A shop alignment costs money every time the suspension changes, and it changes often: new coilovers, new control arms, a track day, a kerb. The alternative is to measure the alignment yourself, and the tools for that have become good enough that a home garage can set camber, caster and toe to a tenth of a degree.
The tools fall into two kinds: gauges that measure one or two angles, and kits that measure all three. A gauge is cheaper and simpler; a kit does the whole job and pays for itself after a couple of alignments. The wrong choice is the gauge when you need toe, or the kit when you only need camber.
This guide compares four alternatives — the SPC FasTrax gauge, the Longacre digital gauge, the Tenhulzen all-in-one system and the QuickTrick portable kit — on what each one measures, how accurate it is, and what it costs to own. Three of the four are sold through their makers rather than a verified listing, and each one carries the verified gauge as its substitute buy.
The 30-second answer
For a home alignment, buy the SPC FasTrax Camber/Caster Gauge 91010 for camber and caster on a verified listing, the Longacre 78295 Digital Caster/Camber Gauge with AccuLevel for a digital readout to a tenth of a degree, the Tenhulzen 3300 DIY Alignment System for camber, caster and toe in one kit, or the QuickTrick 4th Gen DIY Wheel Alignment Kit for a portable kit that measures all three angles on any hard surface. See also our guide to Best summer tires under 200.
How we researched this guide
We profiled four alignment tools, checked the maker instruction sheets for the SPC FasTrax and the Longacre 78295, the Tenhulzen assembly instructions, the QuickTrick product pages, and owner discussion on garage forums. One pick carries a verified Amazon listing; three are written alternatives sold through their makers, with the SPC FasTrax as the substitute buy. No tool was scored on a test we did not run, and no accuracy claim goes beyond the maker documents.
Quick picks
Best Overall
SPC FasTrax Camber/Caster Gauge 91010
Hands-free bubble gauge that reads camber to four degrees either way and caster from four negative to twelve positive, fitting 17 to 22 inch wheels.
Best Digital Readout
Longacre 78295 Digital Caster/Camber Gauge with AccuLevel
Digital camber to a tenth of a degree with AccuLevel compensation for uneven ground, plus a QuickSet adapter. Sold through the maker and racing dealers.
No verified Amazon listing exists for the Longacre 78295 Digital Caster/Camber Gauge with AccuLevel; it is sold through the Longacre Racing website. The verified buy we can stand behind here is the SPC FasTrax Camber/Caster Gauge 91010:
Best All-in-One System
Tenhulzen 3300 DIY Alignment System
One kit that measures camber, caster and toe on two wheels, made in the USA, with no turn plates needed for caster. Sold through the maker and Summit Racing.
No verified Amazon listing exists for the Tenhulzen 3300 DIY Alignment System; it is sold through the Tenhulzen Automotive website. The verified buy we can stand behind here is the SPC FasTrax Camber/Caster Gauge 91010:
Best Portable Kit
QuickTrick 4th Gen DIY Wheel Alignment Kit
Portable frames and a digital gauge that measure caster, camber and toe on any hard surface, with a lifetime parts warranty. Sold through the maker.
No verified Amazon listing exists for the QuickTrick 4th Gen DIY Wheel Alignment Kit; it is sold through the QuickTrick Alignment website. The verified buy we can stand behind here is the SPC FasTrax Camber/Caster Gauge 91010:
Match an alignment tool to your car and your job
Tap your answers
Step 1 — What are you aligning?
Step 2 — What do you need to measure?
Step 3 — What matters most?
Tap the cards above to tell the finder what you are aligning and what you need to measure, and your matching tool appears here, with its buying route stated honestly.
Quick compare
| Product | Key coverage | Standout function | Updates | Form | Check Price |
|---|---|---|---|---|---|
| SPC FasTrax Camber/Caster Gauge 91010 | Camber, caster | Bubble gauge, no batteries | Not applicable | Gauge | Check Price |
| Longacre 78295 Digital Caster/Camber Gauge with AccuLevel | Camber, caster | Digital readout to 0.1 degrees | Not published | Digital gauge | No verified Amazon listing; verified substitute is the SPC FasTrax Camber/Caster Gauge 91010. Check Price |
| Tenhulzen 3300 DIY Alignment System | Camber, caster, toe | All-in-one, no turn plates | Not published | Kit | No verified Amazon listing; verified substitute is the SPC FasTrax Camber/Caster Gauge 91010. Check Price |
| QuickTrick 4th Gen DIY Wheel Alignment Kit | Camber, caster, toe | Portable, any hard surface | Not published | Kit | No verified Amazon listing; verified substitute is the SPC FasTrax Camber/Caster Gauge 91010. Check Price |
How to choose an alignment tool
Start with the angles you need
Camber alone needs a gauge. Camber, caster and toe need a kit or a gauge plus toe plates. Toe is the angle that wears tyres fastest, so a buyer who only measures camber will fix the handling and still eat tyres. See also our guide to Best tire inflator under 50.
Read the readout you can trust
A bubble gauge reads in fractions of a degree by eye, and a digital gauge reads to a tenth. The digital reading is easier to repeat, but the bubble gauge never needs a battery and never lies about a dead display. Choose the readout you will believe at the end of a long day in the garage.
Mind the floor
Every tool in this guide assumes a flat, hard surface, and the Longacre AccuLevel exists precisely because most garage floors are not level. A tenth of a degree of floor slope reads as a tenth of a degree of camber, so level the floor or buy the tool that compensates for it. Our guide to Best portable tire inflator under 100 covers the same job in more depth.
Check the wheel size and the sidewall
The FasTrax 91010 fits 17 to 22 inch wheels, the QuickTrick covers 13 to 22.5 inches by option, and the Tenhulzen fits tyre sidewalls up to about 7.5 inches. A kit that does not fit your wheels is a shelf ornament, so measure the wheels before ordering.
Count the whole job
A gauge plus toe plates can cost less than a kit, but it takes longer and needs more setup. A kit costs more up front and pays for itself after a couple of alignments. Add your time to the price before you compare. For the wider toolkit, see our guide to Best cordless tire inflators under 50.
Buy from the maker where there is no listing
Three of the four picks in this guide are sold through their makers rather than a verified listing. That is normal for specialist alignment tools, and the buying route is stated honestly under each one, with the verified gauge as the substitute buy.
Alignment tools by budget
The tiers below are about the job: one angle, two angles, or the whole alignment. No prices are listed, because the right tier is decided by the angles you need, not the wallet. Compare the options in our guide to Best heavy duty tire plug tools under 50 before you decide.
| Tier | What you get | Example pick |
|---|---|---|
| One angle | Camber measurement for a check after suspension work | SPC FasTrax 91010 |
| Two angles | Camber and caster with a digital readout | Longacre 78295 |
| Whole alignment | Camber, caster and toe in one kit, no rack | Tenhulzen 3300 or QuickTrick 4th Gen |
Types of alignment tools
Alignment tools fall into three types, and the type decides how many angles you can set and how much floor space you need. Our guide to Best mud terrain tires under 500 covers the same job in more depth.
| Type | How it works | Best for | Watch out for |
|---|---|---|---|
| Bubble gauges | Bubble vial reads the angle by eye | Simple camber and caster checks | No digital readout, no toe |
| Digital gauges | Sensor reads the angle to a tenth | Precise camber for track work | Still needs toe plates for toe |
| All-in-one kits | Frames and gauges measure all three angles | Complete home alignment | Needs floor space and setup time |
Detailed reviews
Each tool below is judged on what it measures, how it reads, what it fits, and where it is sold. Three of the four are written alternatives, and the buying route for each one is stated honestly.
Best Overall: SPC FasTrax Camber/Caster Gauge 91010
Best Overall
Why the SPC FasTrax Camber/Caster Gauge 91010 is our pick
The FasTrax 91010 is the gauge that alignment work at home is built around.
The instruction sheet from Specialty Products Company is the authority here, and it is unusually honest about the tool’s limits.
The reason it leads this guide is that it is the only pick with a verified Amazon listing, so every other pick in the guide is carried as a written alternative with this gauge as the substitute buy.
SPC FasTrax Camber/Caster Gauge 91010 key specs
- Part number 91010
- Fits wheels 17 to 22 inches in diameter
- Camber range over 4 degrees positive or negative
- Caster range 4 degrees negative to 12 degrees positive
- Hands-free bubble gauge, no batteries
- Item weight 2.7 pounds
- Dimensions 17.1 by 10.5 by 9.3 inches
- Manufacturer Specialty Products Company
- One-year warranty against defects
- Extension 910018 fits 18-inch wheels on the 13 to 18 inch model (91000)
- Recalibration available from the maker
SPC FasTrax Camber/Caster Gauge 91010: fits and best for
The FasTrax fits the home mechanic who checks alignment after suspension work, and the track-day driver who sets camber before an event.
It also fits the buyer who wants one tool that lasts.
SPC FasTrax Camber/Caster Gauge 91010 pros and watch-outs
- No batteries or software
- Reads camber and caster directly
- Hands-free mounting
- Verified Amazon listing
- Decades-long tool life if not dropped
- Bubble reading needs practice
- No digital readout
- No toe measurement on its own
- Vial block is fragile if dropped
SPC FasTrax Camber/Caster Gauge 91010: what owners report
Owner discussion on garage forums treats the FasTrax as the reference gauge: buyers describe it as the tool they reach for after a coilover install, and the recurring advice is to use a level floor and to check the gauge against a known setting before trusting a reading. The complaint pattern is not about accuracy but about the learning curve, with new users reporting that the first readings feel slow until the procedure becomes familiar.
Coverage of owner reports is thin beyond forum threads and the maker instruction sheet, and the guide states that rather than inventing owner quotes. The instruction sheet itself is the strongest evidence for how the tool reads and what it fits.
SPC FasTrax Camber/Caster Gauge 91010: who should not buy
Buyers who need a digital readout to a tenth of a degree should not buy the FasTrax.
SPC FasTrax Camber/Caster Gauge 91010: pair it with
Pair the FasTrax with toe plates for a complete home alignment.
We may earn a commission at no cost to you.
Check the gauge on a known level surface before every session. A bubble gauge that has been dropped reads wrong silently, and a wrong reading is worse than no reading. See also our guide to Best all season tires under 100.
Best Digital Readout: Longacre 78295 Digital Caster/Camber Gauge with AccuLevel
Best Digital Readout
Why the Longacre 78295 Digital Caster/Camber Gauge with AccuLevel is our pick
The Longacre 78295 is the digital answer to the bubble gauge.
The maker instructions are the evidence here, and they are practical rather than promotional.
The watch-out is the buying route.
Longacre 78295 Digital Caster/Camber Gauge with AccuLevel key specs
- Part number 78295
- Digital camber readout to 0.1 degrees
- AccuLevel compensation for uneven ground
- Caster range 4 degrees negative to 12 degrees positive
- QuickSet adapter included
- Magnetic and thread-on adapters
- Do not store above 120 degrees Fahrenheit
- Replacement vials available from the maker
- Maker Longacre Racing, Monroe, Washington
- Version 3 and version 4 instructions published
- Not published: verified Amazon listing
Longacre 78295 Digital Caster/Camber Gauge with AccuLevel: fits and best for
The Longacre fits the racer and the track-day driver who sets camber to a tenth of a degree and needs the reading to repeat.
It also fits the buyer who already owns Longacre toe plates or a camber frame.
Longacre 78295 Digital Caster/Camber Gauge with AccuLevel pros and watch-outs
- Digital readout to a tenth of a degree
- AccuLevel fixes uneven ground
- QuickSet adapter for fast mounting
- Replacement vials available
- Trusted racing brand
- No verified Amazon listing found
- Display can fail in extreme heat
- Caster still read from a vial
- No toe measurement on its own
Longacre 78295 Digital Caster/Camber Gauge with AccuLevel: what owners report
Owner reports for Longacre gauges are consistent across racing forums: buyers praise the repeatability of the digital readout and the AccuLevel compensation, and the complaint pattern is the heat warning, with owners reporting displays that went blank after a gauge was left in a hot car. The maker instructions carry the same warning, so the guide treats it as a documented limit rather than an anecdote.
Longacre 78295 Digital Caster/Camber Gauge with AccuLevel: who should not buy
Buyers who want a single purchase on a verified listing should not choose the Longacre first.
Longacre 78295 Digital Caster/Camber Gauge with AccuLevel: pair it with
Pair the Longacre with the SPC FasTrax below as the verified buy.
No verified Amazon listing exists for the Longacre 78295 Digital Caster/Camber Gauge with AccuLevel; it is sold through the Longacre Racing website.
We may earn a commission at no cost to you.
Never leave the gauge in a hot car or in direct sun. Store it flat, indoors, and check the display before every session. Our guide to Best digital tire safety gauges under 50 covers the same job in more depth.
Best All-in-One System: Tenhulzen 3300 DIY Alignment System
Best All-in-One System
Why the Tenhulzen 3300 DIY Alignment System is our pick
The Tenhulzen 3300 is the only all-in-one kit in this guide.
The fitment limit is published openly and deserves attention.
Owner discussion on garage forums is positive and specific.
Tenhulzen 3300 DIY Alignment System key specs
- Model number 3300
- Measures camber, caster and toe
- Two-wheel system, made in the USA
- No turn plates needed for caster
- Fits tyre sidewalls up to about 7.5 inches
- Camber gauge accurate to within 0.1 degrees
- Works on wheels from 12 to 22 inches
- Assembly instructions published by the maker
- Sold through the maker and Summit Racing
- Not published: verified Amazon listing
Tenhulzen 3300 DIY Alignment System: fits and best for
The Tenhulzen fits the DIYer who wants a complete alignment in the garage without a rack.
It also fits the buyer who likes mechanical tools.
Tenhulzen 3300 DIY Alignment System pros and watch-outs
- Camber, caster and toe in one kit
- No turn plates needed
- Made in the USA
- Pays for itself after a few alignments
- No electronics to fail
- No verified Amazon listing found
- Two-wheel only, not four-wheel
- Sidewall height limit of about 7.5 inches
- Assumes zero wheel runout
Tenhulzen 3300 DIY Alignment System: what owners report
Owner reports on garage forums are the strongest in this guide for a written alternative: buyers describe the kit as accurate and easy to use, with one owner reporting it paid for itself after the second alignment. The caution pattern is consistent: the system is two-wheel only, so a four-wheel car can end up with a crooked steering wheel, and the aluminium construction needs care compared with heavier shop tools.
A hands-on review of the four-wheel Tenhulzen system praises the value and the clever gauge design while noting that the flexible aluminium construction needs more finesse than a steel shop tool. The guide carries that as a watch-out rather than a fault.
Tenhulzen 3300 DIY Alignment System: who should not buy
Buyers with lifted trucks, oversized off-road tyres or commercial vehicles should not buy the 3300.
Tenhulzen 3300 DIY Alignment System: pair it with
Pair the Tenhulzen with the SPC FasTrax below as the verified buy.
No verified Amazon listing exists for the Tenhulzen 3300 DIY Alignment System; it is sold through the Tenhulzen Automotive website.
We may earn a commission at no cost to you.
Measure on a flat, hard surface and check wheel runout first. The system assumes the wheels run true, and a bent wheel reads as a bad alignment. For the wider toolkit, see our guide to Best tire pressure monitoring systems under 100.
Best Portable Kit: QuickTrick 4th Gen DIY Wheel Alignment Kit
Best Portable Kit
Why the QuickTrick 4th Gen DIY Wheel Alignment Kit is our pick
The QuickTrick 4th Gen is the portable kit in this guide.
The maker is clear that this is the final production run of the 4th Gen system, which matters for a buyer deciding whether to wait.
Owner discussion is consistent: buyers describe the kit as portable and easy to set up, and the recurring praise is for the slider system that holds the gauge in place while the wheel is adjusted.
QuickTrick 4th Gen DIY Wheel Alignment Kit key specs
- 4th Gen DIY wheel alignment kit
- Measures caster, camber and toe
- Works on any hard surface, no rack needed
- Wheel sizes 13 to 22.5 inches by option
- Made in the USA
- Lifetime parts warranty
- Final production run of the 4th Gen
- 5th Gen QuickString is the current replacement
- Frames, digital gauge, tape measures, case included
- Sold through the maker
- Not published: verified Amazon listing
QuickTrick 4th Gen DIY Wheel Alignment Kit: fits and best for
The QuickTrick fits the racer and the mobile mechanic who aligns cars at the track or in a customer’s driveway.
It also fits the home garage that cannot fit a rack.
QuickTrick 4th Gen DIY Wheel Alignment Kit pros and watch-outs
- Portable, sets up anywhere
- Measures all three angles
- Lifetime parts warranty
- Made in the USA
- Long owner history
- No verified Amazon listing found
- Final production run, replaced by 5th Gen
- First setup has a learning curve
- Dearest kit in this guide
QuickTrick 4th Gen DIY Wheel Alignment Kit: what owners report
Owner reports for QuickTrick are consistent across track and garage forums: buyers praise the portability and the slider system, and the complaint pattern is the first-setup learning curve rather than the tool itself. The maker notes that the kits are in use in over 100 countries and trusted by professional and amateur racers, which matches the forum picture.
Owner coverage for the 4th Gen is broad but general, and the guide states that rather than attributing a specific owner’s words to a specific kit variant. The maker product pages are the evidence for the specifications and the warranty.
QuickTrick 4th Gen DIY Wheel Alignment Kit: who should not buy
Buyers who want the newest system should not buy the 4th Gen.
QuickTrick 4th Gen DIY Wheel Alignment Kit: pair it with
Pair the QuickTrick with the SPC FasTrax below as the verified buy.
No verified Amazon listing exists for the QuickTrick 4th Gen DIY Wheel Alignment Kit; it is sold through the QuickTrick Alignment website.
We may earn a commission at no cost to you.
Do the first setup on a car you know, not on a car you need to drive tomorrow. The learning curve is real, and the second alignment is always faster than the first. Compare the options in our guide to Best tire safety gauges under 50 before you decide.
Spec comparison
The comparison below lines up the angles, the readout, the fitment and the buying route, so the gap between a gauge and a kit is visible at a glance.
| Spec | SPC FasTrax Camber/Caster Gauge 91010 | Longacre 78295 Digital Caster/Camber Gauge with AccuLevel | Tenhulzen 3300 DIY Alignment System |
|---|---|---|---|
| Measures | Camber, caster | Camber, caster | Camber, caster, toe |
| Readout | Bubble, by eye | Digital to 0.1 degrees | Bubble gauge |
| Wheel fit | 17 to 22 inches | Not published | 12 to 22 inches |
| Needs a rack | No | No | No |
| Warranty | One year | Not published | Not published |
| Check Price | Check Price | Written alternative; verified substitute is the SPC FasTrax Camber/Caster Gauge 91010. Check Price | Written alternative; verified substitute is the SPC FasTrax Camber/Caster Gauge 91010. Check Price |
| Spec | QuickTrick 4th Gen DIY Wheel Alignment Kit |
|---|---|
| Measures | Camber, caster, toe |
| Readout | Digital gauge |
| Wheel fit | 13 to 22.5 inches |
| Needs a rack | No |
| Warranty | Lifetime parts |
| Check Price | Written alternative; verified substitute is the SPC FasTrax Camber/Caster Gauge 91010. Check Price |
Installation and first use
Start on a flat, hard surface. A garage floor that looks level can slope enough to read as camber, so check the floor with a long level first, or use a gauge with level compensation such as the Longacre AccuLevel. Mark the floor positions for the wheels so the car returns to the same spot for every measurement. See also our guide to Best car ramps under 50.
Set the tyre pressures first, then settle the suspension by rolling the car back and forth and bouncing each corner. A car that has just come off a jack sits high, and the camber reads wrong until the suspension settles. Lock the steering wheel straight before measuring toe, and check the wheel runout if the readings jump between measurements. Our guide to Best tire pressure monitoring systems under 300 covers the same job in more depth.
Measure camber first, then caster, then toe, in that order. Camber and caster are set by the suspension adjustment, and toe is set last because it changes when the other two move. Write every reading down with the date and the mileage, because an alignment is a record, not a memory. For the wider toolkit, see our guide to Best tire monitoring systems under 200.
Check the gauge itself before every session. A bubble gauge that has been dropped reads wrong silently, and a digital gauge that has been left in a hot car may have a dead display. Verify the gauge on a known level surface, and replace a cracked vial before trusting a reading.
Safety essentials
- Never work under a car supported only by a jack: use stands.
- Never adjust alignment with the car on a slope.
- Never trust a gauge that has been dropped: check it first.
- Never drive on an alignment you have not measured twice.
- Never set toe without locking the steering wheel straight.
- Never ignore a bent part: no adjustment fixes a bent control arm.
The safety net for home alignment is a flat floor, a car on stands, and a gauge that has been checked before use. The three tools below are the ones that do the measuring. For the wider toolkit, see our guide to Best heavy duty commercial tire inflators under 200.
SPC FasTrax Camber/Caster Gauge 91010. The reference gauge: reads camber and caster with no batteries and no software, and it is the verified buy behind every written alternative in this guide.
Tenhulzen 3300 DIY Alignment System. The all-in-one kit: measures camber, caster and toe together, so no angle is left unmeasured and no tyre is left to wear unevenly.
No verified Amazon listing exists for the Tenhulzen 3300 DIY Alignment System; it is sold through the Tenhulzen Automotive website. The verified buy we can stand behind here is the SPC FasTrax Camber/Caster Gauge 91010:
QuickTrick 4th Gen DIY Wheel Alignment Kit. The portable kit: measures all three angles on any hard surface, with a lifetime parts warranty, for the alignment that happens at the track.
No verified Amazon listing exists for the QuickTrick 4th Gen DIY Wheel Alignment Kit; it is sold through the QuickTrick Alignment website. The verified buy we can stand behind here is the SPC FasTrax Camber/Caster Gauge 91010:
Troubleshooting
| Symptom | Likely cause | Fix |
|---|---|---|
| Camber reads differently each time | Floor not level, or suspension not settled | Level the floor and settle the car before measuring |
| Steering wheel crooked after alignment | Toe set without centring the wheel | Lock the wheel straight, then set toe |
| Car pulls after a home alignment | Thrust angle or a bent part | Check thrust angle and inspect the suspension |
| Gauge reads wrong after a drop | Vial block damaged | Return it to the maker for recalibration |
| Digital display blank in heat | Gauge stored above 120 degrees | Store indoors and let it cool before use |
| Kit does not fit the truck | Sidewall taller than 7.5 inches | Use a gauge and toe plates instead of the kit |
Who should NOT buy these
Buyers with bent suspension parts. No gauge or kit fixes a bent control arm, a worn ball joint or a buckled wheel. Replace the part first, then measure, or the alignment will read wrong and the car will still pull. Compare the options in our guide to Best car accessories under 200 before you decide.
Buyers who will not measure twice. A single reading is a guess. A home alignment needs a second measurement to confirm the first, and a buyer who will not take the time should pay a shop instead.
Buyers with lifted trucks and oversized tyres. The Tenhulzen kit fits sidewalls up to about 7.5 inches, and a lifted truck will not fit. Measure the sidewall before ordering any kit, and use a gauge if the kit does not fit.
Final verdict
SPC FasTrax 91010: the reference gauge, and the verified buy in this guide.
Longacre 78295: the digital readout, for the tenth of a degree that matters.
Tenhulzen 3300: the all-in-one kit, and the fastest payback in the garage.
QuickTrick 4th Gen: the portable kit, for the alignment that happens anywhere. See also our guide to Best OBD2 scanner under 100.
FAQ
Can I do a wheel alignment at home?
Yes, for camber, caster and toe, with a gauge or a kit from this guide and a flat, hard surface. A home alignment checks and adjusts the angles; it does not replace a shop alignment for a car with bent parts or a thrust-angle problem.
Which alignment tool is best for a beginner?
The SPC FasTrax 91010, because it is a bubble gauge with no electronics: mount it, read it, adjust. A digital gauge is easier to read, but the FasTrax teaches the procedure and never needs charging. It mounts on the wheel, reads camber and caster from its vials, and needs no battery, so a beginner learns the procedure instead of trusting a screen.
Do I need turn plates for a home alignment?
No, not with the kits in this guide. The Tenhulzen 3300 measures caster without turn plates, and the QuickTrick works on any hard surface. Turn plates help, but they are not required for a home check. Caster is measured by turning the wheels through a set angle, and the kits in this guide do that without plates, though plates make the job smoother.
How accurate is a DIY alignment?
A good gauge reads camber to a tenth of a degree, which is accurate enough for street and track use, provided the floor is level and the wheels run true. A bent wheel or an uneven floor reads as a bad alignment, so check both first.
What is the difference between camber, caster and toe?
Camber is the tilt of the wheel viewed from the front, caster is the tilt of the steering axis viewed from the side, and toe is whether the front of the wheels point in or out. Toe wears tyres fastest, camber affects grip, and caster affects steering feel and return.
Can I align my car with just a camber gauge?
You can set camber and caster, but not toe, and toe is the angle that eats tyres. Pair a camber gauge with toe plates, or buy an all-in-one kit such as the Tenhulzen or the QuickTrick. Toe is the angle that wears tyres fastest, so a camber-only gauge leaves the most expensive angle unset; add toe plates or choose an all-in-one kit.
Why is my steering wheel crooked after a DIY alignment?
Usually because the alignment was done on two wheels only, or the toe was set without centring the steering wheel. Lock the wheel straight before measuring toe, and check the thrust angle if the car still pulls. A car that still pulls after a careful two-wheel check usually has a thrust-angle problem, which needs a four-wheel check or a shop visit to correct.
Is the QuickTrick 4th Gen still available?
The maker lists it as the final production run, with the 5th Gen QuickString as the current replacement. The 4th Gen remains a proven kit with a lifetime parts warranty, but buyers who want the newest system should order the 5th Gen.
Do alignment tools work on trucks?
Yes, with the right size. The FasTrax 91010 fits 17 to 22 inch wheels, and the QuickTrick covers 13 to 22.5 inch wheels by option. The Tenhulzen is the exception: it fits tyre sidewalls up to about 7.5 inches, so lifted trucks may not fit.
Sources
- SPC FasTrax 91010 — Amazon listing data
- SPC FasTrax instruction sheet — part numbers 91000 and 91010
- SPC FasTrax 91010 — maker FAQ
- Longacre 78295 — maker instructions, version 3
- Longacre 78295 — maker instructions, version 4
- Tenhulzen 3300 — assembly instructions
- Tenhulzen 3300 — owner discussion
- Tenhulzen 4-wheel system — hands-on review
- QuickTrick 4th Gen — maker product page
- QuickTrick 4th Gen Elite Slider — maker product page
- Digital camber caster gauge guide — accuracy and limits
- SPC FasTrax — Summit Racing instruction sheet
By Leo, Founder, WinchInsider
Leo researches automotive tools and recovery gear from maker documents, listing evidence and owner reports — never from press releases — and publishes the exclusions alongside the picks.