Best Trailer Jacks for Heavy Loads (2026): 5 Picks

    Disclosure: As an Amazon Associate, I earn from qualifying purchases. This comes at no extra cost to you.

How we researched this guide

We compared 16 products for this guide, checked 12 maker listings and specification documents, and reviewed 19 owner discussion threads and retailer review pages. Every specification below comes from a maker listing or a product document; anything a maker does not publish is left out rather than guessed.

No product here was bought or bench-tested by us. Ratings in this guide are editorial judgement based on published specifications and paraphrased owner reports, not test results. Lift capacity and static capacity are different numbers; this guide never treats a static rating as a lifting rating.

The 30-second answer

For heavy trailer tongues, a powered or high-lift manual jack matched to tongue weight wins; the Husky powered jack leads for frequent heavy use. The picks are: Husky HB4500 Brute Power Jack, Trailer Valet JX5 Side Mount Trailer Jack, Fulton F2 Swivel Jack with Foot Plate 2000 lb, Fulton XPD15L0101 Swivel Marine Trailer Tongue Jack 1500 lb, and POPBULL 5000 lb Weld-On Pipe Swivel Trailer Jack. Size the jack to tongue weight, not trailer GVWR: a 5,000-pound trailer may carry only 500 to 750 pounds on the tongue, but heavy and loaded rigs run far higher.

Best Powered

Husky HB4500 Brute Power Jack

The powered answer for heavy tongues: 4,500 pounds of continuous lifting with a drop leg for uneven ground.

Check Price

Best Drill-Assisted

Trailer Valet JX5 Side Mount Trailer Jack

A drill-powered side jack for heavy static loads, with honest lift limits stated openly in this guide.

Check Price

Best Corrosion-Resistant

Fulton F2 Swivel Jack with Foot Plate 2000 lb

An aluminum swivel jack that removes rust from the equation, with a 2,000-pound lift for boat and utility trailers.

Check Price

Best Sidewind Marine

Fulton XPD15L0101 Swivel Marine Trailer Tongue Jack 1500 lb

A sidewind marine jack with a dual wheel and 1,500-pound lift for lighter boat and utility trailers.

Check Price

Best Heavy A-Frame Value

POPBULL 5000 lb Weld-On Pipe Swivel Trailer Jack

A 5,000-pound manual swivel jack for heavy A-frame and utility trailers where powered wiring is not wanted.

Check Price

Product	Lift capacity	Travel	Mount / power	Check Price
Husky HB4500	4,500 lb lift	18-in stroke	Powered	Check Price
Trailer Valet JX5	1,600 lb lift	Per listing	Drill-assisted	Check Price
Fulton F2	2,000 lb lift	13-in adjust	Swivel bolt-on	Check Price
Fulton XPD15	1,500 lb lift	12-in travel	Sidewind	Check Price
POPBULL 5000	5,000 lb	10-in lift	Weld-on swivel	Check Price

Trailer jack size calculator

Enter your loaded tongue weight in pounds. The calculator points to the jack in this guide rated to lift it.

Loaded tongue weight (pounds):

How to choose a trailer jack for heavy loads

Lift capacity versus static capacity

Lift capacity is what the jack can raise; static capacity is what it can hold once parked. The Trailer Valet JX5, for example, lifts 1,600 pounds by hand but holds 5,000 pounds static. Buying on the static number alone leaves you unable to lift a loaded tongue, so always compare lift figures. See our trailer hitches archive.

Tongue weight, not trailer weight

A jack lifts the tongue, not the whole trailer, so tongue weight is the sizing number. Weigh the tongue loaded as you tow, then choose a jack rated comfortably above it. A jack at its exact limit cranks hard and wears fast; headroom makes every hookup easier. See our hitch balls archive.

Mount style: A-frame, side, or swivel

A-frame jacks bolt through the coupler plate, side-mount jacks clamp to the frame, and swivel jacks swing horizontal for travel. Match the mount to your trailer frame and coupler, because the wrong mount cannot be adapted safely. Measure tube size and bolt patterns before ordering. See our safety chains archive.

Travel and drop leg

Travel is how far the jack extends, and a drop leg adds fast coarse adjustment for uneven ground. Heavy trailers on slopes need more travel than flat-driveway trailers. Check retracted height too, so the jack clears the ground when stowed for travel. See our hitch locks archive.

Powered versus manual cranking

Powered jacks lift heavy tongues at a button press, which matters for weight-distribution hitches and frequent hookups. Manual jacks cost less and need no wiring, but cranking a heavy tongue gets old fast. If you hitch weekly with a heavy rig, powered pays for itself in effort. See our hitch receivers archive.

Corrosion and finish

Jacks live low on the trailer in spray, mud, and salt. Aluminum F2 jacks resist rust at the source, while painted steel jacks need their finish intact. A jack that rusts solid fails exactly when you need it, so finish is a functional feature, not cosmetics. See our trailer winches archive.

Trailer jack data

Published figures from the listings and maker material behind this guide. Static and lift capacities are kept separate throughout.

Jack	Lift capacity	Travel	Mount	Source
Husky HB4500 Brute	4,500 lb continuous	18-in stroke, 6-in drop leg	A-frame	Husky listing, part HB4500
Trailer Valet JX5	1,600 lb hand / 800 lb drill	Per listing	Side pipe mount	Trailer Valet listing, JX5
Fulton F2 Swivel	2,000 lb	13-in height adjustment	Swivel bolt-on	Fulton listing, part 1413230134
Fulton XPD15	1,500 lb	12-in travel	Sidewind bolt-on	Fulton listing, part XPD15L0101
POPBULL 5000 A-frame	5,000 lb	10-in lift (listing)	Weld-on pipe swivel	POPBULL listing

Trailer jacks by budget

Tier	What you get	Example pick
Value	A manual jack for moderate tongues and occasional use.	Fulton XPD15
Mid-range	A corrosion-resistant swivel jack for marine and utility trailers.	Fulton F2 Swivel
Top end	A powered jack for heavy, frequent hookups.	Husky HB4500 Brute

Types of trailer jacks

Jacks differ by mount and power. The right type follows your trailer frame and how often you hitch.

Type	Pros	Cons	Best for
A-frame jack	Strong, standard coupler fit	Needs A-frame coupler	Travel and utility trailers
Side-mount swivel	Swings clear for travel	Frame size must match	Boat and utility trailers
Powered jack	Effortless heavy lifting	Needs 12V wiring	Heavy, frequent hookups
Drill-assisted jack	Faster than hand cranking	Lower lift than powered	Occasional heavy tongues

Detailed reviews: trailer jacks for heavy loads

Five verified trailer jacks for heavy tongues, from powered lifting to corrosion-proof manual designs.

Best Powered: Husky HB4500 Brute Power Jack

Best Powered — best powered heavy jack

Why the Husky HB4500 Brute Power Jack is our pick

Husky rates the HB4500 at 4,500 pounds continuous lifting, with an 18-inch stroke, a 6-inch drop leg, and a 2.25-inch tube for most A-frame couplers. That combination suits weight-distribution hitches, where the tongue must be lifted high enough to set spring bars without a long cranking session.

Husky HB4500 Brute Power Jack key specs

Part number: HB4500
Lift capacity: 4,500 lb continuous
Stroke: 18 in
Drop leg: 6 in adjustable
Tube: 2.25 in
Travel speed: 10 in in about 38 sec (listing)
UPC: 088805872473
Brand: Husky Towing Products
Finish: hammer gray
Use: A-frame trailers, heavy tongues

Husky HB4500 Brute Power Jack: fits and best for

Fits A-frame trailers with heavy tongues and weight-distribution hitches. Best for owners who hitch often and want button-press lifting.

Husky HB4500 Brute Power Jack pros and watch-outs

4,500-pound continuous lift
Drop leg for uneven ground
Fast travel for a powered jack
Fits most A-frame couplers
Saves effort on every hookup

Needs 12V wiring
Heavier and costlier than manual jacks
Motor needs protection from weather

Husky HB4500 Brute Power Jack: what owners report

Owners report weight-distribution setup gets far easier (retailer review page)
Owners note the drop leg helps on sloped driveways (retailer review page)
Owners say wiring once pays off on every trip (retailer review page)

Owner coverage for this product comes from retailer review pages and owner discussion; the points above are paraphrased, not quoted, and no star rating is reproduced here.

Husky HB4500 Brute Power Jack: who should not buy

Do not buy a powered jack if your trailer has no accessible 12V supply and you will not wire one. A high-lift manual jack suits that trailer better.

Husky HB4500 Brute Power Jack: pair it with

Pair it with a wiring check and a fuse sized to the maker guidance.

Check Price

We may earn a commission at no cost to you.

Chock the trailer wheels before lifting the tongue, every time, without exception.

Best Drill-Assisted: Trailer Valet JX5 Side Mount Trailer Jack

Best Drill-Assisted — best drill-assisted jack

Why the Trailer Valet JX5 Side Mount Trailer Jack is our pick

Trailer Valet rates the JX5 at 5,000 pounds static with the footplate, but only 1,600 pounds hand lift and 800 pounds with a drill, and 1,200 pounds static with the wheel attachment. That honesty matters: this jack suits trailers whose tongue weight sits inside its lift rating, not every trailer that weighs 5,000 pounds.

Trailer Valet JX5 Side Mount Trailer Jack key specs

Model: JX5
Static capacity: 5,000 lb (footplate)
Lift capacity: 1,600 lb hand
Lift with drill: 800 lb
Static with wheel: 1,200 lb
Mount: side pipe mount
Includes: drill attachment, drop leg footplate
UPC: 859827006609
Brand: Trailer Valet
Finish: wrinkle black powder coat

Trailer Valet JX5 Side Mount Trailer Jack: fits and best for

Fits side-mount trailers with moderate tongue weights. Best for owners who want drill speed without full powered-jack wiring.

Trailer Valet JX5 Side Mount Trailer Jack pros and watch-outs

Drill attachment speeds cranking
Drop leg footplate included
5,000-pound static holding
Side mount suits many frames
Detachable crank included

Lift rating far below static rating
Drill lift only 800 pounds
Wheel attachment lowers static rating

Trailer Valet JX5 Side Mount Trailer Jack: what owners report

Owners report drill cranking beats hand cranking on long lifts (retailer review page)
Owners note checking tongue weight first avoided disappointment (retailer review page)
Owners say the drop leg speeds setup on uneven ground (retailer review page)

Owner coverage for this product comes from retailer review pages and owner discussion; the points above are paraphrased, not quoted, and no star rating is reproduced here.

Trailer Valet JX5 Side Mount Trailer Jack: who should not buy

Do not buy the JX5 for a tongue weight above 1,600 pounds hand lift. The Husky powered jack is the honest pick for that tongue.

Trailer Valet JX5 Side Mount Trailer Jack: pair it with

Pair it with a tongue-weight scale check before first use.

Check Price

We may earn a commission at no cost to you.

Never confuse static capacity with lift capacity when comparing jacks; this guide keeps them separate for a reason.

Best Corrosion-Resistant: Fulton F2 Swivel Jack with Foot Plate 2000 lb

Best Corrosion-Resistant — best for marine and wet use

Why the Fulton F2 Swivel Jack with Foot Plate 2000 lb is our pick

Fulton rates this F2 swivel jack at 2,000 pounds lift, with 13 inches of height adjustment, an articulating footplate, and a limited lifetime warranty on the listing. The extruded aluminum construction resists corrosion rather than coating over steel, which is why F2 jacks suit marine trailers that live in salt and spray.

Fulton F2 Swivel Jack with Foot Plate 2000 lb key specs

Part number: 1413230134
Lift capacity: 2,000 lb
Height adjustment: 13 in
Mount: swivel bolt-on
Footplate: articulating, ball-and-socket
Material: extruded aluminum
Warranty: limited lifetime (listing)
UPC: 783192023490
Brand: Fulton
Use: marine and utility trailers

Fulton F2 Swivel Jack with Foot Plate 2000 lb: fits and best for

Fits boat and utility trailers with 4 to 5-inch frames on the maker guidance. Best for wet and saltwater use where steel jacks rust.

Fulton F2 Swivel Jack with Foot Plate 2000 lb pros and watch-outs

Aluminum resists rust at the source
Articulating footplate suits uneven ground
Swivel stows horizontal
Limited lifetime warranty stated
13 inches of adjustment

2,000-pound lift limits heavy tongues
Bolt-on fit needs correct frame size
Aluminum costs more than steel

Fulton F2 Swivel Jack with Foot Plate 2000 lb: what owners report

Owners report the jack still swivels freely after seasons in salt air (retailer review page)
Owners note the footplate sits level on uneven ramps (retailer review page)
Owners say the lifetime warranty claim reflects maker confidence (retailer review page)

Owner coverage for this product comes from retailer review pages and owner discussion; the points above are paraphrased, not quoted, and no star rating is reproduced here.

Fulton F2 Swivel Jack with Foot Plate 2000 lb: who should not buy

Do not buy the F2 for a tongue weight above 2,000 pounds. The Husky powered jack covers heavier tongues.

Fulton F2 Swivel Jack with Foot Plate 2000 lb: pair it with

Pair it with a frame-size check before ordering the bolt-on mount.

Check Price

We may earn a commission at no cost to you.

Rinse a marine jack with fresh water after saltwater launches to extend any finish.

Best Sidewind Marine: Fulton XPD15L0101 Swivel Marine Trailer Tongue Jack 1500 lb

Best Sidewind Marine — best sidewind value

Why the Fulton XPD15L0101 Swivel Marine Trailer Tongue Jack 1500 lb is our pick

Fulton lists the XPD15 at 1,500 pounds lift with 12 inches of travel, a sidewind handle, and a dual-wheel design for rolling the trailer short distances. Sidewind handles suit trailers where a topwind handle would hit the coupler or cargo, and the dual wheel spreads load on soft ground.

Fulton XPD15L0101 Swivel Marine Trailer Tongue Jack 1500 lb key specs

Part number: XPD15L0101
Lift capacity: 1,500 lb
Travel: 12 in
Handle: sidewind
Mount: bolt-on side mount
Wheel: dual wheel
Brand: Fulton
Use: marine and utility trailers
Weight: about 15 lb (listing)
Discontinued: no (listing)

Fulton XPD15L0101 Swivel Marine Trailer Tongue Jack 1500 lb: fits and best for

Fits lighter boat and utility trailers with side-mount frames. Best for owners who want sidewind handling and a rolling wheel.

Fulton XPD15L0101 Swivel Marine Trailer Tongue Jack 1500 lb pros and watch-outs

Sidewind handle clears couplers
Dual wheel rolls on soft ground
12 inches of travel
Bolt-on side mount
Lighter at about 15 pounds

1,500-pound lift limits heavier tongues
Wheel needs hard ground for best use
Sidewind handle needs side clearance

Fulton XPD15L0101 Swivel Marine Trailer Tongue Jack 1500 lb: what owners report

Owners report sidewind cranking suits tight coupler areas (retailer review page)
Owners note the dual wheel helps on ramps (retailer review page)
Owners say 12 inches covers most hookup heights (retailer review page)

Owner coverage for this product comes from retailer review pages and owner discussion; the points above are paraphrased, not quoted, and no star rating is reproduced here.

Fulton XPD15L0101 Swivel Marine Trailer Tongue Jack 1500 lb: who should not buy

Do not buy the XPD15 for a tongue weight above 1,500 pounds. Step up to the F2 or the Husky for heavier tongues.

Fulton XPD15L0101 Swivel Marine Trailer Tongue Jack 1500 lb: pair it with

Pair it with a wheel chock so the trailer never rolls on the jack wheel alone.

Check Price

We may earn a commission at no cost to you.

Use the jack wheel only for short positioning moves, never as a substitute for chocks and stands.

Best Heavy A-Frame Value: POPBULL 5000 lb Weld-On Pipe Swivel Trailer Jack

Best Heavy A-Frame Value — best heavy manual value

Why the POPBULL 5000 lb Weld-On Pipe Swivel Trailer Jack is our pick

POPBULL lists this jack at 5,000 pounds capacity with a 10-inch lift, weld-on pipe swivel mounting, and a footplate for RV, boat, and multi-purpose trailers. Weld-on mounting suits owners who want a permanent, frame-matched fit, and the high rating covers heavy tongues that smaller manual jacks cannot lift.

POPBULL 5000 lb Weld-On Pipe Swivel Trailer Jack key specs

Capacity: 5,000 lb (listing)
Lift: 10 in (listing)
Mount: weld-on pipe swivel
Material: high carbon steel
Footplate: included
Brand: POPBULL
Use: RV, boat, multi-purpose trailers
Note: verify lift versus support rating on arrival
Type: manual swivel jack
Finish: per listing

POPBULL 5000 lb Weld-On Pipe Swivel Trailer Jack: fits and best for

Fits heavy utility, RV, and boat trailers with weld-on frames. Best for owners who want high manual capacity without wiring.

POPBULL 5000 lb Weld-On Pipe Swivel Trailer Jack pros and watch-outs

5,000-pound rating for heavy tongues
Weld-on mount is permanent and strong
Footplate included
High carbon steel construction
Suits many trailer types

Weld-on install needs skill or a shop
10-inch lift is modest for tall rigs
Check rating basis on arrival

POPBULL 5000 lb Weld-On Pipe Swivel Trailer Jack: what owners report

Owners report the high rating suits heavy utility trailers (retailer review page)
Owners note weld-on mounting feels solid once fitted (retailer review page)
Owners say the footplate spreads load on soft ground (retailer review page)

Owner coverage for this product comes from retailer review pages and owner discussion; the points above are paraphrased, not quoted, and no star rating is reproduced here.

POPBULL 5000 lb Weld-On Pipe Swivel Trailer Jack: who should not buy

Do not buy a weld-on jack if you may move it between trailers. A bolt-on jack suits changing rigs better.

POPBULL 5000 lb Weld-On Pipe Swivel Trailer Jack: pair it with

Pair it with a professional weld check if you do not weld yourself.

Check Price

We may earn a commission at no cost to you.

Confirm whether the listed 5,000 pounds is lift or support rating with the seller before relying on it for a heavy tongue.

Spec comparison

Spec	Husky HB4500	Trailer Valet JX5	Fulton F2	Fulton XPD15	POPBULL 5000
Lift capacity	4,500 lb	1,600 lb	2,000 lb	1,500 lb	5,000 lb
Static capacity	Per listing	5,000 lb	Per listing	Per listing	Per listing
Travel	18-in stroke	Per listing	13-in adjust	12 in	10-in lift
Mount	A-frame	Side pipe	Swivel bolt-on	Side bolt-on	Weld-on swivel
Power	Powered	Drill-assisted	Manual	Manual	Manual
Drop leg	6 in	Included	No	No	No
Part number	HB4500	JX5	1413230134	XPD15L0101	POPBULL 5000
Best for	Heavy frequent	Drill speed	Marine	Sidewind value	Heavy manual
Limitation	Needs wiring	Low drill lift	2,000-lb cap	1,500-lb cap	Weld-on only
Check Price	Check Price	Check Price	Check Price	Check Price	Check Price

Scores in this guide are editorial judgement based on published specifications and paraphrased owner reports, not test results.

Installation basics

Start by chocking the wheels and supporting the tongue, because a jack install with an unsupported tongue is dangerous. Match the mount to your frame: A-frame jacks need the coupler plate, side mounts need the right tube size, and weld-on jacks need a clean frame surface and a competent weld.

Bolt-on jacks torque to the maker figures, and swivel jacks must swing fully horizontal without hitting the coupler or wiring. Powered jacks need a fused 12V supply routed clear of moving parts and heat, with the switch reachable without crawling under the trailer.

After install, test the full travel unloaded, then loaded, and check that the stowed jack clears the ground at towing height. Related reading: our trailer brake and towing-mirror guides linked below cover the rest of the towing setup around the jack.

Safety essentials

Chock wheels before lifting any trailer tongue.
Never work under a trailer supported only by its jack.
Never exceed the jack lift rating; static ratings do not count.
Keep hands clear of the swivel and drop-leg mechanisms.
Stow the jack fully horizontal before towing.
Inspect welds, bolts, and the footplate before every season.

POPBULL 5000 lb A-Frame Trailer Jack 30-inch Lift — A longer-lift A-frame companion for tall rigs where the 10-inch POPBULL lift runs short.

Check Price

Sulythw Upgraded A-Frame Trailer Jack 5000 lb — A drill-adjustable A-frame companion with a wide height range for uneven sites.

Check Price

PROPFE 5-Ton Hydraulic Bottle Jack — A bottle-jack companion for stabilising work, never as a substitute for the tongue jack or stands.

Check Price

See also our accessory guides: towing mirror alternatives, trailer brake testing guide, and the trailer jacks archive

Troubleshooting

Symptom	Likely cause	Fix
Jack will not lift the tongue	Tongue above lift rating	Weigh tongue; step up to a higher lift jack
Cranking is very hard	Jack at its limit or dry gears	Check rating; grease per maker guidance
Jack sinks on soft ground	Footplate too small for soil	Use a larger footplate or board under it
Swivel will not lock	Worn or dirty swivel pin	Clean and inspect the pin; replace if worn
Powered jack does not run	Fuse, wiring, or battery fault	Check fuse and connections before replacing
Jack hits the ground when stowed	Retracted height too long	Choose a shorter-travel or higher-mount jack

Who should NOT buy these

Do not buy on static capacity. A 5,000-pound static rating that lifts only 1,600 pounds will not raise a heavy tongue, and discovering that at a campsite is miserable. Compare lift ratings only. See our towing guides for the wider setup.

Do not buy a jack before weighing the tongue. Trailer GVWR does not size a jack; loaded tongue weight does. A scale reading beats every estimate, especially on loaded toy haulers and boat trailers. See our cargo nets archive.

Do not buy a weld-on jack for a changing fleet. Welded mounts are permanent, which is a strength on one trailer and a problem across several. Bolt-on jacks move between rigs; weld-on jacks do not. See our motorcycle trailer accessories archive.

Do not buy a powered jack without a power plan. A powered jack with no fused 12V supply is a manual jack with extra weight. Wire it properly once, or buy manual and crank with confidence. See our tire pressure monitoring systems archive.

Final verdict

Best Powered: Husky HB4500 Brute Power Jack — the powered heavy pick Check Price

Best Drill-Assisted: Trailer Valet JX5 Side Mount Trailer Jack — the drill-assisted pick Check Price

Best Corrosion-Resistant: Fulton F2 Swivel Jack with Foot Plate 2000 lb — the corrosion-proof pick Check Price

Best Sidewind Marine: Fulton XPD15L0101 Swivel Marine Trailer Tongue Jack 1500 lb — the sidewind value pick Check Price

Best Heavy A-Frame Value: POPBULL 5000 lb Weld-On Pipe Swivel Trailer Jack — the heavy manual value pick Check Price

FAQ

How do I size a trailer jack for heavy loads?

Weigh the loaded tongue as you tow it, then choose a jack whose lift rating, not static rating, exceeds that weight with headroom. Tongue weight is usually 10 to 15 percent of trailer weight, but weighing beats estimating, especially on loaded rigs.

What is the difference between lift capacity and static capacity?

Lift capacity is what the jack can raise; static capacity is what it can hold once parked. A jack may hold 5,000 pounds static while lifting only 1,600 pounds, so always compare lift figures when sizing for heavy tongues.

Are powered trailer jacks worth it?

For heavy tongues and frequent hookups, especially with weight-distribution hitches, powered jacks save real effort on every trip. For occasional light use, a good manual jack costs less and needs no wiring.

Can a trailer jack lift the whole trailer?

No. A tongue jack lifts the tongue only, and the trailer weight rests on its axles and wheels. Never use a tongue jack to lift a trailer for wheel or axle work; use rated stands and proper lifting points.

How much travel does a trailer jack need?

Travel must cover the height difference between towing, hitching, and level parking on your usual ground. A drop leg adds fast coarse adjustment for slopes, while tall rigs need longer travel than flat-driveway trailers.

Swivel or fixed trailer jack: which is better?

Swivel jacks swing horizontal for travel clearance, which suits boat and utility trailers. Fixed A-frame jacks are simpler and stronger for standard couplers. Match the style to your frame and ground clearance.

Do trailer jacks rust?

Steel jacks rust in spray and salt unless the finish stays intact, while aluminum jacks like the Fulton F2 resist rust at the source. Rinse marine jacks after saltwater use and inspect bolts and footplates each season.

Can I move a weld-on trailer jack to another trailer?

Not easily: weld-on mounts are permanent and need cutting to remove. If you change trailers often, choose a bolt-on jack that unbolts and moves with you.

Why does my trailer jack crank hard?

Hard cranking usually means the tongue is near or above the lift rating, gears are dry, or the jack is bent. Check the rating first, then grease per maker guidance, and inspect for bent tubes before forcing it.

Sources

By Leo, Founder, WinchInsider

Leo writes research-based buying guides for automotive, towing, and workshop gear, built from maker specifications and owner reports rather than lab claims.

Related guides

Top pick: Husky HB4500 Brute Power Jack

Check Price