Automotive Adhesives Review and Comparison: What Holds and What Fails?

Disclosure: As an Amazon Associate, I earn from qualifying purchases. This comes at no extra cost to you.

You glue a trim piece back on, wait an hour, and it falls off in your hand. Or you patch a cracked bracket with epoxy, drive to work, and find the repair has let go by lunchtime. The adhesive was not bad — it was the wrong adhesive for the job.

Epoxies, putties and super glues are not interchangeable. A steel-reinforced epoxy holds a metal bracket at 550 degrees, a putty stick fills a gap and sets in five minutes, and a rubber-toughened gel flexes with trim that moves. Buy the chemistry that matches the repair, not the tube that looks strongest.

This guide compares five automotive adhesives — two J-B Weld epoxies, a Loctite gel, a Gorilla epoxy and a 3M structural epoxy — on strength, heat, set time and where each one belongs, and names the five worth buying on Amazon. A cracked battery case is one repair where a steel epoxy earns its keep — our AGM battery reviews cover the battery types most often sealed this way. After a bracket repair, our alignment tool reviews show how to check the part sits true before the epoxy cures.

The 30-second answer

Buy the J-B Weld Original Cold-Weld 8265S for the best overall epoxy here: steel-reinforced, 5,020 PSI tensile strength, rated to 550 degrees. Buy the J-B Weld SteelStik 8267 for the best epoxy putty — a two-ounce stick that sets in five minutes and cures in one hour. Buy the Loctite Super Glue Ultra Gel Control, 2-pack for the best super glue gel — rubber-toughened, flexible, in 0.14 fluid ounce bottles. Buy the Gorilla 2-Part Epoxy for the best fast-set epoxy — a 0.85 ounce syringe with a five-minute set and a clear finish. Buy the 3M Scotch-Weld Epoxy Adhesive DP100 Clear for the best professional epoxy — 48.5 millilitres of clear structural epoxy, model DP-100. While the epoxy cures overnight, a battery tender keeps the battery topped up — our battery tender comparison covers the tenders for that job. Blow dust off the bond with compressed air before you glue — our 12-volt air compressor guide covers the portable compressors that do it.

How we researched this guide

We profiled five automotive adhesives, checked four maker documents and seven roundups and retailer sources, verified five Amazon listings, and reviewed five groups of owner reports. Five products made the slate; the comparison side covers liquid epoxies, putty sticks, super glue gels and structural epoxies, which are types, not picks. One candidate was excluded: the Permatex 84109 PermaPoxy Multi-Metal Epoxy, a real product whose Amazon ASIN could not be verified — so it is not picked.

Quick picks

Best Overall Epoxy

J-B Weld Original Cold-Weld 8265S

A steel-reinforced two-part epoxy, model 8265S, two ounces, 5,020 PSI tensile strength, rated to 550 degrees, for metal repairs that must hold.

Check Price

Best Epoxy Putty

J-B Weld SteelStik 8267

A steel-reinforced epoxy putty stick, model 8267, two ounces, that sets in five minutes and cures in one hour, for filling gaps and sealing leaks.

Check Price

Best Super Glue Gel

Loctite Super Glue Ultra Gel Control, 2-pack

A rubber-toughened super glue gel in a two-pack of 0.14 fluid ounce bottles, with a no-drip formula and a control applicator, for trim and small parts.

Check Price

Best Fast-Set Epoxy

Gorilla 2-Part Epoxy

A clear two-part epoxy in a 0.85 ounce syringe, model 4200101, with a five-minute set, for quick general repairs on many materials.

Check Price

Best Professional Epoxy

3M Scotch-Weld Epoxy Adhesive DP100 Clear

A clear structural epoxy adhesive, model DP-100, 48.5 millilitres, for professional bonds on metal, glass, ceramic and composites.

Check Price

Match an automotive adhesive to your repair

Automotive adhesive calculator — enter your own requirements

Step 1 — What are you fixing?





Quick compare

PickTypeStrengthHeat limitSet timeBest forCheck Price
J-B Weld OriginalLiquid epoxy5,020 PSI550F4-6 hr setHot metal repairsCheck Price
J-B Weld SteelStikEpoxy putty stick900 PSI lap shear350F continuous5 min setGaps, leaks, holesCheck Price
Loctite Ultra GelSuper glue gel3,000+ PSINot for heatSecondsTrim, badges, small partsCheck Price
Gorilla 2-Part EpoxyTwo-part epoxy3,300 PSI180F5 min setGeneral repairs, many materialsCheck Price
3M DP100 ClearStructural epoxyNot publishedNot publishedNot publishedProfessional structural bondsCheck Price
Permatex 84109 PermaPoxyMulti-metal epoxyNot publishedNot published4-5 min workingExcluded, no verified ASINNot a pick

How to choose an automotive adhesive

Strength

Match the strength to the load. J-B Weld Original gives 5,020 PSI for metal, SteelStik gives 900 PSI lap shear for gaps, and a gel gives a surface bond. A trim piece needs far less strength than a bracket, so do not overbuy.

Heat resistance

Check the temperature rating before you glue anything near an engine. J-B Weld Original is rated to 550 degrees, SteelStik to 350 degrees continuous, and Gorilla epoxy to about 180 degrees. A glue that softens with heat is a repair that fails.

Set time and cure time

Set time is when you can let go, and cure time is when the bond is full strength. SteelStik sets in five minutes but cures in one hour, while J-B Weld Original sets in four to six hours and cures in up to 24. Plan the job around the cure, not the set.

Gap filling

A liquid epoxy runs off a gap, while a putty fills it. SteelStik moulds into holes and leaks like clay, and a gel only bonds surfaces that touch. If the parts do not meet, buy a putty. A borescope lets you inspect a bond you cannot see — our borescope guide covers the ones mechanics use for that check. Remove trim first — our trim removal kit guide covers the kits that take trim off without breaking it.

Materials

Check the bond list. J-B Weld bonds metal, wood, plastic and ceramic, but not polyethylene, polypropylene or Teflon. Loctite gel bonds trim and small parts. A glue that does not list your material will not hold it. After gluing a sensor bracket back on, a multimeter checks the sensor still reads — our multimeter guide covers the checks. Strip rust first — our rust remover guide covers the removers that leave clean metal to glue.

Flexibility

Trim moves, so its glue must flex. The Loctite gel is rubber-toughened and bends with the part, while a rigid epoxy cracks when the trim flexes. Buy a flexible glue for trim and a rigid glue for brackets. A buffer takes the haze off a cured epoxy repair on a visible surface — our car buffer guide covers the ones that do that job. Restore faded trim after re-gluing — our trim restoration guide covers the products.

Automotive adhesives by budget

TierWhat you getExample pick
Super glue gelA fast, flexible bond for trim and small partsLoctite Ultra Gel Control, 2-pack
Fast-set epoxyA clear general repair in five minutesGorilla 2-part epoxy, 0.85 oz
Epoxy puttyA gap-filling putty that sets in five minutesJ-B Weld SteelStik 8267
Professional epoxyA clear structural bond for bigger jobs3M Scotch-Weld DP100 Clear, 48.5 mL
Strongest epoxyThe strongest metal bond in this guideJ-B Weld Original 8265S, 5,020 PSI

Types of automotive adhesive in this comparison

TypeHow it worksCapacityBest for
Liquid epoxyResin and hardener mixed and appliedHigh, up to 5,020 PSIMetal brackets and engine parts
Epoxy putty stickKneaded by hand and moulded into place900 PSI lap shearGaps, holes and leaks
Super glue gelRubber-toughened gel that sets in secondsSurface bondTrim, badges and small parts
Two-part epoxy syringeSyringe mixes resin and hardenerGeneral purposeQuick general repairs
Structural epoxyProfessional two-part adhesiveStructuralProfessional bonds on many materials

Detailed reviews: every pick, on maker evidence

Each pick below is judged on its maker documents and owner reports alone — strength, heat, set time and where its design stops being the right glue. No pick here was tested by us; the site is research-based, and every claim traces to the research notes for this article. Polish a visible repair flush once it cures — our car polisher guide covers the finishing side. For a wider epoxy comparison, see our automotive epoxy guide.

Best Overall Epoxy: J-B Weld Original Cold-Weld 8265S

Best Overall Epoxy

Why the J-B Weld Original Cold-Weld 8265S is our pick

Because it is the epoxy other epoxies are measured against. The J-B Weld Original is a steel-reinforced two-part epoxy with a tensile strength of 5,020 PSI and a temperature rating to 550 degrees once cured, so it holds metal brackets, engine parts and exhaust repairs that lesser glues cannot. It sets in four to six hours and cures fully in 15 to 24 hours, which is slow — but that slow cure is what gives it the strength. It has been the standard for metal bonding since 1969.

J-B Weld Original Cold-Weld 8265S key specs

  • Model: 8265S
  • Type: Steel-reinforced two-part epoxy
  • Size: 2 oz
  • Tensile strength: 5,020 PSI
  • Temperature: Up to 550 degrees F
  • Set time: 4 to 6 hours
  • Cure time: 15 to 24 hours
  • Colour: Dark grey
  • Bonds: Metal, wood, plastic, ceramic, concrete
  • Use: Engine, exhaust, brackets, radiators
  • Brand: J-B Weld
  • Buying channel: Verified Amazon listing, ASIN B0006O1ICE

J-B Weld Original Cold-Weld 8265S: fits and best for

Best for a metal repair that must hold under heat, vibration and load — engine parts, brackets and exhaust work.

J-B Weld Original Cold-Weld 8265S pros and watch-outs

Pros

  • 5,020 PSI tensile strength, the strongest here
  • Rated to 550 degrees for hot engine work
  • Steel-reinforced bond, nearly as hard as metal
  • Resists water, chemicals and oil

Watch-outs

  • Slow: sets in 4 to 6 hours, cures in up to 24
  • Needs careful mixing of resin and hardener
  • Dark grey colour shows on light surfaces
  • Will not bond polyethylene, polypropylene or Teflon

J-B Weld Original Cold-Weld 8265S: what owners report

  • Owners report filling a hole in a Suzuki engine case with J-B Weld, and the repair still holding — see the owner forum
  • Owners report repairs lasting 20-plus years on non-critical fittings, and warn never to use it on something seriously load-bearing — see the owner forum
  • Owners report it stopping leaks on old chrome taps, bonding a coffee table top and repairing a washing machine hinge — see the owner reviews

J-B Weld Original Cold-Weld 8265S: who should not buy

Skip it if you need a fix in minutes — this epoxy needs a day to cure. Skip it for flexible trim that moves, and skip it for plastics like polyethylene that epoxy will not bond.

J-B Weld Original Cold-Weld 8265S: pair it with

Pair it with nitrile gloves and mixing cups: the gloves keep epoxy off your skin, and the cups give you the exact one-to-one mix.

Check Price

We may earn a commission at no cost to you.

Tip: Roughen both surfaces with sandpaper and clean them before mixing, or the bond will fail.

Best Epoxy Putty: J-B Weld SteelStik 8267

Best Epoxy Putty

Why the J-B Weld SteelStik 8267 is our pick

Because some repairs need a putty, not a liquid. The SteelStik is a steel-reinforced epoxy putty stick: you cut off what you need, knead it until the colours blend, and mould it into the break like clay. It sets in five minutes, cures in one hour, and reaches 900 PSI lap shear strength, with a continuous temperature rating to 350 degrees. It fills gaps, seals leaks and rebuilds missing material where a liquid epoxy would run off.

J-B Weld SteelStik 8267 key specs

  • Model: 8267
  • Type: Steel-reinforced epoxy putty stick
  • Size: 2 oz
  • Lap shear strength: 900 PSI
  • Temperature: Continuous to 350F, intermittent to 450F
  • Set time: 5 minutes
  • Cure time: 1 hour
  • Colour: Dark grey
  • Bonds: Iron, steel, copper, brass, aluminium, bronze, fibreglass, plastic, PVC
  • Use: Gaps, leaks, holes, brackets
  • Brand: J-B Weld
  • Buying channel: Verified Amazon listing, ASIN B00RN7CT2U

J-B Weld SteelStik 8267: fits and best for

Best for a gap, a hole or a leak that needs filling and shaping, where a liquid epoxy would run off.

J-B Weld SteelStik 8267 pros and watch-outs

Pros

  • Moulds like clay and fills gaps a liquid cannot
  • Sets in five minutes, cures in one hour
  • 900 PSI lap shear strength once cured
  • Certified for potable water contact

Watch-outs

  • 900 PSI is far weaker than the Original epoxy
  • Only 350 degrees continuous, not 550
  • Messy to mix by hand
  • Dark grey shows on light surfaces

J-B Weld SteelStik 8267: what owners report

  • Owners report it sealing an exhaust leak with no leaks after, holding through rain with no rattle — see the owner reviews
  • Owners report it moulding like clay and forming to any break, nearly as hard as steel when cured — see the owner reviews
  • Owners report it holding a truck bracket through Minnesota winters with snow and road salt — see the owner reviews

J-B Weld SteelStik 8267: who should not buy

Skip it if you need maximum strength — the Original epoxy is five times stronger. Skip it for hot exhaust work over 350 degrees, and skip it if you hate kneading putty by hand.

J-B Weld SteelStik 8267: pair it with

Pair it with coarse sandpaper and a degreaser: roughen the break first, wipe it clean, and the putty grips instead of sliding off.

Check Price

We may earn a commission at no cost to you.

Tip: Knead until no streaks remain, then press it in firmly.

Best Super Glue Gel: Loctite Super Glue Ultra Gel Control, 2-pack

Best Super Glue Gel

Why the Loctite Super Glue Ultra Gel Control, 2-pack is our pick

Because trim and small parts need a glue that flexes, not one that cracks. The Loctite Ultra Gel Control is a rubber-toughened cyanoacrylate gel, so the bond bends with the part instead of snapping when the trim moves. The gel does not drip, the control applicator puts it exactly where you want it, and the two-pack gives you a spare bottle. It is the pick for interior trim, badges, small plastic parts and anything that needs a fast, neat bond.

Loctite Super Glue Ultra Gel Control, 2-pack key specs

  • Type: Rubber-toughened super glue gel
  • Size: 2-pack, 0.14 fl oz bottles
  • Formula: Gel, no-drip
  • Applicator: Control applicator
  • Flexibility: Rubber-toughened, flexible bond
  • Set time: Fast, seconds
  • Bonds: Plastic, metal, rubber, leather, wood
  • Use: Trim, badges, small parts
  • Colour: Clear
  • Brand: Loctite
  • Buying channel: Verified Amazon listing, ASIN B07VMC2YMT

Loctite Super Glue Ultra Gel Control, 2-pack: fits and best for

Best for interior trim, badges and small parts that need a fast, flexible, no-drip bond.

Loctite Super Glue Ultra Gel Control, 2-pack pros and watch-outs

Pros

  • Rubber-toughened bond flexes instead of cracking
  • Gel does not drip or run
  • Control applicator puts glue exactly where needed
  • Sets in seconds, not hours

Watch-outs

  • Not for structural or high-heat repairs
  • Small bottles run out fast on big jobs
  • Bonds skin instantly — wear gloves
  • Will not fill gaps like a putty

Loctite Super Glue Ultra Gel Control, 2-pack: what owners report

  • Owners report the gel holding a staircase trim fix under frequent use, with time to move and position the piece before it sets — see the owner reviews
  • Owners report it repairing a son’s RC car and a figurine broken in two places, holding after one drop and a 20-second hold — see the owner reviews
  • Owners warn the rest dries out in under three months even capped well, so use only a little at a time — see the owner reviews

Loctite Super Glue Ultra Gel Control, 2-pack: who should not buy

Skip it for structural repairs — a gel cannot hold a bracket. Skip it for hot engine work, and skip it for gaps; it is a surface glue, not a filler.

Loctite Super Glue Ultra Gel Control, 2-pack: pair it with

Pair it with nitrile gloves and a fine applicator nozzle: the gloves stop the gel bonding your skin, and the nozzle puts one small drop exactly where it belongs.

Check Price

We may earn a commission at no cost to you.

Tip: Use a tiny drop — more glue makes a weaker bond. For faded trim, our trim restorer guide covers the restorers that bring the colour back after the glue cures.

Best Fast-Set Epoxy: Gorilla 2-Part Epoxy

Best Fast-Set Epoxy

Why the Gorilla 2-Part Epoxy is our pick

Because sometimes you need a strong bond in minutes, not a day. The Gorilla 2-Part Epoxy comes in a syringe that mixes the resin and hardener as you squeeze, sets in five minutes, and dries clear, so the repair does not show. It bonds wood, metal, glass, ceramic and some plastics, which makes it the general-purpose pick for the jobs that are not hot enough to need J-B Weld and not small enough for a gel. The five-minute set is the feature: mix, apply, hold, done.

Gorilla 2-Part Epoxy key specs

  • Model: 4200101
  • Type: Two-part epoxy
  • Size: 0.85 oz syringe
  • Set time: 5 minutes
  • Cure time: 24 hours for full strength
  • Colour: Clear
  • Bonds: Wood, metal, glass, ceramic, some plastics
  • Use: General repairs, crafts, household
  • Temperature: 180F
  • Strength: 3,300 PSI
  • Brand: Gorilla
  • Buying channel: Verified Amazon listing, ASIN B001Z3C3AG

Gorilla 2-Part Epoxy: fits and best for

Best for a quick general repair on many materials, where a clear finish and a five-minute set matter.

Gorilla 2-Part Epoxy pros and watch-outs

Pros

  • Sets in five minutes, not hours
  • Dries clear, so the repair does not show
  • Syringe mixes resin and hardener for you
  • Bonds many materials, not just metal

Watch-outs

  • Not for hot engine work — heat resistance is limited
  • Small syringe runs out fast on big jobs
  • Full strength still needs 24 hours
  • Weaker than J-B Weld on metal

Gorilla 2-Part Epoxy: what owners report

  • Owners report assembling golf clubs with it, praising the clear finish, the low smell and a hold strong enough for the job — see the owner reviews
  • Owners report it setting up fast and holding strong once cured, doing what was needed on different repairs — see the owner reviews
  • Owners report the five-minute set suiting quick repairs, with the syringe keeping resin and hardener separate until you mix — see the owner reviews

Gorilla 2-Part Epoxy: who should not buy

Skip it for engine and exhaust work — it cannot take the heat. Skip it for structural metal repairs, and skip it if you need the strongest bond; J-B Weld is stronger.

Gorilla 2-Part Epoxy: pair it with

Pair it with a spring clamp and sandpaper: the clamp holds the parts still for the five-minute set, and the sandpaper gives the epoxy something to grip.

Check Price

We may earn a commission at no cost to you.

Tip: Hold the parts still for the full five minutes, then leave the repair alone for a day.

Best Professional Epoxy: 3M Scotch-Weld Epoxy Adhesive DP100 Clear

Best Professional Epoxy

Why the 3M Scotch-Weld Epoxy Adhesive DP100 Clear is our pick

Because 3M makes the epoxy that professionals reach for when the bond has to be structural. The Scotch-Weld DP100 Clear is a two-part epoxy adhesive in a 48.5 millilitre cartridge, model DP-100, that bonds metal, glass, ceramic and composites with a clear finish. It is the pick for a repair that must look clean and hold like a structure, from a maker whose adhesives are specified in workshops and factories. The DP100 Plus is a different product — this listing is the DP100 Clear.

3M Scotch-Weld Epoxy Adhesive DP100 Clear key specs

  • Model: DP-100
  • Type: Two-part structural epoxy
  • Size: 48.5 mL
  • Colour: Clear
  • Bonds: Metal, glass, ceramic, composites
  • Use: Structural bonds, professional repairs
  • Set time: Not published
  • Strength: Not published on the listing
  • Temperature: Not published on the listing
  • Brand: 3M
  • Buying channel: Verified Amazon listing, ASIN B0012O2EFC

3M Scotch-Weld Epoxy Adhesive DP100 Clear: fits and best for

Best for a professional repair that needs a clear structural bond on metal, glass or composites.

3M Scotch-Weld Epoxy Adhesive DP100 Clear pros and watch-outs

Pros

  • Structural epoxy from a professional maker
  • Clear finish for visible repairs
  • Bonds metal, glass, ceramic and composites
  • Larger 48.5 mL size suits bigger jobs

Watch-outs

  • No published set time, strength or temperature on the listing
  • Needs a dispensing gun or careful mixing
  • Professional cost for a small job
  • Not the pick for a five-minute fix

3M Scotch-Weld Epoxy Adhesive DP100 Clear: what owners report

  • Owners report it setting fast and hard as a rock on metal-to-metal repairs — see the owner reviews
  • Owners note the Duo-Pak needs a separate applicator and mixing nozzles — they are not in the box — see the owner reviews
  • Owners praise the clear finish for repairs that stay visible — see the owner reviews

3M Scotch-Weld Epoxy Adhesive DP100 Clear: who should not buy

Skip it if you want published numbers before you buy — the listing does not give them. Skip it for a quick fix, and skip it if a small syringe would do; this is a professional size.

3M Scotch-Weld Epoxy Adhesive DP100 Clear: pair it with

Pair it with a dispensing gun and mixing nozzles: the Duo-Pak cartridge needs both, and neither is in the box.

Check Price

We may earn a commission at no cost to you.

Tip: Mix only what you can use in the working time, and clamp the parts until it sets.

Spec comparison

SpecJ-B Weld OriginalSteelStikLoctite Ultra GelGorilla Epoxy3M DP100 Clear
TypeLiquid epoxyEpoxy putty stickSuper glue gelTwo-part epoxyStructural epoxy
Strength5,020 PSI900 PSI lap shear3,000+ PSI3,300 PSINot published
Heat limit550F350F continuousNot for heat180FNot published
Set time4-6 hr5 minSeconds5 minNot published
Cure time15-24 hr1 hrNot published24 hrNot published
Size2 oz2 oz0.14 fl oz x 20.85 oz48.5 mL
Model8265S8267Not published4200101DP-100
ColourDark greyDark greyClearClearClear
Gap fillingNo, runs offYes, moulds inNo, surface onlyNot publishedNot published
Best forHot metal repairsGaps, leaks, holesTrim, small partsGeneral repairsProfessional bonds
Check PriceCheck PriceCheck PriceCheck PriceCheck PriceCheck Price

Installation and use basics

Clean both surfaces first, then roughen them with sandpaper so the glue has something to grip. Degrease with a solvent and let the parts dry completely, because oil and moisture kill a bond. Mix a two-part epoxy exactly as the maker directs, and use only what you can apply in the working time. Press the parts together firmly, clamp them if you can, and hold them still for the full set time. Leave the repair alone for the full cure time — a bond that looks set is not yet at full strength. A rear-view mirror is held to the glass by adhesive alone — our replacement mirror guide covers the mirrors that glue back on. Mix over a mat, not the floor — our garage floor mat guide covers the ones that catch drips. Wear gloves when you mix epoxy, and keep the work area ventilated while the adhesive cures. Test the bond on a scrap piece first if the repair is structural, and do not load it until the cure time in the spec list has passed. For the stronger epoxies, our automotive epoxy under-50 guide covers the higher-strength picks.

Safety essentials

Six rules before you start work:

  • Wear gloves — super glue bonds skin instantly and epoxy irritates skin.
  • Work in fresh air — epoxy fumes and solvents are not safe to breathe all day.
  • Keep adhesives away from eyes and wash skin at once if glue touches it.
  • Never use an adhesive near a hot engine until it has fully cured.
  • Keep glues away from children and pets, and store them upright.
  • Check the bond list — no adhesive bonds every material, and some will not hold at all.

Three accessories worth having in the box:

MedPride powder-free nitrile exam gloves, medium, box of 100 — gloves keep epoxy and super glue off your skin while you mix and apply

Check Price

IRWIN QUICK-GRIP 1964758 one-handed mini bar clamp, 6 inch, 4-pack — a small clamp holds parts still for the full set time

Check Price

Custom Shop paint mixing cups, 32 ounce, box of 100 — graduated cups with one-to-one ratios give you the exact epoxy mix

Check Price

Troubleshooting

SymptomCauseFix
Bond lets go in hoursSurfaces dirty or oilyClean and roughen both surfaces, degrease, retry
Epoxy stays softWrong mix ratio or cold temperatureMix exactly as directed, warm the parts first
Putty will not stickSurfaces smooth or wetRoughen and dry the surfaces, knead until blended
Gel bonds skinNo gloves wornSoak in warm soapy water, peel gently, wear gloves next time
Repair cracks with heatGlue rated below the temperatureUse J-B Weld Original for hot work, not a gel
Clear epoxy turns cloudyMoisture in the mix or on the surfaceDry the parts fully, mix in dry air

Who should NOT buy these

If the repair is structural and hot, do not buy a gel or a fast-set epoxy. Trim glue cannot hold a bracket, and Gorilla epoxy cannot take engine heat. Buy J-B Weld Original for hot structural work. For a rusted bracket, strip the rust first — our rust remover guide covers the removers that leave clean metal to glue.

If the parts do not meet, do not buy a liquid epoxy. A liquid runs off a gap. Buy the SteelStik putty, which moulds into the hole. The same rule holds for a pedal pad that has come unstuck: a gel bonds it back.

If you need a fix in minutes, do not buy J-B Weld Original. It needs a day to cure. Buy the SteelStik or the Gorilla epoxy instead. Blow dust off the bond with compressed air first — our 12-volt air compressor reviews cover the portable compressors for that job.

If the material is polyethylene or Teflon, do not buy any epoxy here. No epoxy in this guide bonds those plastics. Buy a specialist adhesive for that material.

Final verdict

Best Overall Epoxy: J-B Weld Original Cold-Weld 8265S — 5,020 PSI and 550 degrees for metal repairs that must hold.

Check Price

Best Epoxy Putty: J-B Weld SteelStik 8267 — five-minute set and one-hour cure for gaps, holes and leaks.

Check Price

Best Super Glue Gel: Loctite Super Glue Ultra Gel Control, 2-pack — rubber-toughened gel with a control applicator for trim and small parts.

Check Price

Best Fast-Set Epoxy: Gorilla 2-Part Epoxy — five-minute set and a clear finish for quick general repairs.

Check Price

Best Professional Epoxy: 3M Scotch-Weld Epoxy Adhesive DP100 Clear — clear structural epoxy, 48.5 millilitres, for professional bonds.

Check Price

And the Permatex 84109 PermaPoxy? It is a real multi-metal epoxy, but its Amazon ASIN could not be verified in this research, so it is not picked. Every pick above has a verified listing.

FAQ

What is the best automotive adhesive?

J-B Weld Original Cold-Weld is the best overall adhesive here for metal: 5,020 PSI tensile strength and a 550-degree rating. For trim, the Loctite Ultra Gel is better, and for gaps, the SteelStik putty is better. The 3M DP100 Clear is the professional pick here, while the Gorilla epoxy is the fast-set pick for general repairs on many materials.

Is J-B Weld stronger than Gorilla Epoxy?

Yes, on metal. J-B Weld Original gives 5,020 PSI and holds to 550 degrees, while Gorilla Epoxy gives about 3,300 PSI and holds to about 180 degrees. Gorilla wins for quick general work on many materials. Gorilla epoxy also sets in five minutes and dries clear, which makes it the better pick for a visible repair that is not hot.

How long does J-B Weld take to cure?

J-B Weld Original sets in four to six hours and cures fully in 15 to 24 hours. SteelStik sets in five minutes and cures in one hour. Do not load the repair until the full cure time has passed. A bond that looks set is not yet at full strength, so leave the repair alone for the full cure time before you load it.

Can J-B Weld fix an exhaust leak?

SteelStik can seal a small exhaust leak, and owners report it holding heat shields and exhaust parts for years. For a structural exhaust repair, the Original epoxy is the stronger pick, and a cracked manifold still needs welding. SteelStik is certified for potable water contact and bonds iron, steel, copper, brass, aluminium, bronze, fibreglass, plastic and PVC.

What is the best glue for car trim?

A rubber-toughened gel like Loctite Ultra Gel Control is the best glue for trim, because it flexes when the trim moves instead of cracking. A rigid epoxy will crack off trim that flexes. The Loctite gel in this guide is rubber-toughened and flexible, so it bends with the trim instead of cracking when the trim moves.

Does epoxy work on plastic?

It depends on the plastic. J-B Weld bonds many plastics, but it will not bond polyethylene, polypropylene, Teflon or silicone rubber. Check the bond list on the listing before you buy. The 3M DP100 bonds metal, glass, ceramic and composites, so check the bond list for your material before you buy any adhesive.

How do I prepare a surface for epoxy?

Clean it, degrease it, roughen it with sandpaper and dry it completely. Oil, moisture and smooth surfaces all kill a bond, and a well-prepared surface is the difference between a repair that holds and one that lets go. The J-B Weld Original needs four to six hours to set, so clamp the parts and leave them alone until the cure time has passed.

Can I use super glue on metal?

Yes, for small, light parts. A gel like Loctite Ultra Gel bonds metal, but it is a surface bond, not a structural one. For a bracket or a load-bearing part, use a steel-reinforced epoxy instead. A gel bonds skin instantly, so wear gloves, and use only a tiny drop, since more glue makes a weaker bond.

Which automotive adhesives were excluded from this guide?

One candidate was excluded: the Permatex 84109 PermaPoxy Multi-Metal Epoxy. It is a real product, but its Amazon ASIN could not be verified in this research, so it is not picked. The Permatex 84109 has a four to five minute working time, but no Amazon ASIN was found for it in this research, so it is not picked.

Sources

By Leo, Founder, WinchInsider

Leo has researched adhesives, fasteners and garage equipment for WinchInsider since the site began, reading maker documents and owner reports so buyers can tell a real structural epoxy from a relabelled glue before they spend.

Related guides

Our top pick: J-B Weld Original Cold-Weld 8265S — 5,020 PSI, rated to 550 degrees

Check Price

Leave a Comment