The 30-second answer
The best 6-inch polishing pads for most detailers are a graded foam set that takes you from cutting to finishing without changing backing plates, because paint correction is a sequence, not a single pad. Our picks are the SPTA HD 5-piece set, the SPTA 5-piece standard set, the SPTA 6.5-inch face mix set, the Chemical Guys yellow heavy-cutting pad, and the SPTA microfiber 2-piece set. Match the pad face to your 6-inch backing plate, start with the least aggressive pad that does the job, and keep pads clean, because a dirty pad cuts unevenly however good its foam is.
How we researched this guide
We compared 5 polishing pad products against 5 maker or retailer specification pages, checked pad diameters, foam grades, backing types and stated cutting roles where the listing published them, and reviewed 3 owner-report pages. Pad colour meanings differ by maker, so every colour claim here is tied to its own maker.
We did not test any product. Maker ratings are reported as maker ratings, owner points are paraphrased from linked owner sources, and any figure a source did not publish is printed as Not published rather than estimated.
Top Pick
SPTA HD 5-Piece Buffing Polishing Pads 6-Inch
The best graded set here: five 6-inch pads from heavy cut to finishing wax, with hook-and-loop backing, for a full correction sequence.
Best Standard Set
SPTA 5-Piece Standard Buffing Polishing Pads 6-Inch
A 5-piece 6-inch set with T-grade foam from heavy to finishing, for detailers who want graded foam at a standard tier.
Best Plate Safety Margin
SPTA 5-Piece 6.5-Inch Face Mix Pads for 6-Inch Plates
A 6.5-inch face set on a 6-inch back, for detailers who want the plate-edge safety margin on every panel, including curves.
Best Single Heavy-Cut Pad
Chemical Guys Hex-Logic Quantum Yellow Heavy-Cutting Pad 6.5-Inch
A single 6.5-inch heavy-cutting pad with Hex-Logic grooves, for severe swirls, scratches, oxidation and water spots on a 6-inch plate.
Best Microfiber
SPTA Microfiber Polishing Pads 6-Inch 2-Piece
A 2-piece 6-inch microfiber cutting and finishing set, for hard clear coats where foam cutting is too slow.
| Product | Cut and use | Check Price |
|---|---|---|
| SPTA HD 5-Piece Buffing Polishing Pads 6-Inch | Graded foam, 5 grades | Check Price |
| SPTA 5-Piece Standard Buffing Polishing Pads 6-Inch | Graded foam, T-grades | Check Price |
| SPTA 5-Piece 6.5-Inch Face Mix Pads for 6-Inch Plates | 6.5-inch face, mix grades | Check Price |
| Chemical Guys Hex-Logic Quantum Yellow Heavy-Cutting Pad 6.5-Inch | Heavy cut, Hex-Logic | Check Price |
| SPTA Microfiber Polishing Pads 6-Inch 2-Piece | Microfiber, cut and finish | Check Price |
Find your pad by backing plate size
Enter your backing plate size in inches, usually 5 or 6. This tool only compares the five picks in this guide; it does not approve a fit. Always check that the pad face is wider than the plate so the plate cannot touch paint.
Enter a number to see a pick.
How to choose 6-inch polishing pads
Face wider than the plate
The pad face must be wider than the backing plate, so the plate edge cannot strike paint. A 6.5-inch face on a 6-inch plate is the standard safety margin, and a pad the same size as the plate is a scratch risk on curved panels.
Cut grade in sequence
Correction runs from heavy cut to medium cut to polish to finish, with one pad grade per stage. Buying only a heavy-cut pad leaves holograms and haze, and buying only a finishing pad cannot remove swirls. A graded set is cheaper than buying grades one by one.
Foam versus microfiber
Foam pads cut smoothly and finish cleanly, while microfiber pads cut faster on hard clear coats but need more care to avoid haze. Most detailers start with foam and add microfiber only where foam cutting is too slow.
Hook-and-loop backing that holds
A pad that flies off at speed is dangerous and wasteful. The listings here describe hook-and-loop backings with strong adhesion, but a worn backing plate or a dirty pad back still lets go, so inspect both before each session.
Colour codes differ by maker
Yellow means heavy cut at Chemical Guys but medium cut at SPTA, so never carry a colour meaning across brands. Read the grade printed for the pad you bought, not the colour you remember from another maker.
Pad cleaning and rotation
A loaded pad cuts unevenly and overheats. Clean pads during the job, rotate through several pads per stage on a full correction, and retire pads whose foam has collapsed or whose backing has torn.
Polishing pads by budget
| Tier | What you get | Example pick |
|---|---|---|
| Lower spend | Single-grade pad or small set | Chemical Guys yellow heavy-cutting pad |
| Mid spend | Graded 5-piece foam set | SPTA HD 5-piece set |
| Higher spend | Foam set plus microfiber set | SPTA microfiber 2-piece set |
Types of polishing pads
| Type | Pros | Cons | Best for |
|---|---|---|---|
| Foam cutting pad | Removes swirls and oxidation | Can leave haze if too aggressive | Correction stages |
| Foam polishing pad | Refines after cutting | Cannot remove deep defects | Mid-stage refinement |
| Foam finishing pad | Final gloss, wax and glaze | No cut at all | Final stage and waxing |
| Microfiber pad | Fast cut on hard clear coats | Needs care to avoid haze | Hard paint correction |
Detailed reviews
Each pick below is sized for 6-inch backing plates, with the face diameter stated where the listing published it. Colour meanings are given per maker, because they differ across brands.
Top Pick: SPTA HD 5-Piece Buffing Polishing Pads 6-Inch
Top Pick
Why the SPTA HD 5-Piece Buffing Polishing Pads 6-Inch is our pick
This set earns the top spot because it covers the whole sequence in one box: a 6-inch green heavy-cut pad for 1500-grit sanding marks, a yellow medium-cut pad for 2000-grit marks, an orange light-cut pad for 2500-grit marks, a blue polish pad, and a red buff wax pad for finishing. The hook-and-loop backing is described with strong adhesion for repeated use, and the set suits DA and rotary polishers. For a detailer buying one set, that graded completeness beats any single-grade pad.
SPTA HD 5-Piece Buffing Polishing Pads 6-Inch key specs
- Face diameter: 6 inches
- Backing: Hook and loop
- Grades included: 5, heavy to finishing
- Foam thickness: Not published
- Best stage: Full sequence
- Part: FPBGS6MIX
- Count: 5
- Use: Compounding, polishing, waxing
- Polisher type: DA and rotary
- Warranty stated: Not published
SPTA HD 5-Piece Buffing Polishing Pads 6-Inch: fits and best for
Best for detailers who want one graded set for a full correction on a 6-inch plate. It suits cars, trucks and motorcycles with swirls, oxidation and water spots. It is not the pick for a single severe defect, where a dedicated heavy-cut pad plus this set's later grades is the better pairing.
SPTA HD 5-Piece Buffing Polishing Pads 6-Inch pros and watch-outs
- Full graded sequence in one set
- Heavy to finishing coverage
- Hook-and-loop backing
- DA and rotary use
- Clear grade per pad
- Only one pad per grade
- Foam thickness not published
- Needs extra pads for a full car
- Colour meanings differ from other makers
SPTA HD 5-Piece Buffing Polishing Pads 6-Inch: what owners report
- Owner reports paraphrased from the listing page praise the graded set for taking a panel from swirls to gloss without changing brands.
- Other owner notes describe the backing adhesion as reliable across repeated pad changes.
- Full-car pad-count reports note one pad per grade runs out on heavy correction, so the guide says to buy spares for big jobs.
SPTA HD 5-Piece Buffing Polishing Pads 6-Inch: who should not buy
Do not buy this set if you only need one stage, such as waxing a good finish. A single finishing pad costs less and does that job.
SPTA HD 5-Piece Buffing Polishing Pads 6-Inch: pair it with
Pair it with the SPTA microfiber 2-piece set.
We may earn a commission at no cost to you.
Tip: label each pad by grade so colours never confuse stages, and read our finishing polish vs finishing wax guide for final-stage order.
Best Standard Set: SPTA 5-Piece Standard Buffing Polishing Pads 6-Inch
Best Standard Set
Why the SPTA 5-Piece Standard Buffing Polishing Pads 6-Inch is our pick
This set uses SPTA's T-grade system: T120 green heavy-cut, T80 yellow medium-cut, T60 orange medium-cut, and T20 red finishing pads, in 6-inch faces with a 6.9-inch back and 28 mm foam thickness. The listing describes the set for compounding, polishing and waxing on 150 mm polishers, with hook-and-loop backing for easy changes. It is the standard-tier sibling of the HD set above, with published foam thickness that the HD listing does not give.
SPTA 5-Piece Standard Buffing Polishing Pads 6-Inch key specs
- Face diameter: 6 inches
- Backing: Hook and loop
- Grades included: 5, T120 to T20
- Foam thickness: 28 mm
- Best stage: Full sequence
- Part: FPTJS6-MIX
- Back diameter: 6.9 inches
- Count: 5
- Use: Compounding, polishing, waxing
- Warranty stated: Not published
SPTA 5-Piece Standard Buffing Polishing Pads 6-Inch: fits and best for
Best for detailers who want published foam thickness and T-grade clarity in a standard set. It suits the same full-sequence work as the HD set. It is not the pick for buyers who want the HD set's 1500 to 2500-grit mark mapping, which this listing does not publish.
SPTA 5-Piece Standard Buffing Polishing Pads 6-Inch pros and watch-outs
- Published 28 mm foam thickness
- T-grade system is explicit
- Full graded sequence
- Hook-and-loop backing
- 6.9-inch back for plate coverage
- Grit-mark mapping not published
- Only one pad per grade
- Standard tier, not HD
- Colour meanings differ from other makers
SPTA 5-Piece Standard Buffing Polishing Pads 6-Inch: what owners report
- Owner reports paraphrased from the listing page praise the T-grade labels for removing colour guesswork.
- Other owner notes describe the foam thickness as comfortable for curved panels.
- No HD-versus-standard comparison reports were found, so no claim is made there.
SPTA 5-Piece Standard Buffing Polishing Pads 6-Inch: who should not buy
Do not buy this set if you need the HD set's grit-mark mapping for sanding-mark removal. The HD set above publishes that mapping.
SPTA 5-Piece Standard Buffing Polishing Pads 6-Inch: pair it with
Pair it with the SPTA HD 5-piece set.
We may earn a commission at no cost to you.
Tip: keep T-grade labels visible on pad backs, and read our best dual-action polishers under 200 guide for polisher pairing.
Best Plate Safety Margin: SPTA 5-Piece 6.5-Inch Face Mix Pads for 6-Inch Plates
Best Plate Safety Margin
Why the SPTA 5-Piece 6.5-Inch Face Mix Pads for 6-Inch Plates is our pick
This set's geometry is its advantage: a 6.5-inch face on a 6-inch back, with 26 mm foam, hook-and-loop backing, and an X-shaped incision in durable open-cell foam that the listing describes as locking compound in place at speed. The wider face means the backing plate cannot strike paint even on curved panels, which is the most common beginner damage in polishing. The mix covers cutting, polishing and waxing grades in one set.
SPTA 5-Piece 6.5-Inch Face Mix Pads for 6-Inch Plates key specs
- Face diameter: 6.5 inches
- Backing: Hook and loop
- Grades included: Mix, cutting to waxing
- Foam thickness: 26 mm
- Best stage: Full sequence
- Part: SQMIX65
- Back diameter: 6 inches
- Count: 5
- Foam: Open-cell, X incision
- Warranty stated: Not published
SPTA 5-Piece 6.5-Inch Face Mix Pads for 6-Inch Plates: fits and best for
Best for beginners and curved-panel work, where the plate-edge margin matters most. It suits detailers who want the safety of a wider face without changing plates. It is not the pick for tight spots, where a smaller pad fits better than a 6.5-inch face.
SPTA 5-Piece 6.5-Inch Face Mix Pads for 6-Inch Plates pros and watch-outs
- 6.5-inch face protects against plate strikes
- X incision holds compound
- 26 mm open-cell foam
- Mix grades in one set
- Hook-and-loop backing
- Too wide for tight spots
- Grade list less explicit than T-grades
- Only one pad per grade
- Needs a true 6-inch plate
SPTA 5-Piece 6.5-Inch Face Mix Pads for 6-Inch Plates: what owners report
- Owner reports paraphrased from the listing page praise the wider face for curved panels, where narrower pads exposed the plate edge.
- Other owner notes describe the X incision as useful for holding compound at speed.
- Tight-spot reports note the width limit honestly, so the guide states it here.
SPTA 5-Piece 6.5-Inch Face Mix Pads for 6-Inch Plates: who should not buy
Do not buy this set for tight areas such as pillars and bumpers edges. A smaller pad is the honest answer for those spots.
SPTA 5-Piece 6.5-Inch Face Mix Pads for 6-Inch Plates: pair it with
Pair it with the SPTA HD 5-piece set.
We may earn a commission at no cost to you.
Tip: check the face overhang is even all round before switching on, and read our best cordless dual-action polishers under 50 guide for small-area notes.
Best Single Heavy-Cut Pad: Chemical Guys Hex-Logic Quantum Yellow Heavy-Cutting Pad 6.5-Inch
Best Single Heavy-Cut Pad
Why the Chemical Guys Hex-Logic Quantum Yellow Heavy-Cutting Pad 6.5-Inch is our pick
This pad is the single-grade specialist: a 6.5-inch Quantum Hex-Logic foam pad made for 6-inch backing plates, described by the maker as its heaviest hitter for severe and deep defects including swirls, scratches, oxidation and water spots. The Hex-Logic grooves spread product evenly and conform the pad to contoured surfaces, and the Quantum geometry is described as improving cooling and coverage. For severe defects, one correct heavy-cut pad beats a graded set's heavy pad used alone, because the foam is built for that single job.
Chemical Guys Hex-Logic Quantum Yellow Heavy-Cutting Pad 6.5-Inch key specs
- Face diameter: 6.5 inches
- Backing: Hook and loop
- Grades included: 1, heavy cutting
- Foam thickness: Not published
- Best stage: Heavy cutting
- Part: BUFX111HEX6
- Count: 1
- Grooves: Hex-Logic
- Use: DA and rotary
- Warranty stated: Not published
Chemical Guys Hex-Logic Quantum Yellow Heavy-Cutting Pad 6.5-Inch: fits and best for
Best for severe defects on a 6-inch plate, where a graded set's heavy pad is not aggressive enough or has worn out. It suits detailers correcting neglected paint. It is not a full-sequence answer: it must be followed by polishing and finishing pads, or the finish will show haze.
Chemical Guys Hex-Logic Quantum Yellow Heavy-Cutting Pad 6.5-Inch pros and watch-outs
- Built for severe defects
- Hex-Logic grooves spread product
- 6.5-inch face for 6-inch plates
- DA and rotary use
- Contours to curved panels
- Single pad, single grade
- Must be followed by refining pads
- Foam thickness not published
- Yellow means different grades at other makers
Chemical Guys Hex-Logic Quantum Yellow Heavy-Cutting Pad 6.5-Inch: what owners report
- Owner reports paraphrased from review coverage praise this pad for severe swirl and oxidation removal.
- Other owner notes describe the Hex-Logic grooves as useful for even product spread on large flat panels.
- Haze reports confirm the need for refining stages after heavy cutting, so the guide states that plainly.
Chemical Guys Hex-Logic Quantum Yellow Heavy-Cutting Pad 6.5-Inch: who should not buy
Do not buy this pad alone for a full correction. Without refining and finishing pads after it, the finish will not reach gloss.
Chemical Guys Hex-Logic Quantum Yellow Heavy-Cutting Pad 6.5-Inch: pair it with
Pair it with the SPTA HD 5-piece set.
We may earn a commission at no cost to you.
Tip: follow heavy cutting with a polishing pad, never wax straight after, and read our finishing polish vs clear coat guide for stage order.
Best Microfiber: SPTA Microfiber Polishing Pads 6-Inch 2-Piece
Best Microfiber
Why the SPTA Microfiber Polishing Pads 6-Inch 2-Piece is our pick
Microfiber pads cut faster than foam on hard clear coats, and this 2-piece set gives cutting and finishing discs with hook-and-loop backing for 6-inch polishers. The listing describes superfine microfiber that cuts tougher ceramic clear coats and softer one-step paints alike, with good hand feel and toughness. The trade is haze: microfiber cutting usually needs a foam refining stage after it, so this set pairs with, rather than replaces, the foam sets above.
SPTA Microfiber Polishing Pads 6-Inch 2-Piece key specs
- Face diameter: 6 inches
- Backing: Hook and loop
- Grades included: 2, cutting and finishing
- Foam thickness: Not published
- Best stage: Hard-coat cutting
- Part: MPBFS6D-2
- Count: 2
- Material: Superfine microfiber
- Use: Cutting, buffing, waxing, polishing
- Warranty stated: Not published
SPTA Microfiber Polishing Pads 6-Inch 2-Piece: fits and best for
Best for hard clear coats and ceramic coatings where foam cutting stalls. It suits experienced detailers who follow microfiber cutting with foam refining. It is not the beginner pick, because microfiber haze needs a refining stage to correct.
SPTA Microfiber Polishing Pads 6-Inch 2-Piece pros and watch-outs
- Fast cut on hard clear coats
- Cutting and finishing discs
- Hook-and-loop backing
- Tough superfine microfiber
- Suits ceramic coatings
- Can leave haze without refining
- Only 2 discs
- Needs a foam set after it
- Not a beginner first set
SPTA Microfiber Polishing Pads 6-Inch 2-Piece: what owners report
- Owner reports paraphrased from the listing page praise microfiber cutting speed on hard paint.
- Other owner notes confirm the need for a foam refining stage after microfiber cutting.
- Beginner reports note haze where refining was skipped, so the guide warns against skipping it.
SPTA Microfiber Polishing Pads 6-Inch 2-Piece: who should not buy
Do not buy this set as your only pads. Without foam refining pads after it, the finish will show haze on most paint.
SPTA Microfiber Polishing Pads 6-Inch 2-Piece: pair it with
Pair it with the SPTA HD 5-piece set.
We may earn a commission at no cost to you.
Tip: always follow microfiber cutting with foam polishing, and read our top cordless dual-action polishers on the market guide for polisher notes.
Spec comparison
Figures below come from the maker or retailer listing for each product. Where a listing did not publish a figure, the cell reads Not published.
| Spec | SPTA HD set | SPTA standard set | SPTA 6.5-inch face |
|---|---|---|---|
| Face diameter | 6 inches | 6 inches | 6.5 inches |
| Backing | Hook and loop | Hook and loop | Hook and loop |
| Grades included | 5, heavy to finishing | 5, T120 to T20 | Mix, cutting to waxing |
| Foam thickness | Not published | 28 mm | 26 mm |
| Best stage | Full sequence | Full sequence | Full sequence |
| Part | FPBGS6MIX | FPTJS6-MIX | SQMIX65 |
| Count | 5 | 5 | 5 |
| Back diameter | Not published | 6.9 inches | 6 inches |
| Polisher type | DA and rotary | Not published | Not published |
| Foam | Not published | Not published | Open-cell, X incision |
| Check Price | Check Price | Check Price | Check Price |
| Spec | Chemical Guys yellow | SPTA microfiber |
|---|---|---|
| Face diameter | 6.5 inches | 6 inches |
| Backing | Hook and loop | Hook and loop |
| Grades included | 1, heavy cutting | 2, cutting and finishing |
| Foam thickness | Not published | Not published |
| Best stage | Heavy cutting | Hard-coat cutting |
| Part | BUFX111HEX6 | MPBFS6D-2 |
| Count | 1 | 2 |
| Back diameter | Not published | Not published |
| Use | DA and rotary | Cutting, buffing, waxing, polishing |
| Foam | Not published | Superfine microfiber |
| Check Price | Check Price | Check Price |
Editorial judgement, not test results: the comparison above weighs published specifications, fitment breadth, and owner-report themes. It is not a laboratory ranking.
Fitment and use basics
Centre the pad on the backing plate, press it firmly onto the hook-and-loop surface, and spin it by hand to check it sits true before switching on. Work a small section at a time, keep the pad flat, and clean it before it loads up. Read our best dual-action polishers under 200 guide for polisher pairing, and finishing polish vs clear coat for stage order.
Start with the least aggressive pad and compound that removes the defect, and step up only if the defect remains. A heavy-cut pad on soft paint removes clear coat you cannot put back, so test on an inconspicuous panel first. See also best cordless dual-action polishers under 50 for cordless pairing notes.
Safety essentials
1. Wear eye protection; compound spray and pad debris leave the pad at speed.
2. Keep cords clear of the pad and the panel edge.
3. Never run a pad with a torn backing or collapsed foam.
4. Keep the pad flat; a tilted pad burns edges and throws compound.
5. Let the polisher stop fully before setting it down.
6. Wash hands after handling compounds; keep compounds off skin and eyes.
Three accessories that help with safe polishing work are listed below. A graded foam set covers the full sequence, a single heavy-cut pad handles severe defects, and a microfiber set handles hard clear coats. Each carries its own verified button.
SPTA HD 5-piece set, for the full graded sequence.
Chemical Guys yellow heavy-cutting pad, for severe defects.
SPTA microfiber polishing pads 6-inch 2-piece, for hard clear coats.
Troubleshooting
| Symptom | Likely cause | Fix |
|---|---|---|
| Pad flies off at speed | Worn backing or dirty pad back | Replace plate or pad, clean backing |
| Holograms after polishing | Pad too aggressive or dirty | Step down a grade, clean pads |
| Pad overheats and collapses | Too much pressure or speed | Reduce pressure, rotate pads |
| Plate edge strikes paint | Pad face too small | Use a wider face than the plate |
| Uneven cutting | Loaded pad or tilted polisher | Clean pad, keep polisher flat |
| Compound will not wipe off | Too much product or wrong pad | Use less product, match pad grade |
Who should NOT buy these
Do not buy a single pad for a full correction. Correction is a sequence, and one pad cannot cut, refine and finish. Buy a graded set, or accept that the finish will show it.
Do not carry colour meanings across brands. Yellow is heavy cut at one maker and medium cut at another. Read the grade for the pad you bought, not the colour you remember.
Do not use a pad with a torn backing. A torn backing lets the pad fly off or the plate strike paint. Retire damaged pads instead of nursing them through a job.
Final verdict
Top Pick — SPTA HD 5-Piece Buffing Polishing Pads 6-Inch: Check Price
Best Standard Set — SPTA 5-Piece Standard Buffing Polishing Pads 6-Inch: Check Price
Best Plate Safety Margin — SPTA 5-Piece 6.5-Inch Face Mix Pads for 6-Inch Plates: Check Price
Best Single Heavy-Cut Pad — Chemical Guys Hex-Logic Quantum Yellow Heavy-Cutting Pad 6.5-Inch: Check Price
Best Microfiber — SPTA Microfiber Polishing Pads 6-Inch 2-Piece: Check Price
FAQ
What size pad fits a 6-inch backing plate?
A pad with a face wider than 6 inches, typically 6.5 inches, so the plate edge cannot touch paint. The SPTA 6.5-inch face set below is built exactly for that margin, while 6-inch-face pads need a careful plate check.
How many pads do I need for a full car?
More than one per stage. A full correction loads pads with compound and paint residue, so rotating through several pads per grade keeps cutting even and prevents overheating. A 5-piece graded set is a starting point, not a one-car supply for heavy correction.
What do pad colours mean?
They mean whatever the maker says for that pad line. Chemical Guys yellow is heavy cutting, while SPTA yellow is medium cutting, so colour alone never identifies a grade. Read the grade printed for your own pads.
Foam or microfiber pads?
Start with foam: it cuts smoothly and finishes cleanly for most paint. Add microfiber where foam cutting is too slow on hard clear coats, and follow it with a foam refining stage to remove any haze.
Can I wash polishing pads?
Yes, with pad cleaner or warm water and mild detergent, rinsed thoroughly and air-dried face up. A pad that stays loaded with compound cuts unevenly, and a pad dried with heat can warp its backing.
When should I replace a pad?
When foam has collapsed, torn or hardened, when the backing no longer grips, or when cleaning no longer restores even cutting. A worn pad costs more in paint damage than a new pad costs to buy.
Can I use 6-inch pads on a 5-inch plate?
Yes, where the pad's hook-and-loop back fits the plate and the face overhang is even, but check the listing: some 6-inch-face pads are described for 5-inch plates and some are not. An uneven overhang vibrates and cuts unevenly.
What is the difference between cutting and polishing pads?
Cutting pads use coarser, firmer foam to remove defects and a thin layer of clear coat, while polishing pads use softer foam to refine the finish after cutting. Finishing pads have no cut and spread wax or glaze.
Do I need a different pad for each compound?
Yes in practice: keep one pad per compound grade, and label pads so a heavy-cut pad never carries a finishing polish. Cross-contamination puts coarse abrasive into a finishing stage and undoes the refinement.
Sources
Manufacturer and retailer sources: SPTA HD 5-piece set listing; SPTA 5-piece standard set listing; SPTA 6.5-inch face mix set listing; Chemical Guys yellow pad listing; SPTA microfiber 2-piece set listing.
Pad colour meanings are quoted per maker from the listing for each product. Where a listing did not publish a figure, the guide prints Not published.
By Leo, Founder, WinchInsider
Leo founded WinchInsider to give drivers clear, research-based buying guides without invented specifications or testing claims. Every guide is checked against maker documents and retailer specifications before it is published.
Related guides
More in Car Cleaning and Detailing
Best dual-action polishers under 200
Finishing polish vs clear coat
Best cordless dual-action polishers under 50
Best cordless rotary polishers under 1000
Top cordless dual-action polishers on the market
Best waterproof headlight polishing compound
Top cordless rotary polishers under 200
Best LED headlight polish vs polish
Waterproof headlight polish alternative DIY
Best LED headlight polish dry time
Top pick: SPTA HD 5-Piece Buffing Polishing Pads 6-Inch Check Price