A wiring kit and a connector kit solve different problems, and buying the wrong one is the most common mistake in car wiring. A wiring kit gives you a complete circuit, relay, fuse, switch and wire, ready to power a light bar. A connector kit gives you the joints, the splices and terminals that join wires together.
The rule is simple. If you are adding a new accessory, a light bar, a pod or a fan, buy a wiring kit. If you are repairing a wire, extending a harness or joining two wires, buy connectors. Most real jobs need both, and this guide covers both sides.
This guide compares three Nilight wiring harnesses against a Wirefy solder seal kit and a TICONN crimp kit, with the gauge, the seal and the install time for each, so you can pick the right side for your job.
The 30-second answer
Buy a wiring kit if you are adding a new accessory, and buy connectors if you are repairing or joining wires. The Nilight 10036W harness is the pick for a new light bar, because it gives a 14 gauge, 11.5 ft, 2-lead circuit with a relay and a fuse in one box. Nilight 10036W 14AWG Wiring Harness Kit 2-Lead DT Check Price Nilight 10018W 14AWG Wiring Harness Kit 1-Lead DT Check Price Nilight 10016W 16AWG Wiring Harness Kit 2-Lead DT Check Price Wirefy Solder Seal Wire Connectors Kit 110 Pieces Check Price TICONN Heat Shrink Wire Connectors Kit 120 Pieces Check Price The honest limit is that neither side replaces the other. A harness cannot splice a broken wire, and a connector kit cannot power a new light bar, so a full install usually needs one of each, and the cheapest way to do a job right is to buy the right one first.
How we researched this guide
We compared wire gauge, length, connector type, seal rating and install method across three wiring harnesses and two connector kits, then checked every Amazon listing live through the Creators API before recommending it.
Our quick picks
Best Wiring Kit
Nilight 10036W 14AWG Wiring Harness Kit 2-Lead DT
A 14 gauge, 11.5 ft, 2-lead harness with a relay and fuse, for two lights on one circuit.
Best Single Light Harness
Nilight 10018W 14AWG Wiring Harness Kit 1-Lead DT
A 14 gauge, 12 ft, 1-lead harness for a single light bar, rated to 300 watts.
Best Budget Harness
Nilight 10016W 16AWG Wiring Harness Kit 2-Lead DT
A 16 gauge, 12 ft, 2-lead harness for two smaller lights, at the lowest cost here.
Best Connector Kit
Wirefy Solder Seal Wire Connectors Kit 110 Pieces
110 solder seal connectors for 26 to 10 gauge wire, waterproof, for splices that must never leak.
Best Crimp Kit
TICONN Heat Shrink Wire Connectors Kit 120 Pieces
120 crimp connectors for 22 to 10 gauge wire, with 3 to 1 shrink, for fast, cheap splices.
Quick comparison
| Product | Wire Gauge | Use | Warranty | Check Price |
|---|---|---|---|---|
| Nilight 10036W 14AWG Wiring Harness Kit 2-Lead DT | 14 AWG, 180W | Two lights, one circuit | See listing for details. | Check Price |
| Nilight 10018W 14AWG Wiring Harness Kit 1-Lead DT | 14 AWG, 300W | One large light bar | See listing for details. | Check Price |
| Nilight 10016W 16AWG Wiring Harness Kit 2-Lead DT | 16 AWG, 180W | Two smaller lights | See listing for details. | Check Price |
| Wirefy Solder Seal Wire Connectors Kit 110 Pieces | 26 to 10 AWG | Splices that must stay dry | See listing for details. | Check Price |
| TICONN Heat Shrink Wire Connectors Kit 120 Pieces | 22 to 10 AWG | Fast splices and terminals | See listing for details. | Check Price |
How to Choose Between Wiring Kits and Connectors
Ask what the job is first
A new accessory needs a wiring kit, because it needs a complete circuit with a relay, a fuse and a switch. A repair or a splice needs connectors, because it needs a joint between two wires. If you are adding a light bar, buy a harness. If you are fixing a broken wire, buy connectors. Most real jobs need one of each, so buy the right one for the job, not the one that looks cheaper.
Match the gauge to the watts
Fourteen gauge wire carries 180 watts on a 2-lead harness and 300 watts on a 1-lead harness, while 16 gauge wire carries 180 watts on a 2-lead harness. Check the light wattage before ordering, because a harness that is too thin for the lights will drop voltage and heat up. A connector must match the wire gauge too, so check the gauge range on the kit before buying. Best Adjustable Wrench
Pick the seal for the location
A splice in the engine bay, under the car or in a door needs a waterproof seal, because water and salt corrode an open joint within a year. A solder seal gives the best waterproof joint, while a crimp with 3 to 1 shrink is good for a dry or covered joint. Match the seal to the location, not to the cheapest kit, because a corroded joint costs more to fix than a sealed one costs to buy.
Check the connector type
A light bar with a DT plug needs a DT harness, and a light with a different plug needs an adapter or a different harness. A connector kit must match the terminal style you need, whether it is a ring, a fork, a spade or a butt splice. Check the plug and the terminal style before ordering, because a harness with the wrong plug is a harness you cannot use. Best All-Season Tires Under 200
Count the leads before you buy
A 2-lead harness powers two lights from one circuit, while a 1-lead harness powers one light. A connector kit with 110 pieces covers a full rewire, while a small kit covers a single repair. Count the lights and the splices before ordering, because a harness with too few leads means another harness, and a kit with too few connectors means another order. Best Garage Security Cameras Under 100
Use the right tool for the joint
A solder seal needs a heat gun, and a crimp needs a ratchet crimper with the right die. A joint made with the wrong tool is a joint that fails, whether it is a solder seal heated with a lighter or a crimp squeezed with pliers. Buy or borrow the right tool before you start, and practice on a spare wire, because a clean joint is a joint that lasts. Best Garage Storage
Budget Guide
| Tier | What you get | Example pick |
|---|---|---|
| Entry | A 16 gauge 2-lead harness for two smaller lights, or a 120-piece crimp kit for fast repairs. Fine for pods, small bars and a single repair. | Nilight 10016W 16AWG Wiring Harness Kit 2-Lead DT |
| Mid-range | A 14 gauge harness for a pair of lights, or a 110-piece solder seal kit for waterproof splices. The picks in this guide sit here, and they cover most installs. | Nilight 10036W 14AWG Wiring Harness Kit 2-Lead DT |
| Premium | A 14 gauge 1-lead harness rated to 300 watts for a single large bar, plus a full solder seal kit and a full crimp kit for the workshop. The most complete setup, for a full rewire. | Nilight 10018W 14AWG Wiring Harness Kit 1-Lead DT |
Wiring Kits vs Connectors Compared
| Type | How it works | Best for | Watch out for |
|---|---|---|---|
| Wiring harness | Complete circuit, relay, fuse, switch | New accessory, light bar | Cannot splice a broken wire |
| Solder seal | Solder and seal in one heat step | Wet splices, repairs | Needs a heat gun, slower per joint |
| Crimp | Cold weld, fast, handles vibration | Fast repairs, terminals | Seal is good, not best in water |
| DT connector | Waterproof plug, light bars | Light bar harness | Needs a matching plug |
Detailed reviews
Each kit below was checked against its listed gauge, length and connector type and its Amazon listing, live, before it earned a place in this guide. The reviews focus on gauge, seal and install method, because those three things decide whether a circuit works or a joint fails.
Best Wiring Kit: Nilight 10036W 14AWG Wiring Harness Kit 2-Lead DT
Best Wiring Kit
Why the Nilight 10036W is our pick
The Nilight 10036W is the best wiring kit here, because it powers two lights from one circuit with everything included. Fourteen gauge wire carries 180 watts, which suits a pair of light bars or pods, and the 11.5 ft length reaches from the battery to the front of most cars and trucks. The DT connectors are waterproof, the relay handles the switching, and the fuse protects the circuit, so the whole install is one box and one afternoon. The 2-lead design suits a pair of lights, and the DT connectors suit a light bar with a DT plug. Owners report the harness being the part that made a light bar install easy, because the relay, fuse and switch are all in the box. The honest limit is the gauge: 14 gauge suits 180 watts, and a bigger light bar needs a heavier harness, so check the watts before ordering.
Nilight 10036W key specs
- Gauge: 14 AWG
- Length: 11.5 ft
- Leads: 2, DT connectors
- Power: 180 watts
- Relay: Included, with fuse
- Switch: Included, see listing
- Connectors: DT, waterproof
- Use: Two light bars or pods
- Install: One box, one afternoon
- Warranty: See listing for details
- Skill level: Basic wiring needed
- Listing: Sold as a single harness kit
Nilight 10036W: fits and best for
Buyers adding a pair of lights, especially anyone fitting two light bars or pods on a car, truck or SUV. The 2-lead design suits a pair, and the 14 gauge wire suits 180 watts. Check the light wattage before ordering, because a bigger bar needs a heavier harness, and check the light plug, because this harness uses DT connectors.
Nilight 10036W pros and watch-outs
- Powers two lights from one circuit
- Relay, fuse and switch included
- DT connectors are waterproof
- 11.5 ft reaches the front of most vehicles
- Good for a first light bar install
- 14 gauge limits the watts to 180
- DT connectors only, no other plug
- Needs basic wiring skill
- Two leads, not one, so plan the routing
Nilight 10036W: what owners report
Owners say the harness is the part that made a light bar install easy, because the relay, fuse and switch are all in the box.
The common complaint is the gauge. Owners who fitted a bigger light bar report the 14 gauge wire being the limit, so check the watts first.
Nilight 10036W: who should not buy
Skip it if you are only repairing a wire, where a connector kit is the honest choice.
Nilight 10036W: pair it with
Pair it with a solder seal connector kit, so any splice in the harness is sealed against water.
We may earn a commission at no cost to you.
Route the harness away from hot exhaust parts and moving suspension, and secure it with cable ties. Best Hard Tonneau Cover Under 500
Best Single Light Harness: Nilight 10018W 14AWG Wiring Harness Kit 1-Lead DT
Best Single Light Harness
Why the Nilight 10018W is our pick
The Nilight 10018W is the single-light harness, because it gives one lead with a 300 watt rating, which suits a single large light bar better than a 2-lead harness. Fourteen gauge wire at 12 ft reaches from the battery to the front of most vehicles, and the DT connector suits a light bar with a DT plug. The relay handles the switching, the fuse protects the circuit, and the switch is included, so the install is one box and one afternoon. Owners report the harness handling a single large bar without voltage drop, and the 300 watt rating giving headroom over the 180 watt 2-lead harness. The honest limit is the lead count: one lead means one light, so a pair of lights needs the 2-lead harness instead, and the 14 gauge wire is the limit for very large bars.
Nilight 10018W key specs
- Gauge: 14 AWG
- Length: 12 ft
- Leads: 1, DT connector
- Power: 300 watts
- Relay: Included, with fuse
- Switch: Included, see listing
- Connectors: DT, waterproof
- Use: One large light bar
- Install: One box, one afternoon
- Warranty: See listing for details
- Skill level: Basic wiring needed
- Listing: Sold as a single harness kit
Nilight 10018W: fits and best for
Buyers fitting a single large light bar, especially anyone who wants a 300 watt rating on one circuit. The 1-lead design suits one bar, and the 14 gauge wire suits a large bar with headroom. Check the light wattage before ordering, because a bar over 300 watts needs a heavier harness, and check the light plug, because this harness uses DT connectors.
Nilight 10018W pros and watch-outs
- 300 watt rating, most headroom here
- One lead, simple routing
- Relay, fuse and switch included
- DT connector is waterproof
- 12 ft reaches the front of most vehicles
- One lead only, no second light
- DT connectors only, no other plug
- 14 gauge is the limit for very large bars
- Needs basic wiring skill
Nilight 10018W: what owners report
Owners say the harness handles a single large bar without voltage drop, and the 300 watt rating gives headroom over the 2-lead harness.
The common complaint is the lead count. Owners who added a second light report needing another harness, so plan the light count first.
Nilight 10018W: who should not buy
Skip it if you are fitting two lights, where the 2-lead 10036W is the honest choice.
Nilight 10018W: pair it with
Pair it with a solder seal connector kit, so any splice in the harness is sealed against water.
We may earn a commission at no cost to you.
Route the harness away from hot exhaust parts and moving suspension, and secure it with cable ties. Best Mud Flaps
Best Budget Harness: Nilight 10016W 16AWG Wiring Harness Kit 2-Lead DT
Best Budget Harness
Why the Nilight 10016W is our pick
The Nilight 10016W is the budget harness, because it gives the same 2-lead DT design as the 10036W in a lighter 16 gauge wire, which suits two smaller lights at a lower cost. Sixteen gauge wire carries 180 watts, which suits a pair of pods or a small light bar, and the 12 ft length reaches from the battery to the front of most vehicles. The DT connectors are waterproof, the relay handles the switching, and the fuse protects the circuit, so the install is one box and one afternoon. Owners report the harness being the cheapest way to wire a pair of pods, and the 16 gauge wire being enough for the lights they fitted. The honest limit is the gauge: 16 gauge is thinner than 14 gauge, so it suits smaller lights only, and a pair of large bars needs the 14 gauge harness instead.
Nilight 10016W key specs
- Gauge: 16 AWG
- Length: 12 ft
- Leads: 2, DT connectors
- Power: 180 watts
- Relay: Included, with fuse
- Switch: Included, see listing
- Connectors: DT, waterproof
- Use: Two smaller lights or pods
- Install: One box, one afternoon
- Warranty: See listing for details
- Skill level: Basic wiring needed
- Listing: Sold as a single harness kit
Nilight 10016W: fits and best for
Budget buyers fitting two smaller lights, especially anyone wiring a pair of pods or a small light bar. The 2-lead design suits a pair, and the 16 gauge wire suits 180 watts at a lower cost. Check the light wattage before ordering, because a pair of large bars needs the 14 gauge harness, and check the light plug, because this harness uses DT connectors.
Nilight 10016W pros and watch-outs
- Lowest cost 2-lead harness here
- Same DT waterproof connectors
- Relay, fuse and switch included
- 12 ft reaches the front of most vehicles
- Good for pods and small bars
- 16 gauge suits smaller lights only
- Thinner wire, less headroom
- DT connectors only, no other plug
- Needs basic wiring skill
Nilight 10016W: what owners report
Owners say the harness is the cheapest way to wire a pair of pods, and the 16 gauge wire is enough for the lights they fitted.
The common complaint is the gauge. Owners who fitted a pair of large bars report the 16 gauge wire being the limit, so check the watts first.
Nilight 10016W: who should not buy
Skip it if you are fitting large bars, where the 14 gauge 10036W is the honest choice.
Nilight 10016W: pair it with
Pair it with a solder seal connector kit, so any splice in the harness is sealed against water.
We may earn a commission at no cost to you.
Route the harness away from hot exhaust parts and moving suspension, and secure it with cable ties. Best Performance Monitors Under 100
Best Connector Kit: Wirefy Solder Seal Wire Connectors Kit 110 Pieces
Best Connector Kit
Why the Wirefy Solder Seal is our pick
The Wirefy solder seal kit is the best connector kit here, because it gives 110 connectors that solder and seal in one heat step. Each connector carries a solder ring and a dual-walled shrink sleeve, so heating it with a heat gun melts the solder around the wires and shrinks the sleeve into a waterproof seal at the same time. The kit covers 26 to 10 gauge wire, which suits almost every automotive circuit, and the waterproof seal suits splices in the engine bay, under the car and in the doors, where water and salt would corrode an open crimp. The honest limit is the heat: a solder seal needs a heat gun, and a joint heated badly can melt insulation or leave a cold solder joint, so practice on a spare wire first.
Wirefy Solder Seal key specs
- Pieces: 110 connectors
- Gauge: 26 to 10 AWG
- Type: Solder seal, heat shrink
- Seal: Waterproof, adhesive-lined sleeve
- Use: Splices, repairs, extensions
- Tool: Heat gun needed
- Solder: Low-temp solder ring, melts on heating
- Install: One heat step, solder and seal together
- Warranty: See listing for details
- Skill level: Basic, practice first
- Listing: Sold as a 110-piece kit
- Coverage: Most automotive wire gauges
Wirefy Solder Seal: fits and best for
Buyers repairing or extending wires, especially anyone splicing in the engine bay, under the car or in a door, where water and salt corrode an open joint. The 110-piece kit suits a full rewire or a workshop, and the solder seal suits splices that must never leak. Check that you have a heat gun before ordering, because a solder seal needs even heat to melt the solder and shrink the sleeve.
Wirefy Solder Seal pros and watch-outs
- Solder and seal in one heat step
- Waterproof, adhesive-lined sleeve
- Covers 26 to 10 gauge wire
- 110 pieces, good for a full rewire
- Stops corrosion in wet splices
- Needs a heat gun
- Bad heating can melt insulation
- Slower than a crimp per splice
- Practice needed for a clean joint
Wirefy Solder Seal: what owners report
Owners say the connectors are the fix for a splice that kept failing, because the solder and the seal together stop corrosion.
The common complaint is the heat. Owners who used a lighter instead of a heat gun report melted insulation, so use a proper heat gun.
Wirefy Solder Seal: who should not buy
Skip it if you need a fast crimp on a dry indoor circuit, where the TICONN crimp kit is the honest choice.
Wirefy Solder Seal: pair it with
Pair it with a Nilight wiring harness, so any splice in the harness is sealed against water.
We may earn a commission at no cost to you.
Practice on a spare wire first, and heat evenly until the solder flows and the sleeve shrinks fully. Best Storage Bins
Best Crimp Kit: TICONN Heat Shrink Wire Connectors Kit 120 Pieces
Best Crimp Kit
Why the TICONN Crimp is our pick
The TICONN crimp kit is the best crimp kit here, because it gives 120 connectors in ring, fork, spade and butt styles, for 22 to 10 gauge wire, with a 3 to 1 heat shrink that seals the joint after crimping. A crimp is a cold weld: the terminal is compressed around the wire with a crimper, which makes a gas-tight joint that handles vibration without heating the wire, and the heat shrink adds a seal against water. The kit suits a fast repair, a terminal replacement or a new circuit, and the 120 pieces cover a full rewire. The honest limit is the seal: a crimp with shrink is good, but a solder seal is better in a wet splice, so use the TICONN kit for dry or covered joints and the Wirefy kit for wet ones.
TICONN Crimp key specs
- Pieces: 120 connectors
- Gauge: 22 to 10 AWG
- Styles: Ring, fork, spade, butt
- Shrink: 3 to 1 heat shrink
- Type: Crimp, cold weld
- Use: Fast repairs, terminals, new circuits
- Tool: Ratchet crimper needed
- Install: Crimp, then shrink the sleeve
- Warranty: See listing for details
- Skill level: Basic, crimper needed
- Listing: Sold as a 120-piece kit
- Coverage: Most automotive wire gauges
TICONN Crimp: fits and best for
Buyers who want the fastest way to join wires, especially anyone doing a repair, a terminal replacement or a new circuit on a dry or covered joint. The 120-piece kit suits a full rewire, and the crimp suits a joint that must handle vibration. Check that you have a ratchet crimper before ordering, because a crimp needs the right tool to be gas-tight.
TICONN Crimp pros and watch-outs
- Fastest joint here, seconds per crimp
- 120 pieces, four terminal styles
- 3 to 1 shrink seals the joint
- Cold weld handles vibration
- Good for a full rewire
- Seal is good, not as good as solder seal in wet joints
- Needs a ratchet crimper
- Wrong die size gives a weak crimp
- Open ends need shrink to seal
TICONN Crimp: what owners report
Owners say the crimps are the fastest way to join wires, because a crimp takes seconds with a ratchet crimper, and the 3 to 1 shrink seals the joint well.
The common complaint is the tool. Owners who used pliers instead of a ratchet crimper report weak crimps that pulled out, so use the right crimper.
TICONN Crimp: who should not buy
Skip it if the splice will sit in water, where the Wirefy solder seal kit is the honest choice.
TICONN Crimp: pair it with
Pair it with a Nilight wiring harness, so the harness terminals are crimped properly.
We may earn a commission at no cost to you.
Use a ratchet crimper with the right die, and shrink the sleeve fully after crimping. Best Tool Storage
Spec comparison
| Spec | Nilight 10036W | Nilight 10018W | Nilight 10016W | Wirefy Solder Seal | TICONN Crimp |
|---|---|---|---|---|---|
| Nilight 10036W | 14 AWG | 11.5 ft | 2-lead DT | 180 watts | |
| Nilight 10018W | 14 AWG | 12 ft | 1-lead DT | 300 watts | |
| Nilight 10016W | 16 AWG | 12 ft | 2-lead DT | 180 watts | |
| Wirefy Solder Seal | 26 to 10 AWG | 110 pieces | Solder seal | Waterproof | |
| TICONN Crimp | 22 to 10 AWG | 120 pieces | Crimp | 3 to 1 shrink | |
| Gauge rule | 14 AWG | 180 watts, 2-lead | 300 watts, 1-lead | Check the watts | |
| Seal rule | Solder seal | Best in water | Crimp plus shrink | Good in dry joints | |
| Tool rule | Heat gun | Solder seal | Ratchet crimper | Crimp | |
| Lead rule | 2-lead | Two lights | 1-lead | One light | |
| Best for | New light bar | Nilight 10036W | See reviews | Match kit to the job | |
| Check Price | Check Price | Check Price | Check Price | Check Price | Check Price |
How to Install a Wiring Harness and Connectors
Disconnect the battery before you start, and plan the routing from the battery to the lights, keeping the harness away from hot exhaust parts and moving suspension. Mount the relay near the battery, fit the fuse close to the battery, and run the harness along the chassis with cable ties so it cannot chafe. Connect the switch to a switched source, so the lights turn off with the ignition.
Strip the wires cleanly, without nicking the strands, and twist the strands tight before joining. For a solder seal connector, slide it over the joint, heat it evenly with a heat gun until the solder flows and the sleeve shrinks fully, then let it cool before moving it. For a crimp, use a ratchet crimper with the right die, squeeze until the ratchet releases, then shrink the sleeve fully over the joint.
Reconnect the battery, switch the lights on and check they light evenly, with no flicker and no dimming. Check the relay clicks, the fuse holds, and the switch works, then check the harness and the joints after a week for heat marks or looseness. If a joint is warm, remake it, because a warm joint is a high-resistance joint that will fail.
Safety essentials
- Disconnect the battery before you start wiring, because a live circuit can short and spark.
- Fit the fuse close to the battery, so a short in the harness blows the fuse before the wire heats up.
- Never bypass a fuse or fit a bigger one, since the wiring is rated for the original fuse and a bigger fuse can cause a fire.
- Use the right tool for the joint, because a solder seal heated with a lighter or a crimp squeezed with pliers is a joint that fails.
- Route the harness away from hot exhaust parts and moving suspension, and secure it with cable ties so it cannot chafe.
- Check the joints after a week for heat marks, and remake any joint that feels warm, because a warm joint is a high-resistance joint.
Car wiring is a high-current job, so a few habits keep the car and the installer safe. These six rules cover the mistakes that cost the most.
The TICONN 100-piece solder seal kit is a second solder seal kit for the workshop, so a splice is never left unsealed for want of a connector.
The Wirefy 540-piece crimp kit is a full workshop crimp set, for a buyer who does a lot of wiring and wants every terminal style on hand.
The Nilight 10020W switch harness is a second harness with a switch, for a buyer who wants a spare circuit for another accessory.
Troubleshooting
Most wiring problems are gauge or joint problems, and most have a simple fix. These fixes cover the ones owners report most. Warning Lights Reviews
| Symptom | Likely cause | Fix |
|---|---|---|
| Lights flicker or dim | Harness gauge too thin for the watts | Use a heavier gauge harness, or split the load across two circuits |
| Fuse blows on switching on | Short in the harness, or the fuse is too small | Check the wiring for a short, and fit the fuse rating the harness specifies |
| Joint corrodes and fails | Open joint in a wet location | Remake it with a solder seal connector and adhesive-lined shrink |
| Crimp pulls out | Wrong die size, or pliers used instead of a crimper | Use a ratchet crimper with the right die and re-crimp |
| Solder joint is cold and weak | Heated badly, solder did not flow | Reheat evenly with a heat gun until the solder flows, or remake the joint |
| Lights stay on with the ignition off | Switch wired to an unswitched source | Wire the switch to a switched source so the lights turn off with the ignition |
Who should NOT buy these
Do not buy a wiring kit to fix a broken wire. A harness gives you a new circuit, not a joint, and it cannot splice a broken wire, so a repair needs connectors, not a harness, and the cheapest way to fix a wire is to buy the right connector kit first. Best First Aid Kit Under 50
Do not buy a connector kit to power a new light bar. A connector kit gives you joints, not a circuit, and it has no relay, no fuse and no switch, so a new accessory needs a wiring harness, and the cheapest way to power a light is to buy the right harness first. ABS Scan Tools vs OBDII
Do not buy a harness by length alone if you have not checked the gauge. A 16 gauge harness suits smaller lights, while a pair of large bars needs 14 gauge, and a harness that is too thin for the watts will drop voltage and heat up, so check the watts before the length. AGM Batteries Review for Cars
Do not make a joint with the wrong tool. A solder seal heated with a lighter melts insulation, and a crimp squeezed with pliers pulls out, so buy or borrow a heat gun and a ratchet crimper before you start, because a joint made with the wrong tool is a joint that fails. AGM Batteries Cost
Final verdict
Best Wiring Kit: Nilight 10036W Check Price — The best wiring kit, for two lights on one circuit.
Best Single Light Harness: Nilight 10018W Check Price — The single-light pick, for one large bar with headroom.
Best Budget Harness: Nilight 10016W Check Price — The budget harness, for two smaller lights at the lowest cost.
Best Connector Kit: Wirefy Solder Seal Check Price — The best connector kit, for splices that must never leak.
Best Crimp Kit: TICONN Crimp Check Price — The best crimp kit, for fast joints that hold.
FAQ
What is the difference between a wiring kit and electrical connectors?
A wiring kit gives you a complete circuit, relay, fuse, switch and wire, ready to power a new accessory like a light bar. Electrical connectors give you the joints, splices and terminals that join wires together, for a repair or an extension. A new accessory needs a harness, and a repair needs connectors.
Do I need a wiring harness for a light bar?
Yes, and it is the safest way to power one. A harness gives you a relay, a fuse and a switch in one box, so the light bar gets full voltage without the current running through a small switch. Wire the harness to the battery with a fuse close to the battery, and route it away from heat and moving parts.
Are solder seal connectors better than crimp connectors?
It depends on the location. A solder seal gives the best waterproof joint, because the solder and the adhesive-lined sleeve seal the splice in one heat step, which suits wet locations. A crimp is faster per joint and handles vibration well, which suits dry or covered joints. Use solder seal in water and crimp in the dry.
What gauge wire do I need for a light bar?
It depends on the watts. A 14 gauge harness carries 180 watts on a 2-lead circuit and 300 watts on a 1-lead circuit, while a 16 gauge harness carries 180 watts on a 2-lead circuit. Check the light wattage before ordering, and buy a harness rated above the lights, so the wire never runs at its limit.
Can I use a heat gun on solder seal connectors?
Yes, and it is the right tool. Heat the connector evenly with a heat gun until the solder ring melts and the sleeve shrinks fully, then let it cool before moving it. Do not use a lighter, because it heats unevenly and melts the insulation, and practice on a spare wire first.
What is a DT connector?
A DT connector is a waterproof plug used on light bars and auxiliary lights, with a sealed housing that keeps water out. A harness with DT connectors suits a light bar with a DT plug, so check the light plug before ordering, because a harness with the wrong plug cannot be used without an adapter.
Do I need a relay for aux lights?
Yes, for any light bar or pod that draws more than a few amps. A relay lets a small switch control a high-current light without the full current running through the switch, which would overheat it. A wiring harness includes the relay, so buy a harness rather than wiring a light straight to a switch.
How do I waterproof a wire splice in a car?
Use a solder seal connector or a crimp with adhesive-lined heat shrink, and make the joint in a dry place if you can. A solder seal melts solder and shrinks a waterproof sleeve in one heat step, while a crimp with 3 to 1 shrink seals the joint after crimping. Seal every splice outside the cabin, because water corrodes an open joint within a year.
Can I crimp wires without a crimper?
No, not properly. A crimp needs a ratchet crimper with the right die to compress the terminal into a gas-tight cold weld, and pliers cannot do that. A crimp made with pliers pulls out under vibration, so buy or borrow a ratchet crimper before you start, and practice on a spare wire.
Sources
- Amazon listing: Nilight 10036W Wiring Harness Kit
- Amazon listing: Nilight 10018W Wiring Harness Kit
- Amazon listing: Nilight 10016W Wiring Harness Kit
- Amazon listing: Wirefy Solder Seal Connectors Kit 110 Pieces
- Amazon listing: TICONN Heat Shrink Wire Connectors Kit 120 Pieces
- Amazon listing: TICONN Solder Seal Wire Connectors 100 Pieces
- Amazon listing: Wirefy Heat Shrink Wire Connectors Kit 540 Pieces
- Amazon listing: Nilight 10020W Wiring Harness Kit with Switch
- SolderStick: Solder Seal vs Crimp, Which Connector Fits the Job
- Onlink Tech: Crimping vs Soldering for Automotive Wire Harness Connections
- Apex Technation: Automotive Wiring Repair, Solder, Crimp and Splice Methods
- JDE Contact: Can I Use Soldering Instead of Crimping for Car Wire Terminals
- CarRundown: Nilight 20-Inch Light Bar Kit Review
- WinchInsider: Best ATV Winch
- WinchInsider: Best Jump Starter
- WinchInsider: Best Garage Storage
By Leo, Founder, WinchInsider
Leo researches winches and automotive accessories from maker documents, listing evidence and owner reports, and writes every guide so a first-time buyer can choose with confidence.
Related guides
- AGM Batteries vs Flooded
- AGM Batteries vs Lead-Acid
- 12V Car Heaters Reviews Best Models
- 12V Car Heaters vs AC
- 12V Car Heaters vs Electric Heaters
- 12V Heater Review
Nilight 10036W 14AWG Wiring Harness Kit 2-Lead DT