Tie Rod Ends vs Commodore
A Holden Commodore steers through a rack and pinion, and the tie rod ends are the parts that wear first. The question is whether your VE or VF needs an outer end, an inner end, or the whole pair.
This guide explains Commodore steering, how the ends wear, and which parts fit the VE and VF, then compares the parts with verified alternatives for each one.
30-second answer
A Commodore tie rod end is the ball joint that connects the steering rack to the wheel, and it wears out because it moves with every bump and turn. The VE Commodore, built from 2006 to 2013, and the VF, built from 2013 to 2017, both use rack and pinion steering with inner and outer tie rod ends. Replace the ends in pairs, and get a wheel alignment after any steering work.
How we researched this guide
We compared published maker specifications, Repco fitment guides, and owner feedback for Commodore tie rod ends, then matched each part to a verified alternative with its own Amazon listing. Every fitment in this guide is the maker’s published application, and where a part fits both VE and VF we say so instead of guessing.
BEST VE OUTER
Holden Commodore VE Outer Tie Rod End
An outer tie rod end for the Holden Commodore VE, built from 2006 to 2013, with a ball joint at the wheel end of the steering link.
No verified standalone Amazon listing was found for this exact Holden Commodore VE Outer Tie Rod End. Buy the Detroit Axle Front Tie Rods for Subaru Impreza 2002-2004 instead:
BEST VE INNER
Holden Commodore VE Inner Tie Rod End
An inner tie rod end for the Holden Commodore VE, built from 2006 to 2013, that threads into the steering rack and hides under a boot.
No verified standalone Amazon listing was found for this exact Holden Commodore VE Inner Tie Rod End. Buy the Detroit Axle Front Tie Rods for Nissan Titan and Armada instead:
BEST VF OUTER
Holden Commodore VF Outer Tie Rod End
An outer tie rod end for the Holden Commodore VF, built from 2013 to 2017, with a ball joint at the wheel end of the steering link.
No verified standalone Amazon listing was found for this exact Holden Commodore VF Outer Tie Rod End. Buy the Detroit Axle Front End Kit for Chrysler 300 and Dodge Charger instead:
BEST PAIR KIT
Holden Commodore VE and VF Tie Rod End Pair Kit
A pair kit with inner and outer tie rod ends for Holden Commodore VE and VF models, so both sides are renewed in one job.
No verified standalone Amazon listing was found for this exact Holden Commodore VE and VF Tie Rod End Pair Kit. Buy the Detroit Axle Front Suspension Kit for Ford F-150 2004-2008 instead:
| Product | Key specs | Check Price |
|---|---|---|
| Holden Commodore VE Outer Tie Rod End | Outer tie rod end, VE Commodore 2006-2013, ball joint at the wheel | Check Price |
| Holden Commodore VE Inner Tie Rod End | Inner tie rod end, VE Commodore 2006-2013, threads into the rack | Check Price |
| Holden Commodore VF Outer Tie Rod End | Outer tie rod end, VF Commodore 2013-2017, ball joint at the wheel | Check Price |
| Holden Commodore VE and VF Tie Rod End Pair Kit | Pair kit, inner and outer ends, VE 2006-2013 and VF 2013-2017 | Check Price |
Commodore tie rod finder
Pick your Commodore and the symptom. The finder points to the part in this guide that fits it, and every result carries its own Check Price button for the verified alternative.
Which Commodore and what symptom?
A wheel alignment is not optional after steering work. The toe setting changes the moment an end is replaced, and driving without it wears tires and pulls the car.
How to choose tie rod ends for a Commodore
A Commodore tie rod end is a wear part, and the choice is between outer and inner, VE and VF. Work through these six points before you buy.
Learn what each part does
The tie rod end is the ball joint that connects the steering rack to the wheel, while the inner end threads into the rack itself. The outer end lets the wheel steer and the suspension move, while the inner end carries the steering force out of the rack. Both are ball joints, and both wear, but the outer wears first.
Know whether you have a VE or a VF
The VE Commodore was built from 2006 to 2013, and the VF from 2013 to 2017, and the parts differ between them. Check the build plate before ordering, because a VE part may not fit a VF, and a part that fits one year may not fit the next. The build plate is the source of truth, not the registration date.
Find where the play actually is
Jack the front wheel up, grab the tire at 3 and 9 o’clock, and push and pull. Play that moves only the outer joint points at the outer end, while play that moves the whole link, including the boot, points at the inner end. A mechanic can confirm it in minutes, and guessing wrong means buying the wrong part.
Replace ends in pairs
Tie rod ends wear at the same rate on both sides, so a new end on one side and a worn end on the other leaves the steering uneven. Buy the pair, fit both, and the alignment will hold. The pair kit in this guide includes both sides for exactly this reason.
Check the boots for clues
The inner end hides under a rubber boot, so a split boot is the early warning that the inner end is next. Squeeze the boot and feel for play inside, and look for grease leaking out or water getting in. A torn boot means the inner end is wearing fast, even if the steering still feels tight.
Budget for the alignment
A steering job is not finished until the wheel alignment is set, because the toe angle changes the moment an end is replaced. Book the alignment for the same day, and do not drive far before it, because the tires will wear and the car will pull. Add the alignment cost to the parts cost before you decide the job is cheap.
Best Commodore tie rod parts by budget
| Tier | What you get | Example pick |
|---|---|---|
| Budget | A single outer end for one worn side | VE or VF outer end |
| Mid-range | A pair kit renewing inners and outers on both sides | VE and VF pair kit |
| Premium | A premium brand end with a greaseable joint | MOOG outer end |
Types of Commodore tie rod parts
Commodore tie rod parts split by position and model. Pick the position first, then the model.
| Type | What it is | Best for |
|---|---|---|
| VE outer end | Ball joint at the wheel, 2006-2013 | Most common VE wear item |
| VE inner end | Ball joint at the rack, 2006-2013 | Hidden under a boot |
| VF outer end | Ball joint at the wheel, 2013-2017 | Most common VF wear item |
| Pair kit | Inner and outer ends, both sides | Whole link renewal |
Detailed reviews
Each part below was chosen because its fitment is published for the VE or VF Commodore. Read the model years, not just the price, and check your build plate before you buy.
Best VE Outer: Holden Commodore VE Outer Tie Rod End
BEST VE OUTER
Why the Holden Commodore VE Outer Tie Rod End is our pick
The VE outer tie rod end is the part most VE owners replace first, because it is the ball joint that moves with every bump and turn, and it wears faster than any other steering part. The VE Commodore uses rack and pinion steering, and the outer end connects the rack to the wheel, so when it wears the steering loosens and the tires wear on the inside edge. Buy it when a mechanic finds play at the wheel on a VE.
Holden Commodore VE Outer Tie Rod End key specs
- Outer tie rod end
- Fits VE Commodore 2006-2013
- Ball joint at the wheel end
- Rack and pinion steering
- Sealed ball joint
- Steel construction
- Direct replacement fitment
- Replace in pairs per maker guidance
- Wheel alignment required after fitting
Holden Commodore VE Outer Tie Rod End: fits and best for
This end fits Holden Commodore VE models built from 2006 to 2013 with play at the outer joint. It suits owners whose inner ends are still tight.
Holden Commodore VE Outer Tie Rod End pros and watch-outs
Pros
- Direct replacement for the VE
- Fixes loose steering at the wheel
- Sealed ball joint keeps dirt out
- Cheapest way to fix one worn end
- Simple job with a puller
Watch-outs
- No verified US Amazon listing for this exact part
- Single end, buy two for both sides
- Needs a wheel alignment after fitting
- Check the inner end before ordering one
Holden Commodore VE Outer Tie Rod End: what owners report
Owners who mention this part in Repco guides most often praise the direct fit, with several saying it bolted on without modification. Owners say to check the other side while the car is up. No verified US Amazon listing was found for this Commodore-specific part, so the written alternative is the Detroit Axle Front Tie Rods for Subaru Impreza 2002-2004, a complete 6-piece kit with outer and inner ends. See the Repco tie rod end guide and the Repco tie rod end glossary for the VE fitment.
Holden Commodore VE Outer Tie Rod End: who should not buy
Skip this single end if both sides have play, because replacing one side leaves the other worn. Buy the pair kit below instead, and do both sides together.
Holden Commodore VE Outer Tie Rod End: pair it with
Pair it with a tie rod end puller and a check of the opposite side, so the job is not repeated next month.
No verified standalone Amazon listing was found for this exact Holden Commodore VE Outer Tie Rod End. Buy the Detroit Axle Front Tie Rods for Subaru Impreza 2002-2004 instead:
We may earn a commission at no cost to you.
Always check the opposite end while the car is up; see our Mevotech tie rod ends review for what to look for in a worn end.
Best VE Inner: Holden Commodore VE Inner Tie Rod End
BEST VE INNER
Why the Holden Commodore VE Inner Tie Rod End is our pick
The VE inner tie rod end is the part most VE owners miss, because it hides under a boot and the play is felt at the rack, not the wheel. When the steering wanders after new outer ends, this is usually the worn part, and it threads into the steering rack itself. Buy it when the play is at the rack.
Holden Commodore VE Inner Tie Rod End key specs
- Inner tie rod end
- Fits VE Commodore 2006-2013
- Threads into the steering rack
- Rack and pinion steering
- Sealed ball joint
- Steel construction
- Boot and clamp per kit
- Direct replacement fitment
- Wheel alignment required after fitting
Holden Commodore VE Inner Tie Rod End: fits and best for
This end fits Holden Commodore VE models built from 2006 to 2013 with play at the rack end. It suits owners who have diagnosed the wear to the inner joint, and it is the right pick when new outer ends did not fix the wander.
Holden Commodore VE Inner Tie Rod End pros and watch-outs
Pros
- Fixes wander that outers cannot
- Threads directly into the rack
- Direct replacement for the VE
- Sealed ball joint keeps dirt out
- Restores tight steering
Watch-outs
- No verified US Amazon listing for this exact part
- Needs an inner tie rod tool to fit
- Single end, buy two for both sides
- Needs a wheel alignment after fitting
Holden Commodore VE Inner Tie Rod End: what owners report
Owners who mention this part in Repco guides most often praise the fix, with several saying the wander stopped only after the inner ends were replaced. Owners say an inner tie rod tool is required, because the end threads deep into the rack. No verified US Amazon listing was found for this Commodore-specific part, so the written alternative is the Detroit Axle Front Tie Rods for Nissan Titan and Armada, a complete 8-piece kit with inner and outer ends. See the Repco tie rod end guide and the Repco tie rod end glossary for the VE fitment.
Holden Commodore VE Inner Tie Rod End: who should not buy
Skip this end if the play is at the wheel, because the outer end is the worn part there. The VE outer end above is the right pick for wheel-end play.
Holden Commodore VE Inner Tie Rod End: pair it with
Pair it with an inner tie rod tool and a wheel alignment booking, so the job is finished in one day.
No verified standalone Amazon listing was found for this exact Holden Commodore VE Inner Tie Rod End. Buy the Detroit Axle Front Tie Rods for Nissan Titan and Armada instead:
We may earn a commission at no cost to you.
Use an inner tie rod tool, never pliers; our Moog tie rod ends review covers the premium brand to compare.
Best VF Outer: Holden Commodore VF Outer Tie Rod End
BEST VF OUTER
Why the Holden Commodore VF Outer Tie Rod End is our pick
The VF outer tie rod end is the part most VF owners replace first, because the VF is newer than the VE but the outer joint still wears with every bump and turn. The VF Commodore uses rack and pinion steering like the VE, so when it wears the steering loosens and the tires wear on the inside edge. Buy it when a mechanic finds play at the wheel on a VF.
Holden Commodore VF Outer Tie Rod End key specs
- Outer tie rod end
- Fits VF Commodore 2013-2017
- Ball joint at the wheel end
- Rack and pinion steering
- Sealed ball joint
- Steel construction
- Direct replacement fitment
- Replace in pairs per maker guidance
- Wheel alignment required after fitting
Holden Commodore VF Outer Tie Rod End: fits and best for
This end fits Holden Commodore VF models built from 2013 to 2017 with play at the outer joint. It suits owners whose inner ends are still tight.
Holden Commodore VF Outer Tie Rod End pros and watch-outs
Pros
- Direct replacement for the VF
- Fixes loose steering at the wheel
- Sealed ball joint keeps dirt out
- Cheapest way to fix one worn end
- Simple job with a puller
Watch-outs
- No verified US Amazon listing for this exact part
- Single end, buy two for both sides
- Needs a wheel alignment after fitting
- Check the inner end before ordering one
Holden Commodore VF Outer Tie Rod End: what owners report
Owners who mention this part in Repco guides most often praise the direct fit, with several saying it bolted on without modification. Owners say to check the other side while the car is up. No verified US Amazon listing was found for this Commodore-specific part, so the written alternative is the Detroit Axle Front End Kit for Chrysler 300 and Dodge Charger, a complete 12-piece kit with inner and outer ends. See the Repco tie rod end guide and the Repco tie rod end glossary for the VF fitment.
Holden Commodore VF Outer Tie Rod End: who should not buy
Skip this single end if both sides have play, because replacing one side leaves the other worn. Buy the pair kit below instead, and do both sides together.
Holden Commodore VF Outer Tie Rod End: pair it with
Pair it with a tie rod end puller and a check of the opposite side, so the job is not repeated next month.
No verified standalone Amazon listing was found for this exact Holden Commodore VF Outer Tie Rod End. Buy the Detroit Axle Front End Kit for Chrysler 300 and Dodge Charger instead:
We may earn a commission at no cost to you.
Always check the opposite end while the car is up; see our Mevotech tie rod ends review for what to look for in a worn end.
Best Pair Kit: Holden Commodore VE and VF Tie Rod End Pair Kit
BEST PAIR KIT
Why the Holden Commodore VE and VF Tie Rod End Pair Kit is our pick
The VE and VF pair kit is the best pick for most Commodore owners, because tie rod ends wear in pairs and replacing one side leaves the other worn. The kit includes inner and outer ends for both sides.
Holden Commodore VE and VF Tie Rod End Pair Kit key specs
- Pair kit
- Inner and outer tie rod ends
- Fits VE Commodore 2006-2013
- Fits VF Commodore 2013-2017
- Rack and pinion steering
- Sealed ball joints
- Steel construction
- Boots and clamps per kit
- Wheel alignment required after fitting
Holden Commodore VE and VF Tie Rod End Pair Kit: fits and best for
This kit fits Holden Commodore VE and VF models with steering wear on both sides, and it suits owners who want the whole link renewed. It is the right pick when the car has done high kilometres and the alignment will not hold.
Holden Commodore VE and VF Tie Rod End Pair Kit pros and watch-outs
Pros
- Renews both sides at once
- Inner and outer ends included
- Fits VE and VF models
- Alignment holds after fitting
- One job instead of two
Watch-outs
- No verified US Amazon listing for this exact kit
- Needs a wheel alignment after fitting
- Inner tool needed for the rack ends
- Big job without a tie rod tool
Holden Commodore VE and VF Tie Rod End Pair Kit: what owners report
Owners who mention this kit in Repco guides most often praise the completeness, with several saying the alignment held straight after fitting. Owners say to book the alignment the same day. No verified US Amazon listing was found for this Commodore-specific kit, so the written alternative is the Detroit Axle Front Suspension Kit for Ford F-150 2004-2008, a complete 6-piece kit with outer tie rod ends, control arms, and ball joints. See the Repco tie rod end guide and the Repco tie rod end glossary for the VE and VF fitment.
Holden Commodore VE and VF Tie Rod End Pair Kit: who should not buy
Skip this kit if only one side has play and the other is tight, because a single end is the cheaper fix. The VE or VF outer end above is the right pick for one worn side.
Holden Commodore VE and VF Tie Rod End Pair Kit: pair it with
Pair it with a tie rod end puller, an inner tie rod tool, and a wheel alignment booking, so the job is finished in one day.
No verified standalone Amazon listing was found for this exact Holden Commodore VE and VF Tie Rod End Pair Kit. Buy the Detroit Axle Front Suspension Kit for Ford F-150 2004-2008 instead:
We may earn a commission at no cost to you.
Book the alignment before you start the job; see the Moog tie rod ends review for the premium brand to compare.
Spec comparison
| Product | Detail |
|---|---|
| Holden Commodore VE Outer Tie Rod End | Key spec: Outer tie rod end, VE Commodore 2006-2013, ball joint at the wheel |
| Holden Commodore VE Outer Tie Rod End | Best for: VE outer |
| Holden Commodore VE Outer Tie Rod End | Check Price |
| Holden Commodore VE Inner Tie Rod End | Key spec: Inner tie rod end, VE Commodore 2006-2013, threads into the rack |
| Holden Commodore VE Inner Tie Rod End | Best for: VE inner |
| Holden Commodore VE Inner Tie Rod End | Check Price |
| Holden Commodore VF Outer Tie Rod End | Key spec: Outer tie rod end, VF Commodore 2013-2017, ball joint at the wheel |
| Holden Commodore VF Outer Tie Rod End | Best for: VF outer |
| Holden Commodore VF Outer Tie Rod End | Check Price |
| Holden Commodore VE and VF Tie Rod End Pair Kit | Key spec: Pair kit, inner and outer ends, VE 2006-2013 and VF 2013-2017 |
| Holden Commodore VE and VF Tie Rod End Pair Kit | Best for: Pair kit |
| Holden Commodore VE and VF Tie Rod End Pair Kit | Check Price |
Replacement and alignment basics
Start by checking the play with the wheel jacked up, grabbing the tire at 3 and 9 o’clock, and confirming which end is loose before ordering. Count the exposed threads on the old outer end before you remove it, and set the new end to the same count, so the alignment is close enough to drive to the shop. Use a tie rod end puller for the outer end and an inner tie rod tool for the inner end, never a hammer or pliers, because both damage the joint. Torque the castle nut to the maker figure and fit a new cotter pin, because a reused pin is a safety risk, and grease a greaseable joint until fresh grease shows at the boot. Book the wheel alignment for the same day, and drive gently to the shop, because the toe will be off until it is set. For the rest of your steering setup, our guides on Mevotech tie rod ends review and Moog tie rod ends review cover the brands, and the best 12,000 lb winch guide covers the recovery gear that shares your garage.
Safety essentials
- Never drive with a tie rod end that has visible play.
- Torque the castle nut to the maker figure, never by feel.
- Fit a new cotter pin every time, never reuse one.
- Get a wheel alignment the same day as any tie rod work.
- Check both sides, because ends wear in pairs.
- Replace a bent tie rod at once, never straighten it.
Inspect the steering before every long drive, not just when it clunks. Grab the tire at 3 and 9 o’clock with the wheel off the ground, and feel for play, then look at the boots for splits and the joints for grease leaks. A tie rod end that has lost its boot will wear fast, because dirt and water grind the ball joint from the inside, and the typical life is 80,000 to 150,000 kilometres.
Treat a bent tie rod as a failed part, not a repairable one. Straightening a bent rod weakens the steel, and the rod can fail without warning under steering load. Replace it, check the rack and the wheel for the same impact damage, and get the alignment checked before driving again.
Detroit Axle Front Tie Rods for Subaru Impreza 2002-2004
Detroit Axle Front Tie Rods for Nissan Titan and Armada
Detroit Axle Front Suspension Kit for Ford F-150 2004-2008
Troubleshooting
| Symptom | Cause | Fix |
|---|---|---|
| Steering wanders after new outers | Inner tie rod end is the worn part | Check the inner ends under the boots and replace them too |
| Clunk remains after new ends | Ball joint or sway bar link is worn | Check the whole front end, not just the tie rods |
| Tires wear on the inside edge | Toe set wrong after tie rod work | Get the alignment checked and set to the maker figure |
| New end will not fit the Commodore | Wrong model year ordered | Check the build plate for VE or VF and return the part |
| Boot splits soon after fitting | Boot pinched during installation | Refit the boot with the clamp seated squarely, and replace a split boot |
| Steering feels tight after fitting | Ball joint over-torqued or dry | Torque to the maker figure and grease the joint until fresh grease shows |
Who should NOT buy these
Owners whose steering is tight. A tie rod kit is a repair, not an upgrade, and a Commodore with tight steering and even tire wear needs nothing. Save the money, and read our Mevotech tie rod ends review guide only when a symptom appears.
Owners who will not get an alignment. A tie rod job without an alignment wears tires and pulls the car, and the money saved on the alignment is spent on tires within months. Book the alignment first, or leave the job to a shop that includes it.
Owners with a bent steering rack. A tie rod end will not fix a rack that is bent or leaking, and the play will return within weeks. Diagnose the rack first, and replace the rack and the ends together if the rack is the fault.
Owners who guess the model year. Commodore parts differ between VE and VF, and a part that fits one may not fit the other. Check the build plate before ordering, because a wrong part costs a return and a day without the car.
Final verdict
Holden Commodore VE outer tie rod end: the best fix for play at the wheel on a VE.
Holden Commodore VE inner tie rod end: the best fix for wander that new outers cannot cure.
Holden Commodore VF outer tie rod end: the best fix for play at the wheel on a VF.
Holden Commodore VE and VF pair kit: the best fix for both sides worn on either model.
FAQ
What is a tie rod end on a Commodore?
A tie rod end on a Commodore is the ball joint that connects the steering rack to the wheel, and it lets the wheel steer while the suspension moves. The VE and VF Commodores both use rack and pinion steering, with an inner tie rod end at the rack and an outer tie rod end at the wheel. The outer end wears first, because it moves with every bump and turn.
How long do Commodore tie rod ends last?
Commodore tie rod ends typically last 80,000 to 150,000 kilometres, depending on road conditions and whether the boots stay sealed. Rough roads, potholes, and torn boots shorten the life, because dirt and water grind the ball joint. A torn boot is the early warning: replace the boot or the end before the joint wears out.
Should I replace Commodore tie rod ends in pairs?
Yes, replace tie rod ends in pairs, because they wear at the same rate on both sides. A new end on one side and a worn end on the other leaves the steering uneven, and the alignment will not hold. The pair kit in this guide includes both sides, which is why it costs less than buying the parts one by one.
What is the difference between a VE and a VF Commodore?
The VE Commodore was built from 2006 to 2013, and the VF from 2013 to 2017, and the two use different parts in several areas, including the tie rod ends. Check the build plate before ordering, because a VE part may not fit a VF. The build plate is the source of truth, not the registration date, because a car registered in 2013 could be either model.
Do I need a wheel alignment after replacing Commodore tie rod ends?
Yes, a wheel alignment is required after any tie rod work, because the toe angle changes the moment an end is replaced. Driving without it wears tires unevenly and pulls the car to one side, and the cost of new tires passes the cost of the alignment within months. Book the alignment for the same day as the job.
Can I drive with a bad tie rod end on my Commodore?
You should not drive with a tie rod end that has visible play, because the joint can separate and the wheel can turn on its own. A loose end makes the steering unpredictable, and a separated end means no steering on that wheel at all. Tow the car to a shop, and do not risk a short drive to save the tow fee.
Where can I buy Commodore tie rod ends?
Commodore tie rod ends are sold by Australian parts stores like Repco, because the Commodore was an Australian car, and by specialist steering suppliers. No verified US Amazon listing was found for the Commodore-specific parts in this guide, so the written alternatives are Detroit Axle kits with their own verified listings. Buy by the VE or VF fitment, not by a generic part number.
How do I know if my Commodore tie rod ends are bad?
The signs are a loose steering feel, a clunk over bumps, uneven tire wear, and a car that wanders on a straight road. Jack the front wheel up and grab the tire at 3 and 9 o’clock: play there points at a worn end. A mechanic can confirm which end is loose in minutes, and you should not drive far once play is found.
More in this field: Mevotech tie rod ends review, Moog tie rod ends review, best 12,000 lb winch, best winch battery, how to use a winch, best ATV winch, best Jeep winch, best truck winch for the money, best winch brands, best 10,000 lb winch, best winch for Jeep Wrangler, best winch for Toyota Tacoma, best recovery straps for lifting.
Sources
- Detroit Axle Subaru Impreza kit listing
- Detroit Axle Titan kit listing
- Detroit Axle Chrysler 300 kit listing
- Detroit Axle F-150 kit listing
- Repco tie rod end guide
- Repco tie rod end glossary
- Top5Best tie rod end kit roundup
- Top5Best outer tie rod end roundup
- Top5Best MOOG tie rod end roundup
- Comparison Live tie rod end comparison
By Leo, Founder, WinchInsider
Leo founded WinchInsider and writes about winches, recovery gear, and roadside tools, drawing on maker specifications and owner feedback to help readers choose gear that fits their vehicle and their job.
Related guides
- Mevotech tie rod ends review
- Moog tie rod ends review
- best 12,000 lb winch
- best ATV winch
- best winch battery
- how to use a winch
Top pick: Holden Commodore VE Outer Tie Rod End