn a fair-weather shelter into a storm shelter, and a gust that catches a fully extended awning can bend arms, tear fabric or pull brackets off the rack.

Rain needs pitch. Awnings shed rain when the fabric slopes enough for water to run off, and they pond when the pitch is too shallow. Set the pitch at 15 degrees or steeper, keep one side slightly lower than the other so water has a path, and never let a pool form in the middle of the fabric, because the weight of pooled water can tear the fabric or bend the arms. In heavy rain, lower one leg further to make a clear run-off corner.

Sun is what the awning is for, but it is also what wears it out. Ultraviolet light fades fabric and weakens stitching over years, so store the awning out of the sun when it is not in use, and keep the cover zipped on the rack. At camp, the shade moves with the sun, so expect to shift chairs and the kitchen through the day rather than expecting the awning to hold the shade still.

Care and maintenance

Clean the fabric with a soft brush and clean water, and let it dry fully before packing. Do not use a pressure washer on awning fabric, because it drives water into the coating and can damage the stitching. Treat small tears early with a fabric repair patch, and check the stitching along the legs and the guy rope points each season, because those are the points that carry the load.

Check the mounting hardware every few trips. Fasteners work loose on corrugated roads, and the maker instructions for both ARB and Overland Vehicle Systems say to check fasteners and fixing connections regularly on both the awning and the roof rack, with more frequent checks after prolonged travel on uneven or corrugated terrain. Re-torque to the maker figures, replace any bolt that shows rust or stripped threads, and keep a spare set of the mounting bolts in the camp kit. A borescope helps inspect inside the roller tube and the rack channels for rust and trapped dirt; see our guide to Best Automotive Borescope for Mechanics for what to look for.

Store the awning dry, zipped and out of the sun. If the vehicle sits for months, check the cover for mould and the fabric for damp, and air it on a dry day. A little care between trips is what separates an awning that lasts a decade from one that fails in its second season. For the rest of the camp storage, see our guides to Best Storage Bins and Best Mud Flaps.

Safety essentials

  • Never leave an awning up in strong wind, pack it away first
  • Work with a second person when lifting the awning onto the rack
  • Torque mounting bolts to the maker figures, never by feel
  • Peg every guy rope, and check the pegs before leaving camp
  • Keep hands clear of hinged arms while a 270-degree awning swings
  • Set up warning lights around camp at night so nobody walks into a guy rope
  • Stop and seek a professional if the rack or brackets look bent

An awning is a sail bolted to a roof rack, and a sail in wind pulls hard on everything it is attached to. These rules keep the awning, the rack and the people under it safe.

Troubleshooting

If the awning will not sit right, check the mounting and the pitch before blaming the fabric. See our guides to Best All-Season Tires Under 100 and Best Car Buffer for Home Use for the tools that help with a roof rack job.

SymptomLikely causeFix
Awning shifts on the rackBrackets loose, or wrong bracket for the rackRe-torque to the maker figure, or fit the correct bracket
Fabric sags in the middlePitch too shallow, or guy ropes slackSteepen the pitch and re-tension the guy ropes
Water pools on the fabricPitch below 14 degrees, or one side levelLower one leg to make a run-off corner
Legs will not stay upLeg locks worn, or ground too soft for pegsReplace the locks, or move pegs to firmer ground
Awning blocks a doorMounted too far forward or too lowLoosen, reposition and re-torque the brackets
Mould smell after storagePacked away dampUnroll, clean and dry fully before packing again

Who should NOT DIY this

Do not DIY the mount if your roof rack is not rated for the awning. A rack that cannot carry the weight will flex, and the awning will work the brackets loose on the first rough road. Check the rack load rating first, and if the numbers do not cover the awning, fit a stronger rack or have a professional fit it. Best Hard Tonneau Cover Under 500

Do not mount a 270-degree awning alone. It is heavier than a pull-out awning, the arms swing wide, and one person cannot hold it level while tightening brackets. The maker instructions recommend an experienced aftermarket fitter for the 270-degree mount, and a second person is the minimum for a safe DIY job. Best Tow Ropes Under 100

Do not drill into the vehicle roof to fit an awning. Roof racks and rain gutters are the mounting points, not the roof skin, and a drilled hole leaks and rusts. If the vehicle has no rack and no rails, fit a proper rack first, or have a fitter advise on the right mounting system. Best Performance Monitors Under 100

Do not leave the awning up while you drive away from camp. It must be packed, strapped and zipped before the vehicle moves, because an open awning at road speed tears off and endangers other road users. Check the cover and the straps before every departure. Best Garage Security Cameras Under 100

Final verdict

A pull-out awning is the right first DIY awning: simple to mount, quick to set up, and forgiving to learn on. A 270-degree awning is the upgrade for a tailgate kitchen, once the rack, the weight and the setup routine are all understood. Whichever type you choose, mount it to the maker torque figures, pitch it so water runs off, peg every guy rope, and pack it away before the wind rises. Keep the maker instructions and the torque figures in the glovebox, because the next time the awning comes off the rack, for a repair or a different vehicle, the same figures apply. If one sentence had to carry the whole job, it would be this: mount it right, pitch it right, and pack it away before the wind rises.

FAQ

Can I install a car camping awning myself?

Yes, most pull-out awnings are a DIY job with basic tools, a second person and the maker instructions. The usual tools are a 10mm socket, a 6mm Allen key, a tape measure and a level, and the ARB touring awning install needs a 10mm spanner and a 6mm Allen key. A 270-degree awning is heavier and the maker recommends an experienced fitter, so get help or book a professional for that type.

How do I choose the awning size for my car?

Measure the clear run of roof rack where the awning will sit, and order a width equal to or just under it. The projection decides the shade: a short projection shades a chair, a long one shades a table and a kitchen. Awnings come in set widths, so be ready to round down rather than up, and never flip width and projection when ordering.

What torque do awning mounting bolts need?

Use the maker figures for your awning, because they differ between makers. ARB lists M6 bolts at 9Nm and M8 bolts at 22Nm for its awning mounts, and Overland Vehicle Systems lists 200 inch-pounds, or 17 foot-pounds, for its 270-degree awning brackets. Always use a torque wrench, and re-check the bolts after the first rough road.

How much pitch does an awning need?

Set the pitch at 15 degrees or steeper, because a shallow pitch ponds rainwater instead of shedding it. Most residential awnings adjust between 14 and 35 degrees, so 14 degrees is the practical minimum. Keep one side slightly lower than the other so water has a clear run-off corner, and never let a pool form in the middle of the fabric.

Can I leave my awning up in the wind?

No. Awnings are designed for general camping use under normal conditions, and every maker warns against erecting them in windy weather. If the fabric flaps hard or the legs lift, pack the awning away. Guy ropes help in a breeze, but they do not turn a fair-weather shelter into a storm shelter.

How do I keep my awning from pooling water in rain?

Steepen the pitch to at least 15 degrees and lower one leg further to make a run-off corner, so water has a path off the fabric. Check the guy ropes are taut, because slack ropes let the fabric sag and hold water. In heavy rain, pack the awning away rather than letting a pool form, because pooled water can tear fabric or bend arms.

Do I need a roof rack to mount an awning?

Yes, in practice. Awnings mount to a roof rack, roof bars or a basket rack with maker brackets, and some racks need adapter plates. If the vehicle has no rack, fit a proper rack first. Do not drill into the roof skin, and do not mount to a spare tyre carrier or a ratchet strap, because neither holds an awning safely at camp or on the road.

How do I clean and store my awning?

Brush the fabric clean with water and a soft brush, and let it dry fully before packing, because a damp awning grows mould. Never use a pressure washer on awning fabric. Store it dry, zipped and out of the sun, and check the mounting bolts and the stitching each season. If rain forces a wet pack, unroll and dry it at home as soon as you can.

What is the difference between a pull-out and a 270-degree awning?

A pull-out awning rolls out from one side of the vehicle and shades that side, with two legs and guy ropes. A 270-degree awning swings around the side and the back on hinged arms, so it shades the rear and a tailgate kitchen as well. The 270-degree type is heavier, costs more, takes longer to set up, and needs a stronger rack.

Sources

By Leo, Founder, WinchInsider

Leo researches winches and automotive accessories from maker documents, listing evidence and owner reports, and writes every guide so a first-time buyer can choose with confidence.

Related guides

Leave a Comment